can you share the complete terminal log?? dont you see complete bootlog like below??
## Booting image at 80300000 ... Image Name: Linux-2.6.32-00004-g494747b Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2298904 Bytes = 2.2 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux........................................................................................................................................................... done, booting the kernel. ÿLinux version 2.6.3 ..<trace continues> On Mon, Apr 12, 2010 at 1:29 PM, ajish zacharias <[email protected]> wrote: > > sir thanks for advice, > i try boot command ,then terminal it is mention booting linux > kernel ,but hdmi sreen doesn't get any o/p , in terminal also same > message(booting from linux kernel ) ,sir can you tell what is the > problem ,thanking in advance > with regard ajish zacharias > On Apr 9, 1:43 pm, Deva R <[email protected]> wrote: >> can see what happens when you 'boot', instead of a saveenv&reset? >> btw - u missed 'saveenv', so even if u reset, uboot got nothing to boot. >> >> and 2 hours is way long., reset happens in couple of seconds.. if not >> there's some problem. >> a power cycle should have completed after 'reset' command., >> >> On Fri, Apr 9, 2010 at 10:14 AM, ajish zacharias >> >> <[email protected]> wrote: >> > Sir , >> > I tried procedure mentioned in >> > http://code.google.com/p/rowboat/wiki/ConfigureAndBuild. >> > Then i got terminal window shown in below.In that procedure i didn't >> > use saveenv command In my previous attempt i use it,the result was >> > same.I got message resetting ,i wait for almost 2 hour but there is >> > nochange in terminal. >> >> > OMAP3530-GP ES3.0, CPU-OPP2 L3-165MHz >> >> > OMAP3Beagleboard+ LPDDR/NAND >> >> > DRAM: 128 MB >> >> > NAND: 256 MiB >> >> > In: serial >> >> > Out: serial >> >> > Err: serial >> >> >Boardrevision Ax/Bx >> >> > Die ID #5ac400030000000004013f8901001001 >> >> > Hit any key to stop autoboot: 0 >> >> > OMAP3 beagleboard.org # >> >> > OMAP3 beagleboard.org # mmc init >> >> > mmc1 is available >> >> > OMAP3 beagleboard.org # >> >> > mmc1 is available >> >> > OMAP3 beagleboard.org # setenv bootcmd 'mmc init;fatload mmc 1 >> > 80200000 uImage; bootm 80200000' >> >> > OMAP3 beagleboard.org # >> >> > Unknown command '' - try 'help' >> >> > OMAP3 beagleboard.org # setenv bootargs 'mem=128M >> > androidboot.console=ttyS2 console=tty0 console=ttyS2,115200n8 root=/ >> > dev/mmcblk0p1 rw init=/init rootwait >> > omapfb.viedo_mode=640x480mr...@60' >> >> > OMAP3 beagleboard.org # reset >> >> > resetting ... >> >> > thanking advance >> >> > with regards Ajish Zacharias(CAIR,DRDO) >> >> > -- >> > unsubscribe:[email protected] >> > website:http://groups.google.com/group/android-porting >> >> > To unsubscribe, reply using "remove me" as the subject. > > -- > unsubscribe: [email protected] > website: http://groups.google.com/group/android-porting > -- unsubscribe: [email protected] website: http://groups.google.com/group/android-porting
