Hi John Thanks for your reply. If I configure the counter for compatible mode, then set it up to measure frequency as a 53131/53132 from the "Acquire" menu and press the "Monitor" button, TimeLab displays the actual instrument name and then follows this with line after line of frequency measurements, for example, which so far is looking pretty good. If I then press the "Start Measurement" button it seems that TimeLab requests the instrument ID again but then interprets the reply as an incorrect frequency measurement and reports an error, which I admit isn't quite the same as I suggested earlier. The error message I was seeing was the same, I just didn't interpret it correctly. Until checking again just now I've not had the Monitor window displaying anything either so hadn't realised measurements were actually being accepted at that point. Not sure what I was doing wrong there but I guess the "user issues" might still be very much alive and kicking:-) The messages I get after trying to start the measurement are, in sequence Preparing Acquisition.... Establishing Connection.... Error: Invalid Frequency Value "Tektronix, FCA3100, 149110, V1.28 25 Aug 2010 11:52 and that's where it stops. To be fair to Pendulum they do seem to have implemented talk-only mode, or at least they claim to have and there is a GPIB command to enable it, but so far I don't seem to have been able to get it to switch into that, or if I have I certainly haven't noticed:-) There's several steps described in the manual for invoking talk-only mode and some of those steps I can actually verify as having been accepted as I go along, but still not much sign of streaming data:-( Regards Nigel GM8PZR In a message dated 09/10/2013 22:49:24 GMT Daylight Time, j...@miles.io writes:
TimeLab will capture and display the *IDN? result as the instrument name, but it shouldn't reject the connection if it doesn't get what it expects. How is it behaving when it rejects the data? You've got to wonder what was going through the heads of the designers of the various counters that didn't implement talk-only mode. Of all the obvious useful features to leave out... :( -- john, KE5FX Miles Design LLC > -----Original Message----- > From: time-nuts-boun...@febo.com [mailto:time-nuts- > boun...@febo.com] On Behalf Of gandal...@aol.com > Sent: Wednesday, October 09, 2013 12:32 PM > To: time-nuts@febo.com > Subject: [time-nuts] Pendulum CNT91 with TimeLab > > Has anybody had any success setting up the Pendulum CNT91, or the > Tektronix rebadged equivalent FCA3100, to run with TimeLab? > > It was suggested here some time ago that it should be possible to achieve > this by running the counter in talk only mode but so far I've had no luck > with the FCA3100 and am aware of similar problems with the CNT91. > > I suspect this is more likely a counter issue, or perhaps in my case that > should read "user issue":-) rather than anything to do with the software. > I'm using an NI USB GPIB adapter and can run the FCA3100 with the cut down > Tektronix supplied version of NI's Signal Express, but whilst I can also > talk to it using NI's Measurement and Automation Explorer any attempts > with > that to switch it into talk only mode either don't work or perhaps it's > reverting as soon as I close the software to switch over to TimeLab. > > I've also tried running the counter in GPIB "compatible" mode", where it's > claimed to emulate the SCPI command set of the HP 5313x series, but as far > as I can tell TimeLab is rejecting the data because it checks for a valid > HP ID string whilst the counters still respond as either an FCA3100 or > CNT91. > > Regards > > Nigel > GM8PZR > _______________________________________________ > time-nuts mailing list -- time-nuts@febo.com > To unsubscribe, go to https://www.febo.com/cgi- > bin/mailman/listinfo/time-nuts > and follow the instructions there. _______________________________________________ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. _______________________________________________ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.