Was there any problems doing a DEFINE LIBRARY?. I have a ESL9326DX tape library from Compaq.
Two things to try: Set the robot arm on its own SCSI connection. (By default the arm and drive0 and drive1 are on the same scsi connection.) or Try changing your robotic arm to scsi ID >2 on the library. I believe the default is ID 0, drive0 is ID1 and drive1 is ID2) I had to use option 1 adding a another scsi cable and terminating the robotic arm. Do you have a MDR (modular data router) between the SAN switch and the tape library? (if you are using fibre) Are you using TSM device drivers? Joe Cascanette The Cumis Group Limited -----Original Message----- From: Kevin Sawyer [mailto:[EMAIL PROTECTED]] Sent: Wednesday, December 05, 2001 12:46 PM To: [EMAIL PROTECTED] Subject: Re: Tsm and TL891DLX in SAN That's usually indicative of a hardware error. If you're in AIX run the errpt -a command (pipe it to more) and have a look, and then call support. I think it's likely a hardware failure. Kevin. -----Original Message----- From: ADSM: Dist Stor Manager [mailto:[EMAIL PROTECTED]]On Behalf Of Paul van Dongen Sent: December 5, 2001 11:10 AM To: [EMAIL PROTECTED] Subject: Tsm and TL891DLX in SAN Hi all, We have the following SAN environment : Server Compaq running Windows 2000 SP2 HBA LP8000 Compaq SAN Swhitches and Router Library: 2 TL891DLX + Expansion Unit + Data Unit -> configured as one unit with 4 dlt drives and 52 tape slots. TSM 4.2.1 (IP22393) When we try any op read,write,audit lib,label,etc we get this Tsm event : 11/30/2001 8:19:24 AM ADSMServer Error (8300) 21 N/A LABCORREIO TSM Server Error: Server: LABCORREIO_SERVER1 ANR8300E I/O error on library TL891SAN (OP=8401C058, CC=205, KEY=FF, ASC=FF, ASCQ=FF,~SENSE=**NONE**,~Description=SCSI adapter failure). Refer to Appendix D in the 'Messages' manual for recommended action. 11/30/2001 8:17:32 AM ADSMServer Error (8300) 21 N/A LABCORREIO TSM Server Error: Server: LABCORREIO_SERVER1 ANR8300E I/O error on library TL891SAN (OP=8401C058, CC=205, KEY=FF, ASC=FF, ASCQ=FF,~SENSE=**NONE**,~Description=SCSI adapter failure). Refer to Appendix D in the 'Messages' manual for recommended action. 11/30/2001 8:15:41 AM ADSMServer Error (8300) 21 N/A LABCORREIO TSM Server Error: Server: LABCORREIO_SERVER1 ANR8300E I/O error on library TL891SAN (OP=8401C058, CC=205, KEY=FF, ASC=FF, ASCQ=FF,~SENSE=**NONE**,~Description=SCSI adapter failure). Refer to Appendix D in the 'Messages' manual for recommended action. 5/29/2001 9:13:09 AM ADSMServer Error (8300) 21 N/A LABCORREIO TSM Server Error: Server: LABCORREIO_SERVER1 ANR8300E I/O error on library TL891SAN (OP=8401C058, CC=205, KEY=FF, ASC=FF, ASCQ=FF,~SENSE=**NONE**,~Description=SCSI adapter failure). Refer to Appendix D in the 'Messages' manual for recommended action. Adsmscsi event : Dump Data: byte 0x2D=SRB Status, byte 0x2C=SCSI Status 11/30/2001 8:17:32 AM AdsmScsi Error None 1 N/A LABCORREIO A non check condition error has occured on device \Device\lb0.0.1.3 during Move Medium with completion code DD_SCSI_ADAPTER_FAILURE. Dump Data: byte 0x2D=SRB Status, byte 0x2C=SCSI Status 11/30/2001 8:15:41 AM AdsmScsi Error None 1 N/A LABCORREIO A non check condition error has occured on device \Device\lb0.0.1.3 during Move Medium with completion code DD_SCSI_ADAPTER_FAILURE. Dump Data: byte 0x2D=SRB Status, byte 0x2C=SCSI Status 5/29/2001 9:13:09 AM AdsmScsi Error None 1 N/A LABCORREIO A non check condition error has occured on device \Device\lb0.0.1.3 during Move Medium with completion code DD_SCSI_ADAPTER_FAILURE. Dump Data: byte 0x2D=SRB Status, byte 0x2C=SCSI Status 5/28/2001 6:10:11 PM AdsmScsi Error None 1 N/A LABCORREIO A non check condition error has occured on device \Device\lb0.0.1.3 during Move Medium with completion code DD_SCSI_ADAPTER_FAILURE. Dump Data: byte 0x2D=SRB Status, byte 0x2C=SCSI Status 5/28/2001 4:15:36 AM AdsmScsi Error None 1 N/A LABCORREIO A non check condition error has occured on device \Device\lb0.0.1.3 during Move Medium with completion code DD_SCSI_ADAPTER_FAILURE. Dump Data: byte 0x2D=SRB Status, byte 0x2C=SCSI Status 5/28/2001 4:10:44 AM AdsmScsi Error None 1 N/A LABCORREIO A non check condition error has occured on device \Device\lb0.0.1.3 during Move Medium with completion code DD_SCSI_ADAPTER_FAILURE. Compaq says that the HW is OK ! Does anyone know what is happening ? Any hint,similar environment working ? All help is welcome. I know about APAR IC31466 but its not clear about the problem (HW/Compaq or SW/Tivoli ?) and what are the solutions (patches,hw not supported,etc). Thanks in advance. Paul Gondim van Dongen Engenheiro de Sistemas VANguard - Value Added Network guardians http://www.vanguard-it.com.br Fone: 55 81 3225-0353 ------------------------------------------------------------------- Este e-mail foi enviado pelo site da Nlink: http://www.nlink.com.br
