I have a similar problem with my PCMCIA card....it worked perfectly under 8.04 but now cannot see the router.
Here is a printout: [EMAIL PROTECTED]:~$ sudo lshw -C Network *-network description: Ethernet interface product: 3c556B CardBus [Tornado] vendor: 3Com Corporation physical id: 3 bus info: [EMAIL PROTECTED]:00:03.0 logical name: eth0 version: 20 serial: 00:04:76:60:6f:87 size: 10MB/s capacity: 100MB/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=3c59x duplex=half latency=64 link=no maxlatency=10 mingnt=10 module=3c59x multicast=yes port=MII speed=10MB/s *-network DISABLED description: Wireless interface product: ACX 111 54Mbps Wireless Interface vendor: Texas Instruments physical id: 1 bus info: [EMAIL PROTECTED]:06:00.0 logical name: wlan0 version: 00 serial: 00:0f:3d:57:76:56 width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=acx_pci latency=64 module=acx multicast=yes wireless=IEEE 802.11b+/g+ *-network DISABLED description: Ethernet interface physical id: 1 logical name: pan0 serial: d2:f8:de:93:ae:85 capabilities: ethernet physical configuration: broadcast=yes driver=bridge driverversion=2.3 firmware=N/A link=yes multicast=yes [EMAIL PROTECTED]:~$ lspci -nn 00:00.0 Host bridge [0600]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge [8086:7190] (rev 03) 00:01.0 PCI bridge [0604]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge [8086:7191] (rev 03) 00:02.0 CardBus bridge [0607]: Texas Instruments PCI1450 [104c:ac1b] (rev 03) 00:02.1 CardBus bridge [0607]: Texas Instruments PCI1450 [104c:ac1b] (rev 03) 00:03.0 Ethernet controller [0200]: 3Com Corporation 3c556B CardBus [Tornado] [10b7:6056] (rev 20) 00:03.1 Communication controller [0780]: 3Com Corporation Mini PCI 56k Winmodem [10b7:1007] (rev 20) 00:05.0 Multimedia audio controller [0401]: Cirrus Logic CS 4614/22/24/30 [CrystalClear SoundFusion Audio Accelerator] [1013:6003] (rev 01) 00:07.0 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ISA [8086:7110] (rev 02) 00:07.1 IDE interface [0101]: Intel Corporation 82371AB/EB/MB PIIX4 IDE [8086:7111] (rev 01) 00:07.2 USB Controller [0c03]: Intel Corporation 82371AB/EB/MB PIIX4 USB [8086:7112] (rev 01) 00:07.3 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ACPI [8086:7113] (rev 03) 01:00.0 VGA compatible controller [0300]: S3 Inc. 86C270-294 Savage/IX-MV [5333:8c12] (rev 13) 06:00.0 Network controller [0280]: Texas Instruments ACX 111 54Mbps Wireless Interface [104c:9066] [EMAIL PROTECTED]:~$ dmseg | grep -e iwl -e wlan -e rt -e ath bash: dmseg: command not found [EMAIL PROTECTED]:~$ dmesg | grep -e iwl -e wlan -e rt -e ath [ 0.000000] Movable zone start PFN for each node [ 0.000000] ACPI: PM-Timer IO Port: 0x1008 [ 0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:dff80000) [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.004000] virtual kernel memory layout: [ 0.881353] Booting paravirtualized kernel on bare hardware [ 1.365536] ACPI: (supports S0 S1 S3 S4 S5) [ 1.626629] ACPI: EC: driver started in interrupt mode [ 1.628743] pci 0000:00:02.0: supports D1 [ 1.628753] pci 0000:00:02.0: supports D2 [ 1.628764] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1.628864] pci 0000:00:02.1: supports D1 [ 1.628873] pci 0000:00:02.1: supports D2 [ 1.628883] pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold [ 1.628959] PCI: 0000:00:03.0 reg 10 io port: [1800, 18ff] [ 1.629065] pci 0000:00:03.0: supports D1 [ 1.629074] pci 0000:00:03.0: supports D2 [ 1.629085] pci 0000:00:03.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1.629149] PCI: 0000:00:03.1 reg 10 io port: [2000, 20ff] [ 1.629243] pci 0000:00:03.1: supports D2 [ 1.629254] pci 0000:00:03.1: PME# supported from D0 D2 D3hot D3cold [ 1.629413] pci 0000:00:05.0: supports D1 [ 1.629422] pci 0000:00:05.0: supports D2 [ 1.629561] PCI: 0000:00:07.1 reg 20 io port: [1c00, 1c0f] [ 1.629659] PCI: 0000:00:07.2 reg 20 io port: [1c20, 1c3f] [ 1.630050] pci 0000:01:00.0: supports D1 [ 1.630060] pci 0000:01:00.0: supports D2 [ 1.672879] Linux Plug and Play Support v0.97 (c) Adam Belay [ 1.804694] system 00:02: ioport range 0x1000-0x103f has been reserved [ 1.804709] system 00:02: ioport range 0x1040-0x104f has been reserved [ 1.804725] system 00:02: ioport range 0xfe00-0xfe0f has been reserved [ 1.804778] system 00:09: ioport range 0x15e0-0x15ef has been reserved [ 1.848667] bus: 00 index 0 io port: [0, ffff] [ 1.848730] bus: 02 index 0 io port: [1400, 14ff] [ 1.848741] bus: 02 index 1 io port: [2400, 24ff] [ 1.848774] bus: 06 index 0 io port: [2800, 28ff] [ 1.848784] bus: 06 index 1 io port: [2c00, 2cff] [ 4.290293] Serial: 8250/16550 driver4 ports, IRQ sharing enabled [ 4.320603] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 4.320626] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 4.322535] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0 [ 4.322574] rtc0: alarms up to one month, y3k [ 4.324893] Using IPI No-Shortcut mode [ 4.326596] rtc_cmos 00:06: setting system clock to 2008-10-06 04:22:17 UTC (1223266937) [ 5.088224] ACPI: Processor [CPU] (supports 8 throttling states) [ 9.120280] hub 1-0:1.0: 2 ports detected [ 10.154015] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 10.154465] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 10.567610] PM: Starting manual resume from disk [ 10.567621] PM: Resume from partition 8:5 [ 12.666097] kjournald starting. Commit interval 5 seconds [ 21.187337] udevd version 124 started [ 26.820514] Linux agpgart interface v0.103 [ 27.212981] agpgart-intel 0000:00:00.0: Intel 440BX Chipset [ 27.217766] agpgart-intel 0000:00:00.0: AGP aperture is 64M @ 0xf8000000 [ 28.460097] pccard: CardBus card inserted into slot 1 [ 28.460229] pci 0000:06:00.0: supports D1 [ 28.460234] pci 0000:06:00.0: supports D2 [ 28.460241] pci 0000:06:00.0: PME# supported from D0 D1 D2 D3hot [ 32.556727] parport_pc 00:0d: reported by Plug and Play ACPI [ 32.556793] parport0: PC-style at 0x3bc, irq 7 [PCSPP,TRISTATE] [ 32.991458] cs: IO port probe 0x100-0x3af: clean. [ 32.992312] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7 [ 32.992686] cs: IO port probe 0x820-0x8ff: clean. [ 32.993005] cs: IO port probe 0xc00-0xcf7: clean. [ 32.993539] cs: IO port probe 0xa00-0xaff: clean. [ 32.994533] cs: IO port probe 0x100-0x3af: clean. [ 32.995329] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7 [ 32.995700] cs: IO port probe 0x820-0x8ff: clean. [ 32.996070] cs: IO port probe 0xc00-0xcf7: clean. [ 32.996601] cs: IO port probe 0xa00-0xaff: clean. [ 33.500414] acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them [ 35.152573] CCAModes:04 Diversity:01 ShortPreOpt:01 PBCC:01 ChanAgil:00 PHY:05 Temp:01 [ 35.217762] acx v0.3.36: net device wlan0, driver compiled against wireless extensions 22 and Linux 2.6.27-5-generic [ 35.884713] gameport: CS46xx Gameport is pci0000:00:05.0/gameport0, speed 1704kHz [ 37.563759] lp0: using parport0 (interrupt-driven). [ 47.286106] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use) [ 47.960304] ppdev: user-space parallel port driver [ 87.494434] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 99.888081] wlan0: issue_cmd(): timed out waiting for CMD_COMPLETE. irq bits:0x0000 irq_status:0x0000 timeout:49ms cmd_status:1 (Success) [ 99.888104] wlan0: issue_cmd(cmd:0x0002) FAILED [ 99.888746] wlan0: configure(type:0x1010) FAILED [ 103.524089] wlan0: issue_cmd(): timed out waiting for CMD_COMPLETE. irq bits:0x0000 irq_status:0x0000 timeout:49ms cmd_status:1 (Success) [ 103.524112] wlan0: issue_cmd(cmd:0x0016) FAILED [ 106.908104] wlan0: issue_cmd(): timed out waiting for CMD_COMPLETE. irq bits:0x0000 irq_status:0x0000 timeout:49ms cmd_status:1 (Success) [ 106.908128] wlan0: issue_cmd(cmd:0x0016) FAILED [ 119.836066] wlan0: issue_cmd(): timed out waiting for CMD_COMPLETE. irq bits:0x0000 irq_status:0x0000 timeout:49ms cmd_status:1 (Success) [ 119.836090] wlan0: issue_cmd(cmd:0x0016) FAILED [ 154.696069] wlan0: issue_cmd(): timed out waiting for CMD_COMPLETE. irq bits:0x0000 irq_status:0x0000 timeout:49ms cmd_status:1 (Success) [ 154.696093] wlan0: issue_cmd(cmd:0x0016) FAILED [ 160.924118] wlan0: issue_cmd(): timed out waiting for CMD_COMPLETE. irq bits:0x0000 irq_status:0x0000 timeout:49ms cmd_status:1 (Success) [ 160.924144] wlan0: issue_cmd(cmd:0x0016) FAILED [ 163.780079] wlan0: issue_cmd(): timed out waiting for CMD_COMPLETE. irq bits:0x0000 irq_status:0x0000 timeout:49ms cmd_status:1 (Success) [ 163.780104] wlan0: issue_cmd(cmd:0x0016) FAILED [ 180.072116] wlan0: issue_cmd(): timed out waiting for CMD_COMPLETE. irq bits:0x0000 irq_status:0x0000 timeout:49ms cmd_status:1 (Success) [ 180.072149] wlan0: issue_cmd(cmd:0x0016) FAILED [ 193.476114] wlan0: issue_cmd(): timed out waiting for CMD_COMPLETE. irq bits:0x0000 irq_status:0x0000 timeout:49ms cmd_status:1 (Success) [ 193.476138] wlan0: issue_cmd(cmd:0x0016) FAILED [ 200.624095] wlan0: issue_cmd(): timed out waiting for CMD_COMPLETE. irq bits:0x0000 irq_status:0x0000 timeout:49ms cmd_status:1 (Success) [ 200.624118] wlan0: issue_cmd(cmd:0x0016) FAILED [ 216.296076] wlan0: issue_cmd(): timed out waiting for CMD_COMPLETE. irq bits:0x2000 irq_status:0x2000 timeout:49ms cmd_status:1 (Success) [ 216.296100] wlan0: issue_cmd(cmd:0x0016) FAILED [ 225.488076] wlan0: issue_cmd(): timed out waiting for CMD_COMPLETE. irq bits:0x0000 irq_status:0x0000 timeout:49ms cmd_status:1 (Success) [ 225.488101] wlan0: issue_cmd(cmd:0x0016) FAILED [ 225.680067] wlan0: issue_cmd(): timed out waiting for CMD_COMPLETE. irq bits:0x0000 irq_status:0x0000 timeout:49ms cmd_status:1 (Success) [ 225.680091] wlan0: issue_cmd(cmd:0x0016) FAILED [EMAIL PROTECTED]:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:04:76:60:6f:87 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:11 Base address:0x4400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:226 errors:0 dropped:0 overruns:0 frame:0 TX packets:226 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:11300 (11.3 KB) TX bytes:11300 (11.3 KB) [EMAIL PROTECTED]:~$ sudo iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. irda0 Interface doesn't support scanning. wlan0 Interface doesn't support scanning : Resource temporarily unavailable pan0 Interface doesn't support scanning. Obviously my wireless card is not "seeing" my router. The internal card on my Dell can see it no problem and this card could see it when I was using KDE 4.1. [EMAIL PROTECTED]:~$ sudo ifconfig wlan0 up [sudo] password for fitz: wlan0: ERROR while getting interface flags: No such device [EMAIL PROTECTED]:~$ sudo iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. irda0 Interface doesn't support scanning. pan0 Interface doesn't support scanning. [EMAIL PROTECTED]:~$ lshw -C Network WARNING: you should run this program as super-user. *-network description: Ethernet interface product: 3c556B CardBus [Tornado] vendor: 3Com Corporation physical id: 3 bus info: [EMAIL PROTECTED]:00:03.0 logical name: eth0 version: 20 serial: 00:04:76:60:6f:87 width: 32 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical configuration: broadcast=yes driver=3c59x ip=10.1.1.6 latency=64 maxlatency=10 mingnt=10 module=3c59x multicast=yes *-network DISABLED description: Ethernet interface physical id: 1 logical name: pan0 serial: d6:6f:77:08:a1:b4 capabilities: ethernet physical configuration: broadcast=yes driver=bridge driverversion=2.3 firmware=N/A multicast=yes -- [intrepid-beta] PCMCIA network-card working in hardy does not work https://bugs.launchpad.net/bugs/278350 You received this bug notification because you are a member of Ubuntu Bugs, which is subscribed to Ubuntu. -- ubuntu-bugs mailing list ubuntu-bugs@lists.ubuntu.com https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
