Check this from the logs: init: cannot find '/system/bin/mountd', disabling 'mountd'
It's not able to mount the USB device, as mount daemon is not found/ disabled - On Sep 14, 6:44 pm, PREMRAJ SV <[email protected]> wrote: > Hello all, > I was trying to connect gsm modem to Android. Using USB Hub for > connecting gsm modem via serail to usb convertor. I have enabled kernel > configuration for usb gsm modem support. While booting the filesystem is > loaded and after sometime it gets remounted saying that there is filesystem > error in entry.. I have already posted similar post for ttyUSB) not > detected. Trying again once got this error. My log from cutecom are, > -------------------------------------------------------------------------------------------------------------------------- > > Starting kernel ... > > Linux version 2.6.32-rc6 (r...@prem-laptop) (gcc version 4.3.2 (Sourcery G++ > Lite 2008q3-72) ) #20 PREEMPT Tue Sep 14 18:03:51 IST 2010 > CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 > CPU: VIVT data cache, VIVT instruction cache > Machine: OMAPL 138 Hawkboard.org > Memory policy: ECC disabled, Data cache writeback > DaVinci da850/omap-l138 variant 0x0 > Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 > Kernel command line: console=ttyS2,115200n8 noinitrd root=/dev/sda1 > video=omapfb.mode=dvi:1280*1280...@60 androidboot.console=ttyS2 rootwait rw > init=/init > Unknown boot option `androidboot.console=ttyS2': ignoring > PID hash table entries: 512 (order: -1, 2048 bytes) > Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) > Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) > Memory: 128MB = 128MB total > Memory: 124344KB available (4460K code, 816K data, 148K init, 0K highmem) > SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 > Hierarchical RCU implementation. > NR_IRQS:245 > Console: colour dummy device 80x30 > Calibrating delay loop... 149.50 BogoMIPS (lpj=747520) > Mount-cache hash table entries: 512 > CPU: Testing write buffer coherency: ok > DaVinci: 144 gpio irqs > regulator: core version 0.5 > NET: Registered protocol family 16 > bio: create slab <bio-0> at 0 > SCSI subsystem initialized > usbcore: registered new interface driver usbfs > usbcore: registered new interface driver hub > usbcore: registered new device driver usb > Switching to clocksource timer0_1 > musb_hdrc: version 6.0, cppi4.1-dma, (host+peripheral), debug=0 > Waiting for USB PHY clock good... > musb_hdrc: USB OTG mode controller at fee00000 using DMA, IRQ 58 > musb_hdrc musb_hdrc: MUSB HDRC host driver > musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1 > usb usb1: configuration #1 chosen from 1 choice > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 1 port detected > NET: Registered protocol family 2 > IP route cache hash table entries: 1024 (order: 0, 4096 bytes) > TCP established hash table entries: 4096 (order: 3, 32768 bytes) > TCP bind hash table entries: 4096 (order: 2, 16384 bytes) > TCP: Hash tables configured (established 4096 bind 4096) > TCP reno registered > NET: Registered protocol family 1 > RPC: Registered udp transport module. > RPC: Registered tcp transport module. > RPC: Registered tcp NFSv4.1 backchannel transport module. > ashmem: initialized > Installing knfsd (copyright (C) 1996 [email protected]). > JFFS2 version 2.2. (NAND) \0xc2\0xa9 2001-2006 Red Hat, Inc. > msgmni has been set to 243 > alg: No test for stdrng (krng) > io scheduler noop registered > io scheduler anticipatory registered (default) > da8xx_lcdc da8xx_lcdc.0: GLCD: Found VGA_Monitor panel > Console: switching to colour frame buffer device 80x30 > Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled > serial8250.0: ttyS0 at MMIO 0x1c42000 (irq = 25) is a 16550A > serial8250.0: ttyS1 at MMIO 0x1d0c000 (irq = 53) is a 16550A > serial8250.0: ttyS2 at MMIO 0x1d0d000 (irq = 61) is a 16550A > console [ttyS2] enabled > brd: module loaded > loop: module loaded > Uniform Multi-Platform E-IDE driver > ide-gd driver 1.18 > PPP generic driver version 2.4.2 > PPP Deflate Compression module registered > PPP BSD Compression module registered > PPP MPPE Compression module registered > NET: Registered protocol family 24 > PPPoL2TP kernel driver, V1.0 > SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256). > Equalizer2002: Simon Janes ([email protected]) and David S. Miller ( > [email protected]) > tun: Universal TUN/TAP device driver, 1.6 > tun: (C) 1999-2004 Max Krasnyansky <[email protected]> > console [netcon0] enabled > netconsole: network logging started > ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver > ohci ohci.0: DA8xx OHCI > ohci ohci.0: new USB bus registered, assigned bus number 2 > ohci ohci.0: irq 59, io mem 0x01e25000 > usb usb2: configuration #1 chosen from 1 choice > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 1 port detected > usbcore: registered new interface driver cdc_acm > cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN > adapters > Initializing USB Mass Storage driver... > usbcore: registered new interface driver usb-storage > USB Mass Storage support registered. > usbcore: registered new interface driver usbserial > usbserial: USB Serial Driver core > USB Serial support registered for GSM modem (1-port) > usbcore: registered new interface driver option > option: v0.7.2:USB Driver for GSM modems > g_ether gadget: using random self ethernet address > g_ether gadget: using random host ethernet address > usb0: MAC ee:3a:5d:cf:a3:bd > usb0: HOST MAC 0e:34:ca:a2:00:a8 > g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 > g_ether gadget: g_ether ready > mice: PS/2 mouse device common for all mice > i2c /dev entries driver > Linux telephony interface: v1.00 > ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/none/none/1.1.2.2 > Modular ISDN core version 1.1.21 > NET: Registered protocol family 34 > usbcore: registered new interface driver usbhid > usbhid: v2.6:USB HID core driver > logger: created 64K log 'log_main' > logger: created 256K log 'log_events' > logger: created 64K log 'log_radio' > logger: created 64K log 'log_system' > Advanced Linux Sound Architecture Driver Version 1.0.21. > ALSA device list: > No soundcards found. > TCP cubic registered > NET: Registered protocol family 17 > Bridge firewalling registered > Ebtables v2.0 registered > davinci_emac_probe: using random MAC addr: 2a:08:de:ec:93:54 > emac-mii: probed > Waiting for root device /dev/sda1... > usb 2-1: new full speed USB device using ohci and address 2 > usb 2-1: configuration #1 chosen from 1 choice > hub 2-1:1.0: USB hub found > hub 2-1:1.0: 4 ports detected > usb 2-1.2: new full speed USB device using ohci and address 3 > usb 2-1.2: not running at top speed; connect to a high speed hub > usb 2-1.2: configuration #1 chosen from 1 choice > scsi0 : SCSI emulation for USB Mass Storage devices > usb 2-1.4: new full speed USB device using ohci and address 4 > usb 2-1.4: configuration #1 chosen from 1 choice > scsi 0:0:0:0: Direct-Access 0.00 PQ: 0 ANSI: 2 > sd 0:0:0:0: [sda] 7897088 512-byte logical blocks: (4.04 GB/3.76 GiB) > sd 0:0:0:0: [sda] Write Protect is off > sd 0:0:0:0: [sda] Assuming drive cache: write through > sd 0:0:0:0: [sda] Assuming drive cache: write through > sda: > sda1 > sd 0:0:0:0: [sda] Assuming drive cache: write through > sd 0:0:0:0: [sda] Attached SCSI removable disk > usb 2-1.4: USB disconnect, address 4 > usb 2-1.4: new full speed USB device using ohci and address 5 > hub 2-1:1.0: unable to enumerate USB device on port 4 > usb 2-1.4: new full speed USB device using ohci and address 6 > hub 2-1:1.0: unable to enumerate USB device on port 4 > usb 2-1.4: new full speed USB device using ohci and address 7 > hub 2-1:1.0: unable to enumerate USB device on port 4 > usb 2-1.4: new full speed USB device using ohci and address 8 > usb 2-1.4: device descriptor read/all, error -62 > hub 2-1:1.0: unable to enumerate USB device on port 4 > hub 2-1:1.0: unable to enumerate USB device on port 4 > usb 2-1.4: new full speed USB device using ohci and address 11 > usb 2-1.4: configuration #1 chosen from 1 choice > EXT3-fs warning: maximal mount count reached, running e2fsck is recommended > kjournald starting. Commit interval 5 seconds > EXT3 FS on sda1, internal journal > EXT3-fs: recovery complete. > EXT3-fs: mounted filesystem with writeback data mode. > VFS: Mounted root (ext3 filesystem) on device 8:1. > Freeing init memory: 148K > Warning: unable to open an initial console. > init: /init.rc: 119: invalid option 'setprop' > init: cannot open '/initlogo.rle' > init: cannot find '/system/bin/mountd', disabling 'mountd' > init: cannot find '/system/bin/playmp3', disabling 'bootsound' > init: cannot find '/system/etc/install-recovery.sh', disabling > 'flash_recovery' > # ls > etc > data > init > dev > sqlite_stmt_journals > sbin > cache > default.prop > proc > shared_prefs > system > sys > init.goldfish.rc > sdcard > init.rc > # warning: `app_process' uses 32-bit capabilities (legacy support in use) > usb 2-1.4: USB disconnect, address 11 > usb 2-1.4: new full speed USB device using ohci and address 12 > usb 2-1.4: configuration #1 chosen from 1 choice > usb 2-1.4: USB disconnect, address 12 > usb 2-1.4: new full speed USB device using ohci and address 13 > usb 2-1.4: configuration #1 chosen from 1 choice > usb 2-1.4: USB disconnect, address 13 > usb 2-1.4: new full speed USB device using ohci and address 14 > usb 2-1.4: configuration #1 chosen from 1 choice > hub 2-1:1.0: hub_port_status failed (err = -62) > hub 2-0:1.0: port 1 disabled by hub (EMI?), re-enabling... > usb 2-1: USB disconnect, address 2 > hub 2-1:1.0: cannot reset port 2 (err = -62) > usb 2-1.2: USB disconnect, address 3 > hub 2-1:1.0: cannot reset port 2 (err = -19) > hub 2-1:1.0: cannot disable port 2 (err = -19) > hub 2-1:1.0: cannot disable port 2 (err = -19) > sd 0:0:0:0: [sda] Unhandled error code > sd 0:0:0:0: [sda] Result: hostbyte=0x01 driverbyte=0x00 > sd 0:0:0:0: [sda] CDB: cdb[0]=0x28: 28 00 00 4d 4d 5e 00 00 18 00 > end_request: I/O error, dev sda, sector 5066078 > Aborting journal on device sda1. > ext3_abort called. > EXT3-fs error (device sda1): ext3_journal_start_sb: > EXT3-fs error (device sda1): ext3_find_entry: reading directory #183265 > offset 0 > Detected aborted journal > Remounting filesystem read-only > usb 2-1.4: USB disconnect, address 14 > EXT3-fs error (device sda1): ext3_find_entry: reading directory #95720 > offset 0 > EXT3-fs error (device sda1): ext3_find_entry: reading directory #95617 > offset 0 > usb 2-1: new full speed USB device using ohci and address 15 > usb 2-1: configuration #1 chosen from 1 choice > hub 2-1:1.0: USB hub found > hub 2-1:1.0: 4 ports detected > usb 2-1.2: new full speed USB device using ohci and address 16 > usb 2-1.2: not running at top speed; connect to a high speed hub > usb 2-1.2: configuration #1 chosen from 1 choice > scsi1 : SCSI emulation for USB Mass Storage devices > usb 2-1.4: new full speed USB device using ohci and address 17 > usb 2-1.4: configuration #1 chosen from 1 choice > EXT3-fs error (device sda1): ext3_find_entry: reading directory #143687 > offset 0 > EXT3-fs error (device sda1): ext3_find_entry: reading directory #143687 > offset 0 > EXT3-fs error (device sda1): ext3_find_entry: reading directory #143687 > offset 0 > scsi 1:0:0:0: Direct-Access 0.00 PQ: 0 ANSI: 2 > sd 1:0:0:0: [sdb] 7897088 512-byte logical blocks: (4.04 GB/3.76 GiB) > sd 1:0:0:0: [sdb] Write Protect is off > sd 1:0:0:0: [sdb] Assuming drive cache: write through > sd 1:0:0:0: [sdb] Assuming drive cache: write through > sdb: > sdb1 > sd 1:0:0:0: [sdb] Assuming drive cache: write through > sd 1:0:0:0: [sdb] Attached SCSI removable disk > EXT3-fs error (device sda1): ext3_find_entry: reading directory #95699 > offset 0 > ---------------------------------------------------------------------------------------------------------------------------- > Is that a problem from USB Hub.. -- unsubscribe: [email protected] website: http://groups.google.com/group/android-porting
