Hi, Gregoire Favre wrote:
>> To just prove my understanding: >> Your VDR is able to switch to all three satelites, but from time to time >> you get those tuning timeouts. Reloading the drivers fixes this issue >> and VDR can then switch to all three satellites again. > > More or less : it's slow (compared to kaffeine) and when I use vdr with > only one card, I can choose the sat in vdr, but then under kaffeine with > the two others cards, I can't tune to another sat than the same choosen > in VDR ??? > > In kaffeine, I can reccord without problem on three differents sats. I do not see how the ports could interfere with each other. Your switch provides 4 independent 1-of-3 switches and each of your 3 LNBs provides 4 independent 1-of-4 switches. >>>> Hhm, these settings only help in determining high/low band and the >>>> frequency to tune to. I first need to take a look into the code how >>>> kaffeine and xine-lib pass the information about the port to use to the >>>> DVB driver. >> >> Haven't had a look at this yet. > > Here kaffeine output of some tuning : > > Tuning to: ARTE / autocount: 11 > Using DVB device 0:0 "ST STV0299 DVB-S" > tuning DVB-S to 11567000 v 22000000 > inv:2 fecH:5 > DiSEqC: switch pos 0, 13V, loband (index 0) > DiSEqC: e0 10 38 f0 00 00 I've had a look at the source code today. kaffeine "uses" a VDR diseqc.conf like this one: S19.2E 11700 V 9750 t v W15 [E0 10 38 F0] W15 A W15 t S19.2E 99999 V 10600 t v W15 [E0 10 38 F1] W15 A W15 T S19.2E 11700 H 9750 t V W15 [E0 10 38 F2] W15 A W15 t S19.2E 99999 H 10600 t V W15 [E0 10 38 F3] W15 A W15 T S13.0E 11700 V 9750 t v W15 [E0 10 38 F4] W15 B W15 t S13.0E 99999 V 10600 t v W15 [E0 10 38 F5] W15 B W15 T S13.0E 11700 H 9750 t V W15 [E0 10 38 F6] W15 B W15 t S13.0E 99999 H 10600 t V W15 [E0 10 38 F7] W15 B W15 T S28.2E 11700 V 9750 t v W15 [E0 10 38 F8] W15 A W15 t S28.2E 99999 V 10600 t v W15 [E0 10 38 F9] W15 A W15 T S28.2E 11700 H 9750 t V W15 [E0 10 38 FA] W15 A W15 t S28.2E 99999 H 10600 t V W15 [E0 10 38 FB] W15 A W15 T I also had a closer look into the specification and into the implementation guide. There is only one mandatory command for DiSEqC 1.0: the above used 0x38. Bye. -- Dipl.-Inform. (FH) Reinhard Nissl mailto:[EMAIL PROTECTED] _______________________________________________ vdr mailing list vdr@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr
