If it's Ubnt it's probably a dead radio. Probably 1/100000 chance the
cable shorted.
Josh Luthman
Office: 937-552-2340
Direct: 937-552-2343
1100 Wayne St
Suite 1337
Troy, OH 45373
On Mon, Nov 24, 2014 at 3:07 PM, Mathew Howard via Af <[email protected]
<mailto:[email protected]>> wrote:
Yep, could either be a dead AP or a shorted cable... I don't think
there's any way to tell from the ground.
It is a lot harder to make that decision when someone else is
doing the climbing... I wouldn't ask anyone to go up in weather I
wouldn't climb in myself, but then again, I've also climbed in
weather I wouldn't tell someone else to go up in. I don't think
there really is a good rule of thumb, a lot depends on what the
climber is comfortable with, and experience.
------------------------------------------------------------------------
*From:* Af [[email protected] <mailto:[email protected]>] on
behalf of Josh Luthman via Af [[email protected] <mailto:[email protected]>]
*Sent:* Monday, November 24, 2014 12:08 PM
*To:* [email protected] <mailto:[email protected]>
*Subject:* Re: [AFMUG] wind speed cut off for climbing
The radio is pulling too much current. Probably it is an
overload/short. It will fade out and then come on full
brightness. This was the green LED and may not exist with the LED
anymore, especially since it's a different type of LED.
Josh Luthman
Office: 937-552-2340 <tel:937-552-2340>
Direct: 937-552-2343 <tel:937-552-2343>
1100 Wayne St
Suite 1337
Troy, OH 45373
On Mon, Nov 24, 2014 at 12:02 PM, Ken Hohhof via Af <[email protected]
<mailto:[email protected]>> wrote:
I’ve never seen a flashing UBNT power supply, what does that
mean? Overload/short?
*From:* That One Guy via Af <mailto:[email protected]>
*Sent:* Monday, November 24, 2014 10:55 AM
*To:* [email protected] <mailto:[email protected]>
*Subject:* Re: [AFMUG] wind speed cut off for climbing
its only 100 feet, but its a shitty tower to climb, all
angled, one of those tripod ones that suck when theyre wet.
Ive slipped on this tower
new as in this would be his first unattended climb since training
im assuming its just a bad radio (flashing ubnt power supply,
but could be a failed cable) on an omni
On Mon, Nov 24, 2014 at 10:45 AM, Ken Hohhof via Af
<[email protected] <mailto:[email protected]>> wrote:
I would worry more about gusts than steady wind,
especially for rope work or complex positioning. Might
need additional ground crew and taglines, maybe a second
climber.
When you say new climber, how new? What kind of
training/certification? Ultimately you are depending on
the climber to call it off if it’s not safe, and a newbie
might not have the experience to know when it’s not safe.
If you’re talking about today, at least it’s been way
above freezing the past 2 days, so the likelihood of rain
freezing to the tower should be minimized.
Also, how high are you sending him? Big difference between
100 and 300 feet.
*From:* That One Guy via Af <mailto:[email protected]>
*Sent:* Monday, November 24, 2014 10:36 AM
*To:* [email protected] <mailto:[email protected]>
*Subject:* Re: [AFMUG] wind speed cut off for climbing
fun wintery rain sleet snow mix, new climber 38mph wind
gusts, ap outage
On Mon, Nov 24, 2014 at 10:34 AM, Brian Sullivan via Af
<[email protected] <mailto:[email protected]>> wrote:
Depends what i'm climbing for. Repair or upgrade?
Is there rain/sleet/snow mixed with the wind?
On 11/24/2014 10:31 AM, That One Guy via Af wrote:
whats everybodys rule of thumb for cutting off climbing
--
All parts should go together without forcing. You
must remember that the parts you are reassembling
were disassembled by you. Therefore, if you can't get
them together again, there must be a reason. By all
means, do not use a hammer. -- IBM maintenance
manual, 1925
--
All parts should go together without forcing. You must
remember that the parts you are reassembling were
disassembled by you. Therefore, if you can't get them
together again, there must be a reason. By all means, do
not use a hammer. -- IBM maintenance manual, 1925
--
All parts should go together without forcing. You must
remember that the parts you are reassembling were disassembled
by you. Therefore, if you can't get them together again, there
must be a reason. By all means, do not use a hammer. -- IBM
maintenance manual, 1925
