Hi All
Thanks for the replies.
Here is output from HWinfo:
***********************************
hwinfo --sound
09: PCI 108.0: 0401 Multimedia audio controller
[Created at pci.296]
UDI: /org/freedesktop/Hal/devices/pci_10ee_3fc4
Unique ID: 75Hn.ZEKAtBTA_DA
Parent ID: RE4e.huihPTgjou6
SysFS ID: /devices/pci0000:00/0000:00:08.0/0000:01:08.0
SysFS BusID: 0000:01:08.0
Hardware Class: sound
Model: "Xilinx RME Digi9652 (Hammerfall)"
Vendor: pci 0x10ee "Xilinx Corporation"
Device: pci 0x3fc4 "RME Digi9652 (Hammerfall)"
Revision: 0x03
Driver: "RME Digi9652 (Hammerfall)"
Driver Modules: "snd_rme9652"
Memory Range: 0xf9000000-0xf9ffffff (rw,non-prefetchable)
IRQ: 19 (no events)
Module Alias: "pci:v000010EEd00003FC4sv00000000sd00000000bc04sc01i00"
Driver Info #0:
Driver Status: snd_rme9652 is active
Driver Activation Cmd: "modprobe snd_rme9652"
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #24 (PCI bridge)
************************************************
I still cannot get HDSP conf or mixer to open, which means I cannot lock the
card with the DDX.
Unfortunately I cannot move the card to another slot as the video card is
blocking it!
Cheers
All
On 17 September 2010 20:32, Ralf Mardorf <[email protected]> wrote:
> On Fri, 2010-09-17 at 19:14 +0100, Frank Smith wrote:
> > Hi
> > How do I re-install the sound driver when changing the RME card.
> > I have gone back to a 9632 with 3 ADATs
> >
> > Thing is even when un-installing alsa firmware and re-installing it it
> > still shows the original card.
> >
> > I had a problem with ADAT 1 not locking at all, after much testing and
> > changing light pipes I have to assume that
> > the card must be faulty.
> >
> > So I need to tell the system that the card has changed.
> >
> > Here is some output:
> >
> > *******************************
> > sudo hdsploader
> > hdsploader - firmware loader for RME Hammerfall DSP cards
> > Looking for HDSP + Multiface or Digiface cards :
> > Card 0 : RME Digi9652 (Rev 1.5) at 0xf9000000, irq 19
> > *******************************
> >
> > As you can see it seems to think it's the old card.
> > HDSPconf will not open at all or HDSPmixer.
> >
> > When running in the terminal I get:
> >
> > ****************************
> > Looking for HDSP cards :
> > Card 0 : RME Digi9652 (Rev 1.5) at 0xf9000000, irq 19
> > No Hammerfall DSP card found.
> > stu...@64studio:~$
> > ****************************
> >
> >
> > Any ideas how I Load the correct drivers, or must I re-install the
> > OS?
> >
> > Cheers
> > Bob
>
> Hi Bob :)
>
> I've got no knowledge about your issue, but reinstalling 64 Studio
> shouldn't be needed.
>
> Is there an entry in /etc/modprobe.d/alsa-base?
>
> What information do you get after installing hwinfo and running hwinfo
> --sound?
>
> We always should keep a backup of the Linux we are using today, to be
> able to restore it, if it will be broken tomorrow.
>
> - Ralf
>
>
_______________________________________________
64studio-users mailing list
[email protected]
http://lists.64studio.com/mailman/listinfo/64studio-users
