will try it and see what happens... ----- Original Message ----- From: Mathew Howard To: af Sent: Wednesday, January 20, 2016 11:24 PM Subject: Re: [AFMUG] weird ap-repeater setup issue with 5.6.3 firmware
If it is setup as a bridge, yes, most likely. I would enable it anyway, it doesn't hurt anything to have it on. On Wed, Jan 20, 2016 at 9:41 PM, CBB - Jay Fuller <[email protected]> wrote: ah - transparent bridge mode was NOT enabled on that client. do you think that is/was my problem? ----- Original Message ----- From: Mathew Howard To: af Sent: Wednesday, January 20, 2016 9:11 PM Subject: Re: [AFMUG] weird ap-repeater setup issue with 5.6.3 firmware Yeah, I'm curious how it's configured... is it in transparent bridge mode? On Wed, Jan 20, 2016 at 5:55 PM, CBB - Jay Fuller <[email protected]> wrote: Yes. What am I checking for? Transparent bridging? ----- Original Message ----- From: Mathew Howard To: af Sent: Wednesday, January 20, 2016 5:09 PM Subject: Re: [AFMUG] weird ap-repeater setup issue with 5.6.3 firmware Can you access the station now and see how it's configured? On Wed, Jan 20, 2016 at 3:10 PM, CBB - Jay Fuller <[email protected]> wrote: FYI, i had to go back to firmware 5.5.10 but that apparently resolved the problem. The station IP is showing up correctly now and we're checking with the customer to verify. ----- Original Message ----- From: CBB - Jay Fuller To: [email protected] Sent: Wednesday, January 20, 2016 2:01 PM Subject: Re: [AFMUG] weird ap-repeater setup issue with 5.6.3 firmware not yet. but i thought if i were to roll back firmware i could turn off one access point and turn on the other... ----- Original Message ----- From: Mathew Howard To: af Sent: Wednesday, January 20, 2016 1:35 PM Subject: Re: [AFMUG] weird ap-repeater setup issue with 5.6.3 firmware sounds to me like transparent bridging isn't working right on the client... there may be something different with how it's handled on the newer firmware. Did you try switching the AP to access point and enabling WDS/transparent bridge instead of using AP-Repeater? On Wed, Jan 20, 2016 at 1:20 PM, That One Guy /sarcasm <[email protected]> wrote: good luck over there man, its a minefield On Wed, Jan 20, 2016 at 1:07 PM, CBB - Jay Fuller <[email protected]> wrote: My next stop is ubnt forums or support This lady is not happy... Sent from my Verizon 4G LTE Smartphone ----- Reply message ----- From: "Josh Luthman" <[email protected]> To: "[email protected]" <[email protected]> Subject: [AFMUG] weird ap-repeater setup issue with 5.6.3 firmware Date: Wed, Jan 20, 2016 12:34 PM IP Alias just creates a 169.254.x.y where x.y is based on the MAC address. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Wed, Jan 20, 2016 at 1:33 PM, That One Guy /sarcasm <[email protected]> wrote: is that auto ip ilias thing causing this, if the cdp and other tickbox are deselected you shouldnt be seeing any ips i dont thing On Wed, Jan 20, 2016 at 11:42 AM, CBB - Jay Fuller <[email protected]> wrote: here is the station list. again, the file we have show her radio as 10.8.19.56 ; not 106. We show she has a router at 106 ----- Original Message ----- From: CBB - Jay Fuller To: Ubiquiti Users Group ; [email protected] ; [email protected] Sent: Wednesday, January 20, 2016 11:40 AM Subject: weird ap-repeater setup issue with 5.6.3 firmware as many of you know, we've been going to 5.6.3 today we got a call from a customer who reported she is down. investigating, we discovered she is on a 900 mhz ubnt access point setup as an ap-repeater. This problem started after the firmware upgrade so we are assuming it's firmware related or perhaps something is treated differently in 5.6.3 (for example, we also had to update all of our oid's for graphing purposes) :) suggestions? we noticed no "transparent bridge" mode on an ap repeater, and we also noticed the station is showing connected, but it is showing the IP address of the customer's bridged router ; NOT the ip address of the radio. I have also tried checking the "auto" box briefly ; it did not change access to the radio. I can not access the radio although it shows connected. -- If you only see yourself as part of the team but you don't see your team as part of yourself you have already failed as part of the team. -- If you only see yourself as part of the team but you don't see your team as part of yourself you have already failed as part of the team.
