Using: http://store.packetflux.com/gigabit-syncinjector-for-24-volt-cambium-radios/
Reproduced this at two tower sites with PMP450i AP's set at 1000base. Current Site: Dlink Managed Vlan Gigabit Switch Gigabit SyncInjector powered at 48 volts. APC surge arrestor. Tried both 430APC-HV and GigE-APC-HV. Both worked but only at 100base. 200 foot shielded cat-5 450i AP. Victory of sorts. At this site I removed the APC surge arrestor completely and replaced with cheap plastic coupling. I now have 1000base connection at the 450i. On Thu, Oct 29, 2015 at 2:21 PM, Forrest Christian (List Account) <[email protected]> wrote: > Which injector are you using? > > On Oct 29, 2015 11:05 AM, "Matt" <[email protected]> wrote: >> >> I have mine set on 1000base and it will only do 100base. It tries to do >> 1000base at first, you can see the dlink managed switch light blink green at >> first, then it gives up and goes too 100base. It passes through 200 foot of >> shielded cat-5 then a GigE-APC-HV. I have also tried a 430APC-HV with same >> result. >> >> >> On Thu, Oct 29, 2015 at 11:28 AM, Josh Luthman >> <[email protected]> wrote: >>> >>> Not a stupid question, George. That was it. >>> >>> Factory default is actually the second to last option - auto 100/10/f/h. >>> I mean config from the factory - not what happens if you push factory >>> default in software. I did take this radio from 14.0 (factory) to 14.1b6. >>> >>> >>> Josh Luthman >>> Office: 937-552-2340 >>> Direct: 937-552-2343 >>> 1100 Wayne St >>> Suite 1337 >>> Troy, OH 45373 >>> >>> On Thu, Oct 29, 2015 at 7:20 AM, Forrest Christian (List Account) >>> <[email protected]> wrote: >>>> >>>> Good catch... My testing 450i seems to default to gigabit off (after a >>>> factory default). >>>> >>>> Once I set it on (which I seem to remember doing previously as well), it >>>> links right up at gigabit speeds. This is with a RB850Gx2 >>>> >>>> -forrest >>>> >>>> >>>> >>>> >>>> >>>> >>>> On Wed, Oct 28, 2015 at 5:32 PM, George Skorup <[email protected]> >>>> wrote: >>>>> >>>>> Stupid question.... Does the 450i have this like 13.x on the regular >>>>> 450? Default is auto 100f/100h/10f/10h. >>>>> >>>>> >>>>> > >>>>> On 10/28/2015 4:37 PM, Josh Luthman wrote: >>>>>> >>>>>> I wonder if this unit is capable of doing gigabit with 450i? It does >>>>>> gigabit on the ePMP. >>>>>> >>>>>> >>>>>> Josh Luthman >>>>>> Office: 937-552-2340 >>>>>> Direct: 937-552-2343 >>>>>> 1100 Wayne St >>>>>> Suite 1337 >>>>>> Troy, OH 45373 >>>>>> >>>>>> On Wed, Oct 28, 2015 at 5:36 PM, Matt <[email protected]> >>>>>> wrote: >>>>>>> >>>>>>> > I have a PacketFlux SyncInjector Gigabit that goes to the 450i. >>>>>>> > It's got a >>>>>>> > 48v power supply. There is no syncpipe, nor would anything work in >>>>>>> > the lab. >>>>>>> > The test PC has two Intel gigabit NICs. >>>>>>> > >>>>>>> > My issue is that I can only get a 100 Mbit here. >>>>>>> > >>>>>>> > I have it set to generate sync right now and I can access it just >>>>>>> > fine. If >>>>>>> > I have it set for autosync + free run I get some problems accessing >>>>>>> > the >>>>>>> > device (ping works for a few seconds on, then off, web interface is >>>>>>> > not >>>>>>> > responsive at all, CNUT flat out doesn't work). The ethernet link >>>>>>> > does not >>>>>>> > go down/up with sync at all. >>>>>>> > >>>>>>> > Any other clues or things to look at? >>>>>>> >>>>>>> FYI, I am seeing same thing. It passes through a GigE-APC-HV on way >>>>>>> to 450i AP. AP is getting sync from daisy chained syncpipe source >>>>>>> hooked too Gigabit SyncInjector powered by 48 volt. AP is working >>>>>>> fine just at 100mbps ethernet. >>>>>> >>>>>> >>>>> >>>> >>>> >>>> >>>> -- >>>> Forrest Christian CEO, PacketFlux Technologies, Inc. >>>> Tel: 406-449-3345 | Address: 3577 Countryside Road, Helena, MT 59602 >>>> [email protected] | http://www.packetflux.com >>>> >>>> >>> >>
