I meant for the admin side? Regards, Chuck
On Fri, Dec 4, 2015 at 4:27 PM, Faisal Imtiaz <[email protected]> wrote: > Just guessing.... > > Drop down on top right, select signup/create account ! > > :) > > Faisal Imtiaz > Snappy Internet & Telecom > 7266 SW 48 Street > Miami, FL 33155 > Tel: 305 663 5518 x 232 > > Help-desk: (305)663-5518 Option 2 or Email: [email protected] > > ------------------------------ > > *From: *"Chuck Hogg" <[email protected]> > *To: *[email protected] > *Sent: *Friday, December 4, 2015 4:25:07 PM > *Subject: *Re: [AFMUG] Need new billing solution asap!!! > > Anyone know how to login to his demo? > > Regards, > Chuck > > On Fri, Dec 4, 2015 at 11:28 AM, Simon Westlake <[email protected]> > wrote: > >> https://github.com/spencerlambert/wisp-central-control >> >> On 12/4/2015 10:08 AM, Jeremy wrote: >> >> Isn't Spencer Lambert's web front-end free? Last time I saw him at >> Animal Farm he was touting it and said he would help with setup and >> customization at a flat rate of $100/hr. He is located in Utah, also. If >> you want something cheap or free that may be an option. It would probably >> be worth contacting him. I recommend Powercode. >> >> On Fri, Dec 4, 2015 at 8:58 AM, Craig Schmaderer < >> [email protected]> wrote: >> >>> I've been looking at https://www.whmcs.com/ >>> I have a friend that uses it for his ventrillo voice business and it >>> does auto billing and ticketing and is cheap. I think you can get a hosted >>> solution if you don't want to install it. >>> >>> Craig schmaderer >>> Skywave Wireless, Inc. >>> >>> >>> >>> >>> On Fri, Dec 4, 2015 at 7:41 AM -0800, "Brett A Mansfield" < >>> [email protected]> wrote: >>> >>> Here is what I've always said about quality, cheap and fast. >>> >>> You can only pick two. You will never have all three. >>> >>> For this I need fast and quality. Cheap is relative in this case. I >>> don't have a lot of customers so the $200/mo min that visp requires is >>> about $100-150 too much for me. I'm fine with a reasonable one time fee, >>> but it must be reasonable. >>> >>> I used to use waveapps to just invoice and then customers could pay >>> using the invoice. But if they didn't get the email or lost it, they >>> couldn't pay their bill. >>> >>> I appreciate everyone's input on this. I think I'm going with platypus >>> and pay someone to set it up. >>> >>> I like powercode, I just cannot justify the initial cost for my small >>> size operation. >>> >>> Thank you, >>> Brett A Mansfield >>> >>> On Dec 4, 2015, at 7:47 AM, Chris Fabien < <[email protected]> >>> [email protected]> wrote: >>> >>> Good, cheap, and fast? You know what they say about that. >>> >>> We are reasonably happy with Powercode. Few gripes but it has never >>> double or triple charged our customers. >>> On Dec 4, 2015 1:35 AM, "Brett A Mansfield" < >>> <[email protected]>[email protected]> wrote: >>> >>>> I'm looking for a good billing solution that is cheap and I can have up >>>> in running immediately. >>>> >>>> I've had far too many issues with my current billing system. >>>> >>>> I need something turnkey and cheap. My WISP is a fairly small operation. >>>> >>>> I am not willing to pay per sub, especially if there is a minimum like >>>> visp. I don't want to buy any new hardware. I looked at platypus, but it >>>> cannot be deployed easily or quickly. I looked at powercode, but I don't >>>> want to buy any new hardware. >>>> >>>> Is there anything out there that might fit my needs? Or should I just >>>> go back to manual invoicing with quickbooks? >>>> >>>> Thank you, >>>> Brett A Mansfield >>>> >>> >> >> -- >> Simon Westlake >> Skype: Simon_Sonar >> Email: [email protected] >> Phone: (702) 447-1247 >> --------------------------- >> Sonar Software Inc >> The next generation of ISP billing and OSShttps://sonar.software >> >> >
