Would like to tweak my system with a z matcher. Would be used on the 2 meter
band. Anyone have a nice 'cheap' one they would part with? :-)
Thanks,
Ben-W4WSM
?
Ben-W4WSM
@yahoogroups.com
Subject: Re: [Repeater-Builder] Lost 10 volts in a Master II UHF
Repeater
Could be a dirty contact on the backplane.
Chuck
WB2EDV
- Original Message -
From: w4wsm b.run...@... mailto:b.runner%40insightbb.com
To: Repeater-Builder@yahoogroups.com
I noticed my Micor repeater's power supply has a black/wire hanging
off a couple terminals in the back. May have been a battery back up
connnected...does the PS have a charging circuit? Just wondering if I
could hook up a battery to it direct...
Ben
repeaters than most states. Not that we need more but we do
need to have an active coordination council in this area.
Ben-W4WSM
My point to all of this is that we need to remember that these
coordinator's jobs are voluntary, and are done as a hobby, in spare
time
that is pulled away from
I'm in the process of getting a voting system up and running. Never
played with one before but I'm learning a lot...
Now I'm at the point of setting up the voter with a link receiver and
an exciter here at the house. The voter is seeing the COS when the RX
is active and audio is getting to the
very hard to find someone with a RLC5 and Link says it
shouldn't be a problem with the firmware...
Ben
W4WSM
Anyone know where I can find unsquelched audio in a Phoenix? Even
squelched but not through the volume control may work too...
Thanks,
Ben
Don't care about TX just need to RX down in the 147 band. The 2
channel will do fine but I can use any of them.
If anyone has one or more of these gathering dust they would part with
'cheap!' let me know!
Thanks,
Ben
I have an old COR2 that I have no docs for. Hamtronics doesn't have
info either...anyone have one of these they may have the manual for?
Thanks,
Ben
I'm looking at a TPE voter one of the list members has. Anyone on here
ever heard of it or know anything about it?
Thanks!
Ben
W4WSM
for this one...
Thanks!
Ben
W4WSM
Hi,
Any idea what kind of bandwidth a full size station master would have?
VHF marked 153.XX...should it go down into the 2 meter band or are
they very narrow?
Ben
Is it something that can be done in the field? I'm thinking a big
multielement fiberglass antenna...haven't seen it yet.
Ben
--- In Repeater-Builder@yahoogroups.com, Ken Arck [EMAIL PROTECTED] wrote:
At 01:36 PM 2/17/2007, you wrote:
Hi,
Any idea what kind of bandwidth a full size
I put a single notch can on my rx today rejecting my TX and passing
RX. Seems to have taken care of the problem with 93 getting in. I'll
get to test it more later but so far it's fine even with a close in
high power station...
Thanks for all the comments and help to everyone who replied.
Ben
--- In Repeater-Builder@yahoogroups.com, Nate Duehr [EMAIL PROTECTED] wrote:
On 2/7/07, w4wsm [EMAIL PROTECTED] wrote:
Yes, CG is on transmitter. I pulled the cable to it and the TX went
off. It wouldn't key with the tone disconnected...is there a jumper
you have to use for no tone?
I'm
Repeater. Does it with only the 10 volt card when no controller is
hooked up.
This started it's life as a repeater. It's not a remote base.
--- In Repeater-Builder@yahoogroups.com, Fred Flowers
[EMAIL PROTECTED] wrote:
Yes there is a jumper. Is this a repeater? Most likely the trouble
is
and turns on the LED. THe schematic
for this board is on the Repeater-builders website where the LBIs
are posted. Good luck!
AC0Y
--- In Repeater-Builder@yahoogroups.com, w4wsm b.runner@
wrote:
Repeater. Does it with only the 10 volt card when no controller is
hooked up
I have two stations and swapped all the cards from the working
one...it stays keyed.
It's like a puzzle...
Ben
A shorted transistor in the keying circuit on the 10V Reg card maybe?
Jamey Wright
Systems Analyst
Morgan Coun
Just went down and checked a few things.
Yes, CG is on transmitter. I pulled the cable to it and the TX went
off. It wouldn't key with the tone disconnected...is there a jumper
you have to use for no tone?
It's the intercom button on the 10volt card that causes the tx to go
off when you push it.
--- In Repeater-Builder@yahoogroups.com, Jeff DePolo [EMAIL PROTECTED]
wrote:
Are you doing these tests while using an outboard controller?
PA is into a dummy load so I don't think it's RF.
Haven't disconnected the PA but will try as soon as it gets a little
warmer. It is putting out full
Well just found this group so here is another question...last for now
I promise:-)
My 2600 service monitor has lost a lot of it's hearing. Is still 100%
on everything else but it has lost a lot sens. It was just one of
those turn it on and what happened type of thing.
Any ideas on this one?
OK, I didn't see this before. Makes sense but I wonder why it didn't
start until you put the new station up? Fred, anytime you want to come
up it's fine with me...you are always welcome here...the building is a
little nicer now than when you built the tower!
Ben
repeater is not interfered
I have a mastr II station that has me wondering...
No matter what I do it will not unkey. Tried swapping out all the
cards and it didn't make a difference. I can get it to unkey by
pushing I think it's the ptt remote switch.
Any ideas?
Thanks,
Ben
My display is pretty good but I've heard of the problems. I have a
good RGB color monitor waiting for when it goes out.
Ben
Yes, red TX light is on and it has good output.
--- In Repeater-Builder@yahoogroups.com, Fred Flowers
[EMAIL PROTECTED] wrote:
Is the TX light on the 10 v reg on is the radio putting out power?
Fred N4GER
It hung up without warning. Was up on the hill doing fine then I
noticed the carrier on...No pl.
Thanks,
Ben
--- In Repeater-Builder@yahoogroups.com, Jeff DePolo [EMAIL PROTECTED]
wrote:
I have a mastr II station that has me wondering...
No matter what I do it will not unkey. Tried
:[EMAIL PROTECTED] On Behalf Of w4wsm
Sent: Tuesday, February 06, 2007 8:02 AM
To: Repeater-Builder@yahoogroups.com
Subject: [Repeater-Builder] Low sens on a 2600 monitor
Well just found this group so here is another question...last for now
I promise:-)
My 2600 service monitor has lost
28 matches
Mail list logo