OK Mike - you were firstest with the responsists so you get it.
Which hamfest you talking about? The one in Ocala is next Sat. I'll be going to
that one
since I live between Inverness and Ocala. We can meet there. In the event
you're interested in other VHF stuff from the estate, perhaps you'd
I have a VHF Syntor and a few UHF MCX100s. I'm looking into purchasing
PROMs to program them with. The UHF MCXs had the knob-stop removed and
it now turns to all 16 positions, however the Syntor is bare and may be
strapped for a single frequency.
Jameco lists the N82S129 (256x4) for $11, and
A quick check of the datasheets shows that the only difference is pin 14
which is a second chip-enable line on the smaller device, whereas it's the
most significant address bit on the larger device. The Syntor can address
either the smaller or bigger part depending on jumpers. If your radio was
Hello Eric, K6TC here and like so many these days I am looking for a qualified
technician that might be able to set my repeater right for immediate install?
Built By Jim Ward formerly of the Condor connections group of Hams that saw to
the maintence an up-keep of that system. I moved from the
i have problems with programming relm chatral radios smvi 40 e smv 40, help me
please
Rodrigo
Here in my local area, there is a battery dealer that handles used take outs
in the AGM models. These are from telephone or commercial back up systems where
the batteries are replace every year, if they need it or not. We have been able
to buy 100 - 150 AH models from $45-$75 each. I run my
Hi Guys,
Why not use AGM batteries and reduce the
explosion problems. They can be mounted in any
position and do not have need for water filling
or venting applications, however I would
recommend they not be sealed in a box and have
some slight venting. There is some good battery
Please take a look at the image in the file section hamtronicsR10576.jpg. I
think this is an old hamtronics RX/TX strip. The RX is on the left and the TX
on the right.
Thanks for any help
-Dan WA6PZB
Hello All.
I am looking for information on a Uniden SRH150DT repeater.It powers up and
rx/tx just fine.The current freq. are in the 160 mhz range.Does any one know
what software version is used to program this unit?.Any one have a PDF copy of
a Instruction manual or even the original manual
I would like to purchase the thermistor.
Ron, AA5NI..
- Original Message -
From: sjotrollet
To: Repeater-Builder@yahoogroups.com
Sent: Friday, December 04, 2009 10:51 AM
Subject: [Repeater-Builder] FS: Thermosistor Mount
HP model 478A, 200-ohm. From an estate and
Hello Everyone, I have just joined up to the group to see if someone here might
need parts for a GE Master II (I think). Here are a couple of part #'s that I
have new in the box!!
19c321017g1 tone incoder
4ef39a11 PA board
And a few other parts that are new.
If someone needs these
Hello,
Can someone take a look at the pix in the files section (hamtronicsR10576.jpg).
This is a PIX of RX and TX strip for 220 Mhz. I believe they are old hamtronics
units. I would like to find scans of the manual if someone has them. The RX is
on the left of the image and seems to be in 4
try to look at www.cqham.ru
--- On Sun, 11/15/09, UnixRoo yo3...@ynos.ro wrote:
From: UnixRoo yo3...@ynos.ro
Subject: [Repeater-Builder] KPG-60D
To: Repeater-Builder@yahoogroups.com
Date: Sunday, 15 November, 2009, 7:06 PM
Hello friends,
I have a
I am on the lookout for a couple Micor stations and Mitrek mobiles on the
406-420 UHF split.
If anybody has some they are willing to part with, please contact me off list.
Thanks,
Joe - WA7JAW
Re: Manual for Hamtronics (actually VHF
Engineering) kit RX TX
The picture depicts a VHF Engineering Transmitter
and Receiver Setup.
VHF Engineering Transmitters properly aligned are
still quite usable. As you have probably noticed it
and the receiver are both crystal controlled.
Their
The Kenwood TK-880 radio programs with the KPG-49d software,
which is all over the web...
s.
UnixRoo yo3...@... wrote:
Hello friends,
I have a Kenwood TK-880-1 and i want to write another freq. but i dont find
the programing software KPG-60D, can some one help me with the program?
to the outside. I have experienced no
complications following this procedure, either with corrosion or explosive
events.
Good Luck,
Rich
N9EMS
__ Information from ESET NOD32 Antivirus, version of virus signature
database 4663 (20091205) __
The message was checked by ESET
Best off + shipping. Please respond direct.
73,
dave
wa3gin
18 matches
Mail list logo
