Hi,
Im quite new with openbsd. slowly getting to grips with it.
I've two problems. The first is a regular connection problem i've seen people
on the list discuss.
I've a Pentium 120 with 32meg that i want to turn into a router, with no keyboard,
mouse or
monitor. I've installed openbsd 3.1 on and have followed the instructions for
installing
the alcatel management .o library and the speedtouch software (1.1), which went
well.
Ill state my second problem first ;) Most people wont read till the end of my
post I gather :)
My second problem occurs when I start my box witht modem connected. It goes
into a panic
when the ohci section starts, printing the error: "ohci_intr: ignored interrupt
while polling"
over and over, seemingly stuck in an endless loop. If i do not connect the modem
and wait until
the usb hub is registered all is well, the modem is recognised. Has anyone seen
this bug? It
makes my plans for a openbsd router seem quite dead.
The other problem is that I cannot connect using the instructions given with
the software.
I can't connect when using ppp -background, and I try ppp -ddial, ifconfig -a
reports that tun0
is up but about a minute after this system locks up!
>From what I can see in my logs the modem is recognised and is ready, as shown
below.
OpenBSD 3.1 (GENERIC) #59: Sat Apr 13 15:28:52 MDT 2002
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
<snip>
pchb0 at pci0 dev 0 function 0 "Intel 82437FX" rev 0x01
pcib0 at pci0 dev 7 function 0 "Intel 82371FB PCI-ISA" rev 0x02
ohci0 at pci0 dev 13 function 0 "CMD Technology USB0673" rev 0x05: irq 9, OHCI
v
ersion 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: vendor 0x0000 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
<snip>
ugen0 at uhub0 port 1
ugen0: ALCATEL Speed Touch USB, rev 1.10/0.00, addr 2
After I put /usr/local/sbin into path and run modem_run I get the following
results
Aug 13 21:41:48 bsdserver modem_run[27299]: modem_run version 1.1 started by
root uid 0
Aug 13 21:42:13 bsdserver modem_run[29230]: modem_run version 1.1 started by
root uid 0
Aug 13 21:42:13 bsdserver modem_run[29230]: Found ALCATEL SpeedTouch USB modem
Aug 13 21:42:13 bsdserver modem_run[29230]: Best offset 6463 with probability
100
Aug 13 21:42:14 bsdserver modem_run[29230]: Best offset 526179 with probability
100
Aug 13 21:42:16 bsdserver modem_run[29230]: BLOCK1 : 991 bytes uploaded
: OK
Aug 13 21:42:16 bsdserver modem_run[29230]: BLOCK2 : 511 bytes downloaded
: OK
Aug 13 21:42:18 bsdserver modem_run[29230]: BLOCK3 : 526187 bytes uploaded
: OK
Aug 13 21:42:18 bsdserver modem_run[29230]: Downloaded in 2295.891000 ms
Aug 13 21:42:18 bsdserver modem_run[29230]: BLOCK4 : 511 bytes downloaded
: OK
Aug 13 21:42:19 bsdserver modem_run[29230]: Modem reference : 3EC18607GAAB02
Aug 13 21:42:38 bsdserver modem_run[17318]: Received interrupt, len = 6
Aug 13 21:42:38 bsdserver modem_run[29230]: ADSL synchronization has been obtained
Aug 13 21:42:38 bsdserver modem_run[29230]: Modem State
Aug 13 21:42:38 bsdserver modem_run[29230]: ADSL line is up (576 kbit/s down
| 288 kbit/s up)
Aug 13 21:42:47 bsdserver ppp[6527]: tun0: Warning: Add route failed: 0.0.0.0/0:
errno: No such process
(END)
Then I run ppp, but this fails:
Aug 13 21:42:47 bsdserver ppp[6527]: Phase: Using interface: tun0
Aug 13 21:42:47 bsdserver ppp[6527]: Phase: deflink: Created in closed state
Aug 13 21:42:47 bsdserver ppp[6527]: tun0: Command: adsl: set authname <snipped>
Aug 13 21:42:47 bsdserver ppp[6527]: tun0: Command: adsl: set authkey ********
Aug 13 21:42:47 bsdserver ppp[6527]: tun0: Command: adsl: set device !pppoa2
-vpi 0 -vci 38 -v 2
Aug 13 21:42:47 bsdserver ppp[6527]: tun0: Command: adsl: accept chap
Aug 13 21:42:47 bsdserver ppp[6527]: tun0: Command: adsl: set speed sync
Aug 13 21:42:47 bsdserver ppp[6527]: tun0: Command: adsl: set timeout 0
Aug 13 21:42:47 bsdserver ppp[6527]: tun0: Command: adsl: enable lqr
Aug 13 21:42:47 bsdserver ppp[6527]: tun0: Command: adsl: set lqrperiod 5
Aug 13 21:42:47 bsdserver ppp[6527]: tun0: Command: adsl: set redial 15 10000
Aug 13 21:42:47 bsdserver ppp[6527]: tun0: Command: adsl: set dial
Aug 13 21:42:47 bsdserver ppp[6527]: tun0: Command: adsl: set ifaddr 10.0.0.1/0
10.0.0.2/0 255.255.255.0 0.
0.0.0
Aug 13 21:42:47 bsdserver ppp[6527]: tun0: Command: adsl: add default HISADDR
Aug 13 21:42:47 bsdserver ppp[6527]: tun0: Warning: Add route failed: 0.0.0.0/0:
errno: No such process
Aug 13 21:42:47 bsdserver ppp[6527]: tun0: Command: adsl: enable dns
Aug 13 21:42:47 bsdserver ppp[3523]: tun0: Phase: PPP Started (background mode).
Aug 13 21:42:47 bsdserver ppp[3523]: tun0: Phase: bundle: Establish
Aug 13 21:42:47 bsdserver ppp[3523]: tun0: Phase: deflink: closed -> opening
Aug 13 21:42:47 bsdserver ppp[3523]: tun0: Phase: deflink: Connected!
Aug 13 21:42:47 bsdserver ppp[3523]: tun0: Phase: deflink: opening -> dial
Aug 13 21:42:47 bsdserver ppp[3523]: tun0: Chat: deflink: Dial attempt 1 of
10000
Aug 13 21:42:47 bsdserver ppp[3523]: tun0: Phase: deflink: dial -> carrier
Aug 13 21:42:47 bsdserver ppp[3523]: tun0: Phase: deflink: carrier -> login
Aug 13 21:42:47 bsdserver ppp[3523]: tun0: Phase: deflink: login -> lcp
Aug 13 21:42:47 bsdserver pppoa2[19802]: Starting PPPoA2 ( merged version includes
new ATM/AAL5 stack ) 1.1
Aug 13 21:42:47 bsdserver pppoa2[19802]: Using vpi=0, vci=38
Aug 13 21:42:47 bsdserver pppoa2[19802]: I'm the parent process, I handle
the endpoint 0x07
Aug 13 21:42:47 bsdserver pppoa2[19802]: pty descriptors : fdin=3, fdout=4
Aug 13 21:42:47 bsdserver pppoa2[19802]: Increasing SNDBUF from 2048 to 65536
Aug 13 21:42:47 bsdserver pppoa2[19802]: Increasing RCVBUF from 4096 to 65536
Aug 13 21:42:47 bsdserver pppoa2[19802]: Got the modem !
Aug 13 21:42:47 bsdserver pppoa2[5811]: I'm the children process, I handle the
endpoint 0x87
Aug 13 21:43:03 bsdserver ppp[3523]: tun0: Phase: deflink: Disconnected!
Aug 13 21:43:03 bsdserver ppp[3523]: tun0: Phase: deflink: lcp -> logout
Aug 13 21:43:03 bsdserver ppp[3523]: tun0: Phase: deflink: logout -> hangup
Aug 13 21:43:03 bsdserver ppp[3523]: tun0: Phase: deflink: Disconnected!
Aug 13 21:43:03 bsdserver ppp[3523]: tun0: Phase: deflink: Connect time: 16
secs: 0 octets in, 130 octets o
ut
Aug 13 21:43:03 bsdserver ppp[3523]: tun0: Phase: deflink: : 0 packets in, 5
packets out
Aug 13 21:43:03 bsdserver ppp[3523]: tun0: Phase: total 8 bytes/sec, peak 10
bytes/sec on Tue Aug 13 21:42
:51 2002
Aug 13 21:43:03 bsdserver ppp[3523]: tun0: Phase: deflink: HUPing 19802
Aug 13 21:43:03 bsdserver ppp[3523]: tun0: Phase: deflink: hangup -> closed
Aug 13 21:43:03 bsdserver ppp[3523]: tun0: Phase: bundle: Dead
Aug 13 21:43:03 bsdserver ppp[3523]: tun0: Phase: PPP Terminated (normal).
Aug 13 21:43:03 bsdserver pppoa2[19802]: Killed by a signal 1
Aug 13 21:43:03 bsdserver ppp[3523]: tun0: Chat: Parent notified of failure
Aug 13 21:43:03 bsdserver ppp[6527]: tun0: Phase: Parent: Child failed (errdead)
I've had a look through the archives and noticed similar problems. I tried using
-ddial and this seems to work.
The last message I get is the line from above:
Aug 13 21:42:47 bsdserver pppoa2[5811]: I'm the children process, I handle the
endpoint 0x87
When I tried using lynx addresses couldn't be resolved but ifconfig -a reported
that tun0 was up. Its difficult
to do further analysis since using -ddial seems to prompt a system lock up minutes
after using it! If i try pinging
the dns servers i specified in resolv.conf i get the error 'No route to host'
which does look
like the 'add default HISADDR' isn't quite working... certainly that 'add route
failed' warning *always* crops up.
Can anyone see some obvious things im missing?
Many thanks,
Paul
http://uk2.net
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se désinscrire : mailto:[EMAIL PROTECTED]?subject=unsubscribe
