Are you seriously still running 11.2 or 12.1? What version is the AP on?
There was a timing bug for a very long time that was fixed with the
final 13.4.1 release. There *is* a difference between power port and
timing port sync prior to 13.4.1.
The difference between a reg and a re-reg is very simple. A reg is when
the session is new or idle. A re-reg means the AP hasn't torn down that
session, but sees a registration attempt. That's often the case when the
VC isn't very active, so the AP just kinda assumes it's still there. Or
the SM doesn't see enough beacons and assumes it's out of session.
Bursty interference, multi-path, etc.
Also, what h/w is the AP? P9's didn't have the best RF performance and
calibration could be an issue. Been through that a dozen times. As we
pull down 900 APs, any P9's get compared to a known-good P9 and a P10 AP
using 60dB pad. If the uplink and downlink power and jitter levels
aren't sane, they go right in the recycle bin.
On 11/10/2017 11:05 AM, Jay Weekley wrote:
What do you think the problem here is? We had to replace a PMP 100
900 MHz access point earlier in the week and now the Session and Reg
counts seem very high but there are no (zero) Re-Regs on any of the
clients. I could blame it on interference or timing but the zero
Re-Regs confuses me. The AP uptime when I took this information was
26 hours and we're using Packeflux timing. We are also using a new
Sync Injector but a used Sync Pipe.
LUID: 002 - [0a-00-3e-93-07-8c] State: IN SESSION (Encrypt Disabled)
Site Name: , Darlene
Software Version: CANOPY 12.1
FPGA Version: 111010 (DES, Sched, US/ETSI) P10
Session Timeout: 0, AirDelay: 70200 ns, 234 bits (approximately
6.534 miles (34503 feet))
Session Count: 295, Reg Count: 295, Re-Reg Count: 0, Session Uptime:
02:41:03
LUID: 003 - [0a-00-3e-93-61-03] State: IN SESSION (Encrypt Disabled)
Site Name: , Scottie
Software Version: CANOPY 12.1
FPGA Version: 111010 (DES, Sched, US/ETSI) P10
Session Timeout: 0, AirDelay: 3300 ns, 11 bits (approximately
0.307 miles (1621 feet))
Session Count: 43, Reg Count: 43, Re-Reg Count: 0, Session Uptime:
03:19:04
Jitter (Avg/Last): 8/9 Power Level (Avg/Last): -56/-56
Rate: VC 19 Rate 2X/2X
LUID: 004 - [0a-00-3e-92-47-84] State: IN SESSION (Encrypt Disabled)
Site Name: , Jeff
Software Version: CANOPY 12.1
FPGA Version: 101410 (DES, Sched, US/ETSI) P9
Session Timeout: 0, AirDelay: 28500 ns, 95 bits (approximately
2.652 miles (14007 feet))
Session Count: 252, Reg Count: 252, Re-Reg Count: 0, Session Uptime:
02:45:22
LUID: 005 - [0a-00-3e-91-9f-9b] State: IN SESSION (Encrypt Disabled)
Site Name: , Joseph
Software Version: CANOPY 12.1
FPGA Version: 101410 (DES, Sched, US/ETSI) P9
Session Timeout: 0, AirDelay: 9300 ns, 31 bits (approximately
0.865 miles (4570 feet))
Session Count: 41, Reg Count: 41, Re-Reg Count: 0, Session Uptime:
03:18:41
LUID: 006 - [0a-00-3e-93-08-16] State: IN SESSION (Encrypt Disabled)
Site Name: , Steve
Software Version: CANOPY 12.1
FPGA Version: 111010 (DES, Sched, US/ETSI) P10
Session Timeout: 0, AirDelay: 20100 ns, 67 bits (approximately
1.871 miles (9879 feet))
Session Count: 328, Reg Count: 328, Re-Reg Count: 0, Session Uptime:
02:43:56
LUID: 007 - [0a-00-3e-93-61-8d] State: IN SESSION (Encrypt Disabled)
Site Name: , Ben
Software Version: CANOPY 11.2
FPGA Version: 111010 (DES, Sched, US/ETSI) P10
Session Timeout: 0, AirDelay: 81900 ns, 273 bits (approximately
7.623 miles (40253 feet))
Session Count: 382, Reg Count: 382, Re-Reg Count: 0, Session Uptime:
02:37:09
LUID: 008 - [0a-00-3e-94-e5-39] State: IN SESSION (Encrypt Disabled)
Site Name: , Regina
Software Version: CANOPY 12.1
FPGA Version: 111010 (DES, Sched, US/ETSI) P10
Session Timeout: 0, AirDelay: 17100 ns, 57 bits (approximately
1.591 miles (8404 feet))
Session Count: 35, Reg Count: 35, Re-Reg Count: 0, Session Uptime:
03:18:38
