Hi, Just a bit more info. By rebooting and doing a couple of power cycles on the external A/D/D/A I have been able to get the RME to acknowledge that it's seeing an ADAT sync at 44.1K, so I think at least the clock is being sent.
This specific external unit (AI-3 for now) supports a loopback, where the ADAT in can be looped and sent back on its ADAT out. In doing this, I cannot see the audio signal I send it, implying that it is actually not receiving one. Also, I sent the wave file recorded using jackrec to my Windows box. (A copy of a Yellowjackets tune) It plays fine, so it appears that jack and alsaplayer are working OK. Thanks in advance again. Cheers, Mark On Sat, 2003-04-12 at 10:37, Mark Knecht wrote: > [EMAIL PROTECTED] card0]# more /proc/asound/card0/hdsp > RME HDSP 9652 (Card #1) > Buffers: capture dde00000 playback ddc00000 > IRQ: 10 Registers bus: 0xe8800000 VM: 0xe0967000 > Control register: 0x1008098 > Status register: 0x6086a48 > Status2 register: 0xffff8061 > FIFO status: 0 > MIDI1 Output status: 0xffffff00 > MIDI1 Input status: 0xffffff80 > MIDI2 Output status: 0xffffff00 > MIDI2 Input status: 0xffffff5f > > Buffer Size (Latency): 1024 samples (2 periods of 4096 bytes) > Hardware pointer (frames): 1024 > Passthru: no > Line out: on > Firmware version: 1 > > Sample Clock Source: Internal 44.1 kHz > Preferred Sync Reference: ADAT1 > AutoSync Reference: ADAT1 > AutoSync Frequency: 48000 > System Clock Mode: Master > System Clock Frequency: 44100 > > IEC958 input: Internal > IEC958 output: Coaxial only > IEC958 quality: Consumer > IEC958 emphasis: off > IEC958 NonAudio: off > IEC958 sample rate: Error flag set > > ADAT1: Lock > ADAT2: No Lock > ADAT3: No Lock > SPDIF: No Lock > Word Clock: No Lock > ADAT Sync: No Lock > > [EMAIL PROTECTED] card0]# > [EMAIL PROTECTED] mark]$ cat /proc/asound/card0/hdsp RME HDSP 9652 (Card #1) Buffers: capture de600000 playback de400000 IRQ: 10 Registers bus: 0xe8800000 VM: 0xe0967000 Control register: 0x1008090 Status register: 0x2040008 Status2 register: 0xffff8041 FIFO status: 0 MIDI1 Output status: 0xffffff00 MIDI1 Input status: 0xffffff3d MIDI2 Output status: 0xffffff00 MIDI2 Input status: 0xffffff39 Buffer Size (Latency): 64 samples (2 periods of 256 bytes) Hardware pointer (frames): 0 Passthru: no Line out: on Firmware version: 1 Sample Clock Source: Internal 44.1 kHz Preferred Sync Reference: ADAT1 AutoSync Reference: ADAT1 AutoSync Frequency: 44100 System Clock Mode: Master System Clock Frequency: 44100 IEC958 input: Internal IEC958 output: Coaxial only IEC958 quality: Consumer IEC958 emphasis: off IEC958 NonAudio: off IEC958 sample rate: Error flag set ADAT1: Sync ADAT2: No Lock ADAT3: No Lock SPDIF: No Lock Word Clock: No Lock ADAT Sync: No Lock [EMAIL PROTECTED] mark]$ ------------------------------------------------------- This SF.net email is sponsored by: Etnus, makers of TotalView, The debugger for complex code. Debugging C/C++ programs can leave you feeling lost and disoriented. TotalView can help you find your way. Available on major UNIX and Linux platforms. Try it free. www.etnus.com _______________________________________________ Alsa-devel mailing list [EMAIL PROTECTED] https://lists.sourceforge.net/lists/listinfo/alsa-devel
