Bernard,
I've divided this message up further to ensure I don't cause any problems with message size limits. The first page is my screen outputs (along with original letter) and the second is my bios settings.
Thanks for your suggestions. I've included below the output of the screen during the boot. It picks up after it has started its network boot (it's already gotten the offer from eth1 through DHCP.) Note, the chassis doesn't have the SOL link set up properly on the MM (as the CISCO switches cause some problems with that) so I had to screen capture and then copy all the below information by hand. I tried to be meticulous, but it's possible I fat fingered something. Does any of the output information give a hint as to why the eth1 is not? Is it possible there's a problem with the autonegotiation of interrupts of the eth cards? Would setting them to definite values in the BIOS help? Even a suggestion on why the screen is freezing after the dhcp fails would be appreciated.
Again, thank you guys for your suggestions, the help is greatly appreciated.
I've divided this message up further to ensure I don't cause any problems with message size limits. The first page is my screen outputs (along with original letter) and the second is my bios settings.
Thanks for your suggestions. I've included below the output of the screen during the boot. It picks up after it has started its network boot (it's already gotten the offer from eth1 through DHCP.) Note, the chassis doesn't have the SOL link set up properly on the MM (as the CISCO switches cause some problems with that) so I had to screen capture and then copy all the below information by hand. I tried to be meticulous, but it's possible I fat fingered something. Does any of the output information give a hint as to why the eth1 is not? Is it possible there's a problem with the autonegotiation of interrupts of the eth cards? Would setting them to definite values in the BIOS help? Even a suggestion on why the screen is freezing after the dhcp fails would be appreciated.
Again, thank you guys for your suggestions, the help is greatly appreciated.
Output of screen during booting: after it gets its initial pxelinux.cfg file:
Welcome to SystemImager:
*Systemimager message*
boot:
load kernel
.
load initrd.img
Ready
.
896MB LOWMEM available
Checking if this processor honours the WP bit even in supervisor mode. . . Ok.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8k
CPU: L2 cache: 512k
CPU: Intel® Xeon CPU 3.06GHZ stepping 09
Enabling fast FPU save and restore. . . done
Enabling unmasked SIMD FPU exception support. . .done.
Checking hlt instruction. . .ok
ACPI: setting ELCR to 0010 (from 0eb8)
Checking if image is initramfs
it isnt (no cpio magic); looks like an initrd
Freeing initrd memory:700k freed
NET: Registrered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd82c, last bus=4
PCI: Using configuration type 1
ACPI: Subsytem revision 20041105
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDR controller 0000:00:0f.1
ACPI: PCI Root Bridge [PCI1] (00:02)
PCI: Probing PCI h
ardware
(bus 02)
ACPI: PCI Root Bridge [PCI2] (00:01)
PCI: Probing PCI hardware (bus 01)
ACPI: PCI Interrupt Link [LPUS] (IRQs *7)
ACPI: PCI Interrupt Link [LPID] (IRQs *14)
Usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
**PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
**workaround, the pci=routeirq argument restores the old
**behavior. If this argument makes the device work again,
** please email the output of lspci to [EMAIL PROTECTED]
**so I can fix the driver.
devfs: 2004-01-31 Richard Gooch ([EMAIL PROTECTED])
devfs: boot_options: 0x1
Initializing Cryptographic API
ACPI: Power Button (FF) [PWRF]
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled<
/div>
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
elevator: using anticipatory as default io scheduler
Floppy drive(s): fd0 is 1.44M
RAMDISK driver initialized: 16 RAM disks of 8192k size 4096 blocksize
loop: loaded (max 8 devices)
Intel® PRO/1000 Network Driver version 5.5.4-k2-NAPI
Copyright © 1999-2004 Intel Corporation
Intel® PRO/10Gbe Network Driver version 1.0.66-k2
Copyright © 2001-2004 Intel Corporation
dgrs:
SW=$Id:
dgrs.c,v 1.13 2000/06/06 04:07:00 rick Exp $ FW=Build 550 11/16/96
03:45:15
FW Version=$Version$
pcnet32.c:v1.30i 06.28.2005 [EMAIL PROTECTED]
e100: Intel® PRO/100 Network Driver, 3.2.3-k2-NAPI
e100: Copyright© 199-2004 Intel Corporation
nsB3B20.c: National Semiconductor DPB3B20 10/100/1000 driver.
tg3.c:v2.14 (November 15, 2004)
ACPI: PCI interrupt 0000:01:00.0[A]: no GSI using IRQ 10
eth0: Tigon3 [partno BCM95704A41) rev 2002 PHY(serdes)] (PCIX:133MHz:64-bit) 10/
100/1000BaseT Ethernet 00:0d:60:9d:76:36
eth0: RXcsums[1] LinkChgReg[0] MIirq[0] ASF[1] Split[0] WireSpeed[1] TSOcap[0]
ACPI: PCI interrupt 0000:01:00.1[B]: no GSI using IRQ 11
Eth1: Tigon3 [partno BCM95704A41) rev 2002 PHY(serdes)] (PCIX:133MHz:64-bit) 10/
100/1000BaseT Ethernet 00:0d:60:9d:76:37
eth1: RXcsums[1] LinkChgReg[0] MIirq[0] ASF[1] Split[0] WireSpeed[1] TSOcap[1]
dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
winbond-B40.c:v1.01-d (2.4 port) Nov-17-2001 Donald Becker [EMAIL PROTECTED]
<
div
class="MsoNormal"> http://www.scyld.com/network/drivers.htmlUniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SvrWks CSB6: IDE controller at PCI slot 0000:00:0f.1
SvrWks CSB6: chipset revision 176
SvrWks CSB6: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x0700-0x0707, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0x070B-0x070F, BIOS set
tings:
hdc:DMA, hdd:DMA
hda: FUJITSU MHT2040AS, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: FUJITSU MHT2040AS, ARA DISK drive
ide1 at 0x170-0x177, 0x376 on irq 15
hda: 78140160 sectors (4006 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2
hdc: max request size: 128KiB
hdc: 78140160 sectors (40007 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
/dev/ide/host0/bus1/target0/lun0: p1
ide-floppy driver 0.99.newide
ACPI: PCI interrupt 0000:00:0f.2[A]: no GSI using IRQ
7
ohci_hcd 0000:00:0f.2: ServerWorks CSB6 OHCI USB Controller
ohci_hcd 0000:00:0f.2: irq 7, pci mem 0xfebfe000
ohci_hcd 0000:00:0f.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
USB Universal Host Controller Interface driver v2.2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device commn for all mice
I2d Core © Copyright 1999 Red Hat Software.
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered
protocol
family 2
IP: routing cache has table of 8192 buckets, 64k bytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun
md:
autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 816K freed
init started: BusyBox v1.00 (2005.07.23-21:30+0000) multi-call binary
[: missing ]
grep: ] : No such file or directory
Loading tmpfs
[: missing ]
grep: ]: No such file or diretory
Didnt load assuming its built into the kernel.
[: missing ]
grep: ]: No such file or directory
[: missing ]
grep: ]: No such file or directory
mount_proc
[: missing ]
grep: ]: No such file or directory
u
sb 1-2:
new full speed USB device using ohci_hcd and address 2
Internet Software Consortium DHCP Client 2.0p15
Copyright 1995, 1996, 1997, 1998, 1999 The Internet Software Consurtium
All rights reserved
Please contribute if you find this software useful
For info, please visit http://www.isc.org/dhcp-contrib.html
ohci_hcd 0000:00:0f.2: Unlink after no-IRQ? Different ACPI or APIC settings may help
tg3: eth1: Link is up at 1000MBps, full duplex
tg3: eth1: flow control is off for TX and off for RX
tg3: eth0: Link is up at 1000 Mbps, full duplex
tg3: eth0: Flwo control is off for TX and off for RX.
Listening on LPF/lo/<null>
Sending on LPF/lo/<null>
Listening on LPF/eth1/00:0d:60:9d:76:37
Sending on LPF/eth1/00:0d:60:9d:76:37
Listening on LPF/eth0/00:0d:60:9d:76:36
Sending on LPF/eth0/00:0d:60:9d:76:36
Sending on Socket/fallback/fallback-net
Sending on Socket/fallback/fallback-net
DHCPDISCOVER on lo to 255.255.255.255 port 67 interval 7
DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 3
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 5
DHCPDISCOVER on lo to 255.255.255.255 port 67 interval 7
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 10
DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 7
DHCPDISCOVER on lo to 255.255.255.255 port 67 interval 7
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9
DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 11
DHCPDISCOVER on lo to 255.255.255.255 port 67 interval 16
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7
DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 12
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 10
DHCPDISCOVER on lo to 255.255.255.255 port 67 interval 16
DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 9
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9
No DHCPOFFERS received
No working leases in persistent database sleeping
[: missing ]
grep: ] : No such file or directory
I couldnt configure the network interface using DHCP
[: missing ]
grep: ]: No such file or diretory
[: missing ]
grep: ]: No such file or directory
Killing off running processes.
[: missing ]
grep: ]: No such file or directory
[: missing ]
grep: ]: No such file or directory
write_variables
[: missing ]
grep: ]: No such file or directory
Then th
e
standard This is the Systemimager autoinstall system, your autoinstall has failed, message
BusyBox v1.00 (2005.07.23-21:30+0000) Built-in shell (ash)
Enter help for a list of built-in commands.
/my_modules #
Yahoo! Photos
Ring in the New Year with Photo Calendars. Add photos, events, holidays, whatever.
