Hi Christophe, I've been reading the thread but I think your configuration looks correct. Can you give it a shot at using VNC to see if the VM is booting up correctly? Maybe there's a problem with the VM...
Add the following to your ONE template: GRAPHICS = [ TYPE = "vnc", LISTEN = "0.0.0.0", PORT = "5900"] Start the VM and connect to it via a VNC client (for instance vncviewer). Inspect the VM to see if there's a problem with it. Regards, Jaime On Wed, Dec 15, 2010 at 4:47 PM, Christophe Hamerling - Petals Link <christophe.hamerl...@petalslink.com> wrote: > I am wondering if the problem does not also comes from the virtual network > configuration. > Here is my configuration : > I am at home, my LAN address is 192.168.2.0/255.255.255.0 . GW is > 192.168.2.1 > My front address is 192.168.2.60 and the node one is 192.168.2.61 > I tried to setup a bridge on the node, it seems to work (refer to my > previous mails). > I try to create a VM and to reach it at 192.168.2.71 but I am wondering now > if it is possible to access a VM network from my laptop for exemple? How can > I say to opennebula that I want to 'publish' VMs on my LAN? Is PUBLIC = YES > is enough in the network configuration file? Do I need to put the front as a > gateway somewhere, or another host? > Thanks a lot > Christophe > > On Wed, Dec 15, 2010 at 3:59 PM, Christophe Hamerling - Petals Link > <christophe.hamerl...@petalslink.com> wrote: >> >> Is there a link between the MAC address defined in the VM and with the >> ones listed with ifconfig on the node? I do not have any. >> >> On Wed, Dec 15, 2010 at 3:46 PM, Christophe Hamerling - Petals Link >> <christophe.hamerl...@petalslink.com> wrote: >>> >>> Is there a web page where the network configuration on front and nodes is >>> described? The only thing that I can find is >>> at http://marianmi.comp.nus.edu.sg/2010/08/opennebula-installation-and-configuration-guide.php >>> I really think that it is a network configuration problem. Here is what I >>> did : >>> Front : eth0 = 192.168.2.60 >>> On the Node : br0 = 192.168.2.61 >>> The gateway defined to 192.168.2.60, not sure about that. Using my >>> internet box as gateway does not work too. >>> I defined a LEASES address out of my DHCP range. >>> When the VM is starting, I can see on the node a new network interface >>> named vnet0 with the same mac address of my bridge. Is it ok? >>> Before the VM start, the br0 mac address is the same as eth0... Is this a >>> normal behaviour? >>> Here is my ifconfig log >>> br0 Link encap:Ethernet HWaddr 00:ff:da:72:02:21 >>> inet adr:192.168.2.61 Bcast:192.168.2.255 >>> Masque:255.255.255.0 >>> adr inet6: fe80::a00:27ff:fed7:f0fd/64 Scope:Lien >>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >>> RX packets:787 errors:0 dropped:0 overruns:0 frame:0 >>> TX packets:500 errors:0 dropped:0 overruns:0 carrier:0 >>> collisions:0 lg file transmission:0 >>> RX bytes:126978 (124.0 KiB) TX bytes:81984 (80.0 KiB) >>> eth0 Link encap:Ethernet HWaddr 08:00:27:d7:f0:fd >>> adr inet6: fe80::a00:27ff:fed7:f0fd/64 Scope:Lien >>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >>> RX packets:1268 errors:0 dropped:0 overruns:0 frame:0 >>> TX packets:506 errors:0 dropped:0 overruns:0 carrier:0 >>> collisions:0 lg file transmission:1000 >>> RX bytes:188739 (184.3 KiB) TX bytes:82452 (80.5 KiB) >>> lo Link encap:Boucle locale >>> inet adr:127.0.0.1 Masque:255.0.0.0 >>> adr inet6: ::1/128 Scope:Hôte >>> UP LOOPBACK RUNNING MTU:16436 Metric:1 >>> RX packets:28 errors:0 dropped:0 overruns:0 frame:0 >>> TX packets:28 errors:0 dropped:0 overruns:0 carrier:0 >>> collisions:0 lg file transmission:0 >>> RX bytes:2156 (2.1 KiB) TX bytes:2156 (2.1 KiB) >>> vnet0 Link encap:Ethernet HWaddr 00:ff:da:72:02:21 >>> adr inet6: fe80::2ff:daff:fe72:221/64 Scope:Lien >>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0 >>> TX packets:226 errors:0 dropped:0 overruns:0 carrier:0 >>> collisions:0 lg file transmission:500 >>> RX bytes:0 (0.0 B) TX bytes:38791 (37.8 KiB) >>> >>> >>> >>> On Wed, Dec 15, 2010 at 11:37 AM, Gian Uberto Lauri <sa...@eng.it> wrote: >>>>>>>>> >>>>>>>>> "CH" == Christophe Hamerling <- Petals Link >>>>>>>>> <christophe.hamerl...@petalslink.com>> writes: >>>> >>>> CH> Ok, so I will check that the generated IP is the one expected from >>>> CH> the leases list based on this script algorithm. Is the VM is >>>> CH> exploded somewhere at startup? If yes, where? >>>> >>>> No, it is not. >>>> >>>> A _new_, temporary "cd image" is created on the fly and mounted at the >>>> first boot, AFAIK. >>>> >>>> -- >>>> ing. Gian Uberto Lauri >>>> Ricercatore / Reasearcher >>>> Divisione Ricerca ed Innovazione / Research & Innovation Division >>>> gianuberto.la...@eng.it >>>> >>>> Engineering Ingegneria Informatica spa >>>> Corso Stati Uniti 23/C, 35127 Padova (PD) >>>> >>>> Tel. +39-049.8283.538 | main(){printf(&unix["\021%six\012\0"], >>>> Fax +39-049.8283.569 | (unix)["have"]+"fun"-0x60);} >>>> Skype: gian.uberto.lauri | David Korn, AT&T Bell Labs >>>> http://www.eng.it | ioccc best One >>>> Liner, 1987 >>>> >>>> >>>> _______________________________________________ >>>> Users mailing list >>>> Users@lists.opennebula.org >>>> http://lists.opennebula.org/listinfo.cgi/users-opennebula.org >>> >>> >>> >>> -- >>> Christophe Hamerling >>> R&D Engineer & Project Leader >>> Petals Link - SOA open-source company >>> OW2 PEtALS SOA Suite Comitter >>> Skype : christophe.hamerling >>> Jabber : chamerl...@jabber.org >>> Blog : http://chamerling.org >> >> >> >> -- >> Christophe Hamerling >> R&D Engineer & Project Leader >> Petals Link - SOA open-source company >> OW2 PEtALS SOA Suite Comitter >> Skype : christophe.hamerling >> Jabber : chamerl...@jabber.org >> Blog : http://chamerling.org > > > > -- > Christophe Hamerling > R&D Engineer & Project Leader > Petals Link - SOA open-source company > OW2 PEtALS SOA Suite Comitter > Skype : christophe.hamerling > Jabber : chamerl...@jabber.org > Blog : http://chamerling.org > > _______________________________________________ > Users mailing list > Users@lists.opennebula.org > http://lists.opennebula.org/listinfo.cgi/users-opennebula.org > > -- Jaime Melis, Cloud Technology Engineer/Researcher DSA Research Group: web http://dsa-research.org and blog http://blog.dsa-research.org OpenNebula Open Source Toolkit for Cloud Computing: http://www.OpenNebula.org _______________________________________________ Users mailing list Users@lists.opennebula.org http://lists.opennebula.org/listinfo.cgi/users-opennebula.org