Hello Viraj. I am trying the steps you have suggested. another thing I have noticed is that when you keep the automatic corrections disabled, such mistakes are also reduced. regards.
On 2/17/08, Viraj <[EMAIL PROTECTED]> wrote: > > One thing I forgot to mention. Having edited the corrections list, be sure > to apply it in the document by clicking Apply Corrections in the Tools > menu. > You'll get the option only when a file is open. > ----- Original Message ----- > From: "Viraj" <[EMAIL PROTECTED]> > To: <[email protected]> > Sent: Sunday, February 17, 2008 11:03 AM > Subject: Re: [AI] strange problem with k1000. > > > >I have faced such problems even in earlier versions and have been unable > to > >come up with definite solutions. However, one can try the following: > > > > 1. Switch to Fine reader engine if one is using RTK or Scansoft. > > 2. Try switching to Grey Scanning mode. > > 3. Click Edit Corrections in the Tools menu, press Add, enter the word > as > > it is being recognised, such as, odier, and press OK. Now enter the > > correct word, (other in this instance). Edit all other words that often > > gets misrecognised in the same way. But sometimes this can result in the > > replacement of actually correct words with wrong words. For instance, if > > the program learns to recognise all di as th, then actual words with di > > will also be converted into th (like the word die will be converted into > > the). However, what one can do (though it does not guarantee 100 per > cent > > success) is to enter the entire word in the edit corrections list, > instead > > of letter combination, for instance, odier and other instead of di and > th. > > 4. One can also try the Replace All command (control H). But here also > one > > should be careful to replace the entire wrong word instead of letter > > combinations, else one will get wrong results. one can try enabling the > > Match Whole Word option in the Rplace dialogue box. > > > > One can never hope that issues wil be resolved for good through these > > steps, but one can always try. > > > > Please note that the menu commands described above are based on > > version 9. Look around if version 11 has different menu arangements. > > ----- Original Message ----- > > From: "Mahesh Panicker" <[EMAIL PROTECTED]> > > To: <[email protected]> > > Sent: Saturday, February 16, 2008 9:48 PM > > Subject: [AI] strange problem with k1000. > > > > > >> Hi list. > >> I am facing a strange problem with Kurzweil1000 version 11. when I scan > a > >> document, the letter combination TH gets recognized as DI. for EG, the > >> word > >> that gets recognized as diat. > >> what can be the sorce of this particular problem? how can it be > >> addressed? > >> looking forward to your suggestions. > >> thanks in advance. > >> > >> > >> -- > >> Mahesh S. Panicker > >> room no. 121; > >> Kaveri-hostel; > >> Jawaharlal Nehru university new delhi 110067 india. > >> To unsubscribe send a message to [EMAIL PROTECTED] > >> with the subject unsubscribe. > >> > >> To change your subscription to digest mode or make any other changes, > >> please visit the list home page at > >> > >> > http://accessindia.org.in/mailman/listinfo/accessindia_accessindia.org.in > > > > > To unsubscribe send a message to [EMAIL PROTECTED] the subject unsubscribe. > > To change your subscription to digest mode or make any other changes, > please visit the list home page at > http://accessindia.org.in/mailman/listinfo/accessindia_accessindia.org.in > -- Mahesh S. Panicker room no. 121; Kaveri-hostel; Jawaharlal Nehru university new delhi 110067 india. To unsubscribe send a message to [EMAIL PROTECTED] with the subject unsubscribe. To change your subscription to digest mode or make any other changes, please visit the list home page at http://accessindia.org.in/mailman/listinfo/accessindia_accessindia.org.in
