Hello Craig,
Thank for your reply to my message, I have attached some of the info you
requested:
/opt/SUNWut/bin/utxconfig -t pseudo.002128fb08d7 -l
DIMENSIONS=auto
ENABLE_PSEUDOCOLOR_VISUAL=no
DEFAULT_PSEUDOCOLOR_VISUAL=no
ENABLE_MULTISCREEN=yes
ENABLE_XINERAMA=no
ENABLE_XKB=yes
SCREEN_GEOMETRY=auto
SCREEN_ORDER=auto
XSERVER_PREF=Xnewt
QUICK_ABORT=yes
XRENDER=yes
The other commands can't be run right now, because I'm not onsite, and the
operator does not have an Oracle smart card.
Best regards,
Christian Montero H.
>________________________________
> From: Craig Bender <craig.ben...@oracle.com>
>To: sunray-users@filibeto.org
>Sent: Thursday, April 25, 2013 12:45 PM
>Subject: Re: [SunRay-Users] Wrong Screen Size after firmware update to 11.1.1.0
>
>
>What ustresadm command did you use to set it? Unlike utsettings, it's
>pretty sticky, but you have to do it correctly.
>
>If you just type utresadm, what output do you get?
>
>What's the make and model of the monitor?
>
>Can you also provide your utxconfig settings for your token? utxconfig
>-l (run from within your session)
>
>If possible, can you also provide xrandr -q output? (run from withing
>your session)
>
>
>
>
>On 4/25/13 8:30 AM, Christian Montero Hernández wrote:
>>
>> *From:* Jim Klimov <jimkli...@cos.ru>
>> *To:* sunray-users@filibeto.org
>> *Sent:* Thursday, April 25, 2013 11:30 AM
>> *Subject:* Re: [SunRay-Users] Wrong Screen Size after firmware
>> update to 11.1.1.0
>>
>> On 2013-04-25 15:05, Christian Montero Hernández wrote:
>> > Hello everyone,
>> >
>> > I was wondering if there is a default option for this firmware and
>> > screens, because I have an Oracle VDI 3.4.1 deployment and I was
>> using
>> > firmware 11.0.x, but after some time considering an update I
>> tried 1 Sun
>> > Ray 3 with the new firmware and then that Sun Ray 3 always shows a
>> > 1280x1024 resolution instead of the supported by the monitor
>> 1024x768, I
>> > have made a manual change to the screen size, but after a power cycle
>> > the resolution comes back to 1280x1024.
>> >
>> > - Has anyone had this issue before?
>> > - Why the change in behavior between firmware 11.0.x and 11.1.x?
>> >
>> > Thanks in advance for any tip you can give me.
>>
>>
>> You could try utresadm to enforce particular resolution for a particular
>> token (IEEE MAC address of the DTU). BTW, does this also happen if you
>> first power on the display, and then power on (or powercycle) the DTU,
>> that is, when the DTU should already know the display's best supported
>> resolution? Does it happen or change with different display models?
>>
>> HTH,
>> //Jim
>>
>> Hello Jim
>>
>> Thank for your reply to my message, I have tried utresadm, but it works
>> as long as I keep the session alive or the sun ray 3 is still powered on.
>> The display is always on, I never turn it off. (It just sleeps sometimes)
>> If I powercycle the sun ray 3 or if I, for some reason, unplug the power
>> cord the resolution is back to 1280x1024.
>> I have just tried this one Sun Ray 3, I have 5 other Sun Ray 3 but those
>> are in the warehouse.
>> I just did another test with a different screen, this time it was a 15"
>> wide, and the screen resolution was 1280x1024.
>>
>> This afternoon I will try another Sun Ray 3 with those 2 screens and let
>> you know if the behavior was the same or not.
>>
>> Thanks for the help.
>>
>> Best regards,
>>
>> Christian Montero H.
>>
>>
>> _______________________________________________
>> SunRay-Users mailing list
>> SunRay-Users@filibeto.org
>> http://www.filibeto.org/mailman/listinfo/sunray-users
>>
>_______________________________________________
>SunRay-Users mailing list
>SunRay-Users@filibeto.org
>http://www.filibeto.org/mailman/listinfo/sunray-users
>
>
_______________________________________________
SunRay-Users mailing list
SunRay-Users@filibeto.org
http://www.filibeto.org/mailman/listinfo/sunray-users
