That's usually indicative of a hardware error. If you're in AIX run the errpt -a command (pipe it to more) and have a look, and then call support. I think it's likely a hardware failure.
Kevin. -----Original Message----- From: ADSM: Dist Stor Manager [mailto:[EMAIL PROTECTED]]On Behalf Of Paul van Dongen Sent: December 5, 2001 11:10 AM To: [EMAIL PROTECTED] Subject: Tsm and TL891DLX in SAN Hi all, We have the following SAN environment : Server Compaq running Windows 2000 SP2 HBA LP8000 Compaq SAN Swhitches and Router Library: 2 TL891DLX + Expansion Unit + Data Unit -> configured as one unit with 4 dlt drives and 52 tape slots. TSM 4.2.1 (IP22393) When we try any op read,write,audit lib,label,etc we get this Tsm event : 11/30/2001 8:19:24 AM ADSMServer Error (8300) 21 N/A LABCORREIO TSM Server Error: Server: LABCORREIO_SERVER1 ANR8300E I/O error on library TL891SAN (OP=8401C058, CC=205, KEY=FF, ASC=FF, ASCQ=FF,~SENSE=**NONE**,~Description=SCSI adapter failure). Refer to Appendix D in the 'Messages' manual for recommended action. 11/30/2001 8:17:32 AM ADSMServer Error (8300) 21 N/A LABCORREIO TSM Server Error: Server: LABCORREIO_SERVER1 ANR8300E I/O error on library TL891SAN (OP=8401C058, CC=205, KEY=FF, ASC=FF, ASCQ=FF,~SENSE=**NONE**,~Description=SCSI adapter failure). Refer to Appendix D in the 'Messages' manual for recommended action. 11/30/2001 8:15:41 AM ADSMServer Error (8300) 21 N/A LABCORREIO TSM Server Error: Server: LABCORREIO_SERVER1 ANR8300E I/O error on library TL891SAN (OP=8401C058, CC=205, KEY=FF, ASC=FF, ASCQ=FF,~SENSE=**NONE**,~Description=SCSI adapter failure). Refer to Appendix D in the 'Messages' manual for recommended action. 5/29/2001 9:13:09 AM ADSMServer Error (8300) 21 N/A LABCORREIO TSM Server Error: Server: LABCORREIO_SERVER1 ANR8300E I/O error on library TL891SAN (OP=8401C058, CC=205, KEY=FF, ASC=FF, ASCQ=FF,~SENSE=**NONE**,~Description=SCSI adapter failure). Refer to Appendix D in the 'Messages' manual for recommended action. Adsmscsi event : Dump Data: byte 0x2D=SRB Status, byte 0x2C=SCSI Status 11/30/2001 8:17:32 AM AdsmScsi Error None 1 N/A LABCORREIO A non check condition error has occured on device \Device\lb0.0.1.3 during Move Medium with completion code DD_SCSI_ADAPTER_FAILURE. Dump Data: byte 0x2D=SRB Status, byte 0x2C=SCSI Status 11/30/2001 8:15:41 AM AdsmScsi Error None 1 N/A LABCORREIO A non check condition error has occured on device \Device\lb0.0.1.3 during Move Medium with completion code DD_SCSI_ADAPTER_FAILURE. Dump Data: byte 0x2D=SRB Status, byte 0x2C=SCSI Status 5/29/2001 9:13:09 AM AdsmScsi Error None 1 N/A LABCORREIO A non check condition error has occured on device \Device\lb0.0.1.3 during Move Medium with completion code DD_SCSI_ADAPTER_FAILURE. Dump Data: byte 0x2D=SRB Status, byte 0x2C=SCSI Status 5/28/2001 6:10:11 PM AdsmScsi Error None 1 N/A LABCORREIO A non check condition error has occured on device \Device\lb0.0.1.3 during Move Medium with completion code DD_SCSI_ADAPTER_FAILURE. Dump Data: byte 0x2D=SRB Status, byte 0x2C=SCSI Status 5/28/2001 4:15:36 AM AdsmScsi Error None 1 N/A LABCORREIO A non check condition error has occured on device \Device\lb0.0.1.3 during Move Medium with completion code DD_SCSI_ADAPTER_FAILURE. Dump Data: byte 0x2D=SRB Status, byte 0x2C=SCSI Status 5/28/2001 4:10:44 AM AdsmScsi Error None 1 N/A LABCORREIO A non check condition error has occured on device \Device\lb0.0.1.3 during Move Medium with completion code DD_SCSI_ADAPTER_FAILURE. Compaq says that the HW is OK ! Does anyone know what is happening ? Any hint,similar environment working ? All help is welcome. I know about APAR IC31466 but its not clear about the problem (HW/Compaq or SW/Tivoli ?) and what are the solutions (patches,hw not supported,etc). Thanks in advance. Paul Gondim van Dongen Engenheiro de Sistemas VANguard - Value Added Network guardians http://www.vanguard-it.com.br Fone: 55 81 3225-0353 ------------------------------------------------------------------- Este e-mail foi enviado pelo site da Nlink: http://www.nlink.com.br
