Hi zd1211 community,
one step closer to the zd1211rw. Somehow i have to unplug and plug in
my usb dongle to my computer, unless the driver can probe on it. i
didn't even touched the firmware files, which are still installed and
unchanged since last time i posted.
now i get some more closer to get the driver working, my dongle is being
detected, i can configure my wlan (wep 128bit, ip-address ...) but i
cannot connect to it.
here some output to make things clear:
when i boot my pc, the driver loads, but my wlan card is just off (no led)
(i'm using the ohci_hcd driver for my ov511 webcam, this shouldn't be a
problem i guess)
ohci_hcd 0000:00:02.1: OHCI Host Controller
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.1: irq 18, io mem 0xf5005000
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.17-rc4-mm3 ohci_hcd
usb usb2: SerialNumber: 0000:00:02.1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
Linux agpgart interface v0.101 (c) Dave Jones
usb 2-3: new full speed USB device using ohci_hcd and address 2
agpgart: Detected AGP bridge 0
agpgart: Setting up Nforce3 AGP.
agpgart: AGP aperture is 32M @ 0xf0000000
ieee80211_crypt: registered algorithm 'NULL'
usb 2-3: new device found, idVendor=0ace, idProduct=1211
usb 2-3: new device strings: Mfr=16, Product=32, SerialNumber=0
usb 2-3: Product: USB2.0 WLAN
usb 2-3: Manufacturer: ZyDAS
usb 2-3: configuration #1 chosen from 1 choice
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation
<[EMAIL PROTECTED]>
usb 2-4: new full speed USB device using ohci_hcd and address 3
usb 2-4: new device found, idVendor=05a9, idProduct=a518
usb 2-4: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-4: Product: USB Camera
usb 2-4: Manufacturer: OmniVision Technologies, Inc.
usb 2-4: configuration #1 chosen from 1 choice
Linux video capture interface: v1.00
usb 2-3: firmware device id 0x4330 and actual device id 0x4810 differ,
continuing anyway
firmware_loading_store: unexpected value (0)
usb 2-3: reset full speed USB device using ohci_hcd and address 2
usb 2-3: device descriptor read/64, error -110
usb 2-3: device descriptor read/64, error -110
usb 2-3: reset full speed USB device using ohci_hcd and address 2
usb 2-3: device descriptor read/64, error -110
usb 2-3: device descriptor read/64, error -110
usb 2-3: reset full speed USB device using ohci_hcd and address 2
---- about here i replugged my usb dongle -----
usb 2-3: device not accepting address 2, error -110
zd1211rw: probe of 2-3:1.0 failed with error -110
usb 2-3: USB disconnect, address 2
usbcore: registered new driver zd1211rw
/usr/src/ov511-2.32/ov511_core.c: USB OV518+ video device found
/usr/src/ov511-2.32/ov511_core.c: Device revision 0
/usr/src/ov511-2.32/ov511_core.c: Compression required with OV518...enabling
/usr/src/ov511-2.32/ovcamchip_core.c: v2.32 : OV camera chip I2C driver
/usr/src/ov511-2.32/ovcamchip_core.c: Camera chip is an OV7620AE
/usr/src/ov511-2.32/ov511_core.c: Device at usb-0000:00:02.1-4
registered to minor 0
usbcore: registered new driver ov511
/usr/src/ov511-2.32/ov511_core.c: v2.32 : ov511 USB Camera Driver (V4L2
disabled)
nvidia: module license 'NVIDIA' taints kernel.
ACPI (acpi_bus-0192): Device `VGAG]is not power manageable [20060310]
ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16
GSI 19 sharing vector 0xC9 and IRQ 19
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [APC5] -> GSI 16 (level,
low) -> IRQ 19
NVRM: loading NVIDIA Linux x86_64 Kernel Module 1.0-8762 Mon May 15
13:58:14 PDT 2006
usb 2-3: new full speed USB device using ohci_hcd and address 4
usb 2-3: new device found, idVendor=0ace, idProduct=1211
usb 2-3: new device strings: Mfr=16, Product=32, SerialNumber=0
usb 2-3: Product: USB2.0 WLAN
usb 2-3: Manufacturer: ZyDAS
usb 2-3: configuration #1 chosen from 1 choice
usb 2-3: firmware device id 0x4330 and actual device id 0x4810 differ,
continuing anyway
zd1211rw 2-3:1.0: firmware version 4605
zd1211rw 2-3:1.0: zd1211 chip 0ace:1211 v4810 full 00-11-e2 AL2230_RF
pa0 ---
zd1211rw 2-3:1.0: eth0
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x1c00
i2c_adapter i2c-2: nForce2 SMBus adapter at 0x2000
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (4095 buckets, 32760 max) - 304 bytes per conntrack
ieee80211_crypt: registered algorithm 'WEP'
zd1211rw 2-3:1.0: error ioread32(CR_REG1): -11
SoftMAC: Authentication response received from 00:03:c9:a3:xx:xx but no
queue item exists.
i just copied the whole dmesg to make things easier, if there are any
hardware questions.
I think the last two lines are the most important ones to you.
i use the following commands to connect to my ap:
ifconfig eth0 up
iwconfig eth0 essid "WLAN"
iwconfig eth0 mode managed
iwconfig eth0 rate auto
iwconfig eth0 key restricted xxxxxxxxxxxxxxxxxxxxxxxxxx [1]
iwconfig eth0 key restricted xxxxxxxxxxxxxxxxxxxxxxxxxx [2]
ifconfig eth0 192.168.2.155 netmask 255.255.255.0 up
route add default gw 192.168.2.1
Any help will be appreciated.
So long
Christian
Daniel Drake wrote:
> C.S: wrote:
>> Hello zd1211 community,
>>
>> my first steps on the zd1211rw were pretty bad.
>> showing dmesg at reboot shows why:
>>
>> usb 1-4: device descriptor read/64, error -110
>> usb 1-4: device descriptor read/64, error -110
>> usb 1-4: new full speed USB device using ohci_hcd and address 3
>> usb 1-4: device descriptor read/64, error -110
>> usb 1-4: device descriptor read/64, error -110
>> usb 1-4: new full speed USB device using ohci_hcd and address 4
>> usb 1-4: device not accepting address 4, error -110
>> usb 1-4: new full speed USB device using ohci_hcd and address 5
>> usb 1-4: device not accepting address 5, error -110
>> usb 2-4: new full speed USB device using ohci_hcd and address 2
>> usb 2-4: new device found, idVendor=05a9, idProduct=a518
>> usb 2-4: new device strings: Mfr=1, Product=2, SerialNumber=0
>> usb 2-4: Product: USB Camera
>> usb 2-4: Manufacturer: OmniVision Technologies, Inc.
>> usb 2-4: configuration #1 chosen from 1 choice
>
> This is not related to zd1211rw, the driver was never activated since
> the computer couldn't even identify the device. You will almost
> certainly have the same problem with the vendor driver.
>
>> usb 1-4: request_fw_file() fw name zd1211/zd1211_ub
>> usb 1-4: firmware device id 0x4330 and actual device id 0x4810 differ,
>> continuing anyway
>> usb 1-4: request_fw_file() fw name zd1211/zd1211_uphr
>> firmware_loading_store: unexpected value (0)
>> usb 1-4: Could not load firmware file zd1211/zd1211_uphr. Error
>> number -2
>> zd1211rw 1-4:1.0: couldn't load firmware. Error number -2
>> usb 1-4: reset full speed USB device using ohci_hcd and address 6
>> zd1211rw: probe of 1-4:1.0 failed with error -2
>> usbcore: registered new driver zd1211rw
>> zd1211rw initialized
>
> Did you install the firmware distribution?
>
> Thanks,
> Daniel
>
___________________________________________________________
Telefonate ohne weitere Kosten vom PC zum PC: http://messenger.yahoo.de
_______________________________________________
Zd1211-devs mailing list - http://zd1211.ath.cx/
Unsubscribe: https://lists.sourceforge.net/lists/listinfo/zd1211-devs
