If it's Ubnt it's probably a dead radio. Probably 1/100000 chance the cable shorted.
Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Mon, Nov 24, 2014 at 3:07 PM, Mathew Howard via Af <[email protected]> wrote: > Yep, could either be a dead AP or a shorted cable... I don't think > there's any way to tell from the ground. > > It is a lot harder to make that decision when someone else is doing the > climbing... I wouldn't ask anyone to go up in weather I wouldn't climb in > myself, but then again, I've also climbed in weather I wouldn't tell > someone else to go up in. I don't think there really is a good rule of > thumb, a lot depends on what the climber is comfortable with, and > experience. > > ------------------------------ > *From:* Af [[email protected]] on behalf of Josh Luthman via Af [ > [email protected]] > *Sent:* Monday, November 24, 2014 12:08 PM > *To:* [email protected] > *Subject:* Re: [AFMUG] wind speed cut off for climbing > > The radio is pulling too much current. Probably it is an > overload/short. It will fade out and then come on full brightness. This > was the green LED and may not exist with the LED anymore, especially since > it's a different type of LED. > > > Josh Luthman > Office: 937-552-2340 > Direct: 937-552-2343 > 1100 Wayne St > Suite 1337 > Troy, OH 45373 > > On Mon, Nov 24, 2014 at 12:02 PM, Ken Hohhof via Af <[email protected]> wrote: > >> I’ve never seen a flashing UBNT power supply, what does that mean? >> Overload/short? >> >> >> *From:* That One Guy via Af <[email protected]> >> *Sent:* Monday, November 24, 2014 10:55 AM >> *To:* [email protected] >> *Subject:* Re: [AFMUG] wind speed cut off for climbing >> >> its only 100 feet, but its a shitty tower to climb, all angled, one of >> those tripod ones that suck when theyre wet. Ive slipped on this tower >> new as in this would be his first unattended climb since training >> im assuming its just a bad radio (flashing ubnt power supply, but could >> be a failed cable) on an omni >> >> >> >> On Mon, Nov 24, 2014 at 10:45 AM, Ken Hohhof via Af <[email protected]> wrote: >> >>> I would worry more about gusts than steady wind, especially for rope >>> work or complex positioning. Might need additional ground crew and >>> taglines, maybe a second climber. >>> >>> When you say new climber, how new? What kind of >>> training/certification? Ultimately you are depending on the climber to >>> call it off if it’s not safe, and a newbie might not have the experience to >>> know when it’s not safe. If you’re talking about today, at least it’s been >>> way above freezing the past 2 days, so the likelihood of rain freezing to >>> the tower should be minimized. >>> >>> Also, how high are you sending him? Big difference between 100 and 300 >>> feet. >>> >>> >>> *From:* That One Guy via Af <[email protected]> >>> *Sent:* Monday, November 24, 2014 10:36 AM >>> *To:* [email protected] >>> *Subject:* Re: [AFMUG] wind speed cut off for climbing >>> >>> fun wintery rain sleet snow mix, new climber 38mph wind gusts, ap >>> outage >>> >>> On Mon, Nov 24, 2014 at 10:34 AM, Brian Sullivan via Af <[email protected]> >>> wrote: >>> >>>> Depends what i'm climbing for. Repair or upgrade? >>>> Is there rain/sleet/snow mixed with the wind? >>>> >>>> >>>> On 11/24/2014 10:31 AM, That One Guy via Af wrote: >>>> >>>> whats everybodys rule of thumb for cutting off climbing >>>> >>>> -- >>>> All parts should go together without forcing. You must remember that >>>> the parts you are reassembling were disassembled by you. Therefore, if you >>>> can't get them together again, there must be a reason. By all means, do not >>>> use a hammer. -- IBM maintenance manual, 1925 >>>> >>>> >>>> >>> >>> >>> -- >>> All parts should go together without forcing. You must remember that >>> the parts you are reassembling were disassembled by you. Therefore, if you >>> can't get them together again, there must be a reason. By all means, do not >>> use a hammer. -- IBM maintenance manual, 1925 >>> >> >> >> >> -- >> All parts should go together without forcing. You must remember that >> the parts you are reassembling were disassembled by you. Therefore, if you >> can't get them together again, there must be a reason. By all means, do not >> use a hammer. -- IBM maintenance manual, 1925 >> > >
