Hey Lucio, Can you share some details, I am not sure if I am getting it right.
Regards, Sagar Paul *E - [email protected] <https://groups.google.com/> GH - KB-perByte* On Friday, February 4, 2022 at 5:53:53 PM UTC+5:30 [email protected] wrote: > Hi Saga, > > Actually there is. > > The configuration is being applied using source templates. > > Regards, > > Lucio Jankok > > Op vr 4 feb. 2022 om 11:01 schreef Sagar Paul <[email protected]>: > >> >> Hey Lucio, >> as I see in the config that you have shared, there is no switchport or >> vlan data to parse as per the current scope of the module. >> Note - >> the interface data as shared in the above config is >> ``` >> interface GigabitEthernet0/0 >> vrf forwarding Mgmt-vrf >> no ip address >> shutdown >> negotiation auto >> ! >> interface GigabitEthernet1/0/1 >> no logging event link-status >> no cdp enable >> no snmp trap link-status >> source template redacted >> service-policy input redacted >> ! >> interface GigabitEthernet1/0/2 >> no logging event link-status >> shutdown >> no cdp enable >> no snmp trap link-status >> source template redacted >> service-policy input redacted >> ! >> ! >> interface GigabitEthernet1/0/24 >> shutdown >> ! >> interface GigabitEthernet1/1/1 >> ! >> interface GigabitEthernet1/1/2 >> ! >> interface GigabitEthernet1/1/3 >> ! >> interface GigabitEthernet1/1/4 ``` the module is supposed to generate >> blank facts for the device. Regards, Sagar Paul >> *E - [email protected] GH - KB-perByte* >> >> On Tuesday, February 1, 2022 at 9:14:29 PM UTC+5:30 [email protected] >> wrote: >> >>> Hi Sagar, >>> >>> The following is the case: >>> >>> *With the following platform I have no issues* >>> >>> platform: cisco WS-3850-24S >>> net_iostype: IOS-XE >>> net_version: 16.06.05 >>> >>> output: >>> net_interfaces - show me interface configuration per interface >>> net_neighbors - shows me Mac address etc for all connected devices >>> l2_interfaces - shows me interface name, switchport mode and access vlan >>> >>> --- >>> >>> *With the 9300 I don't get the complete l2_interfaces output* >>> >>> *platform: 9300-24p* >>> *net_iostype: IOS-XE* >>> *net_version: 17.03.03* >>> >>> net_interfaces - show me interface configuration per interface >>> net_neighbors - shows me Mac address etc for all connected devices >>> l2_interfaces - shows me only interface name. *missing switch port mode >>> and access vlan* >>> >>> ---- >>> >>> *Here is the redacted config for the 9300* >>> >>> Building configuration... >>> >>> >>> >>> Current configuration : 30751 bytes >>> >>> ! >>> >>> ! >>> >>> version 17.3 >>> >>> service tcp-keepalives-in >>> >>> service timestamps debug datetime msec localtime show-timezone >>> >>> service timestamps log datetime msec localtime show-timezone >>> >>> service password-encryption >>> >>> service compress-config >>> >>> service call-home >>> >>> no platform punt-keepalive disable-kernel-core >>> >>> ! >>> >>> hostname redacted >>> >>> ! >>> >>> ! >>> >>> vrf definition Mgmt-vrf >>> >>> ! >>> >>> address-family ipv4 >>> >>> exit-address-family >>> >>> ! >>> >>> address-family ipv6 >>> >>> exit-address-family >>> >>> ! >>> >>> logging discriminator CFGLOG mnemonics drops CFGLOG_LOGGEDCMD >>> >>> logging buffered discriminator CFGLOG 16384 informational >>> >>> no logging console >>> >>> enable secret 9 redacted >>> >>> ! >>> >>> aaa new-model >>> >>> ! >>> >>> ! >>> >>> aaa group server tacacs+ AUTH >>> >>> server name redacted >>> >>> server name redacted >>> >>> ip tacacs source-interface redacted >>> >>> ! >>> >>> aaa authentication password-prompt "Local Password: " >>> >>> aaa authentication username-prompt "Local Username: " >>> >>> aaa authentication login default group AUTH local >>> >>> aaa authentication enable default group AUTH enable >>> >>> aaa authorization console >>> >>> aaa authorization config-commands >>> >>> aaa authorization exec default group AUTH local >>> >>> aaa authorization commands 1 default group AUTH if-authenticated >>> >>> aaa authorization commands 15 default group AUTH if-authenticated >>> >>> aaa accounting exec default start-stop group AUTH >>> >>> aaa accounting commands 15 default stop-only group AUTH >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> aaa session-id common >>> >>> boot system switch all flash:packages.conf >>> >>> clock timezone CET 1 0 >>> >>> clock summer-time CEST recurring last Sun Mar 2:00 last Sun Oct 3:00 >>> >>> switch 1 provision c9300-24p >>> >>> switch 2 provision c9300-24p >>> >>> software auto-upgrade enable >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> no ip domain lookup >>> >>> ip domain name redacted >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> ip dhcp snooping vlan redacted >>> >>> no ip dhcp snooping information option >>> >>> ip dhcp snooping >>> >>> login on-success log >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> vtp mode off >>> >>> udld enable >>> >>> >>> >>> no device-tracking logging theft >>> >>> password encryption aes >>> >>> ! >>> >>> source template redacted >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> port-channel load-balance src-dst-ip >>> >>> license boot level network-advantage addon dna-advantage >>> >>> license smart url cslu redacted >>> >>> ! >>> >>> ! >>> >>> diagnostic bootup level complete >>> >>> ! >>> >>> spanning-tree mode rapid-pvst >>> >>> spanning-tree portfast bpduguard default >>> >>> spanning-tree extend system-id >>> >>> spanning-tree pathcost method long >>> >>> archive >>> >>> log config >>> >>> logging enable >>> >>> notify syslog contenttype plaintext >>> >>> path redacted >>> >>> write-memory >>> >>> memory free low-watermark processor 133138 >>> >>> ! >>> >>> errdisable recovery cause udld >>> >>> errdisable recovery cause bpduguard >>> >>> errdisable recovery cause channel-misconfig >>> >>> errdisable recovery cause link-flap >>> >>> errdisable recovery cause gbic-invalid >>> >>> errdisable recovery cause psecure-violation >>> >>> errdisable recovery cause loopback >>> >>> errdisable recovery interval 600 >>> >>> username redacted privilege 15 secret 9 redacted >>> >>> ! >>> >>> redundancy >>> >>> mode sso >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> ! >>> >>> transceiver type all >>> >>> monitoring >>> >>> hw-switch switch 1 logging onboard message >>> >>> ! >>> >>> vlan redacted >>> >>> name redacted >>> >>> ! >>> >>> vlan redacted >>> >>> name redacted >>> >>> ! >>> >>> ! >>> >>> template redacted >>> >>> spanning-tree portfast >>> >>> switchport access vlan redacted >>> >>> switchport mode access >>> >>> load-interval 30 >>> >>> description redacted >>> >>> ! >>> >>> ! >>> >>> interface GigabitEthernet0/0 >>> >>> vrf forwarding Mgmt-vrf >>> >>> no ip address >>> >>> shutdown >>> >>> negotiation auto >>> >>> ! >>> >>> interface GigabitEthernet1/0/1 >>> >>> no logging event link-status >>> >>> no cdp enable >>> >>> no snmp trap link-status >>> >>> source template redacted >>> >>> service-policy input redacted >>> >>> ! >>> >>> interface GigabitEthernet1/0/2 >>> >>> no logging event link-status >>> >>> shutdown >>> >>> no cdp enable >>> >>> no snmp trap link-status >>> >>> source template redacted >>> >>> service-policy input redacted >>> >>> ! >>> >>> ! >>> >>> interface GigabitEthernet1/0/24 >>> >>> shutdown >>> >>> ! >>> >>> interface GigabitEthernet1/1/1 >>> >>> ! >>> >>> interface GigabitEthernet1/1/2 >>> >>> ! >>> >>> interface GigabitEthernet1/1/3 >>> >>> ! >>> >>> interface GigabitEthernet1/1/4 >>> >>> ! >>> >>> i >>> >>> ! >>> >>> line con 0 >>> >>> exec-timeout 30 0 >>> >>> logging synchronous >>> >>> stopbits 1 >>> >>> line vty 0 4 >>> >>> access-class ACL-VTY in >>> >>> exec-timeout 30 0 >>> >>> logging synchronous >>> >>> transport input ssh >>> >>> line vty 5 31 >>> >>> access-class ACL-VTY in >>> >>> exec-timeout 30 0 >>> >>> logging synchronous >>> >>> no exec >>> >>> transport input ssh >>> >>> ! >>> >>> end >>> >>> >>> Op ma 31 jan. 2022 om 13:36 schreef Sagar Paul <[email protected]>: >>> >>>> Hi Lucio, >>>> >>>> Can you please share the config that is not giving facts data? >>>> >>>> Regards, >>>> Sagar Paul >>>> >>>> On Friday, January 28, 2022 at 10:25:49 PM UTC+5:30 [email protected] >>>> wrote: >>>> >>>>> Hi, >>>>> >>>>> When I use the gather fact module and choose to get the l2_interfaces, >>>>> it doesn't return the l2_interfaces properties. >>>>> When I use the same playbook on catalyst 3650 (also ios-xe) I get the >>>>> l2_interfaces properties. >>>>> >>>>> Is this a known issue? >>>>> >>>>> Regards, >>>>> >>>>> Lucio Jankok >>>>> >>>> -- >>>> You received this message because you are subscribed to the Google >>>> Groups "Ansible Project" group. >>>> To unsubscribe from this group and stop receiving emails from it, send >>>> an email to [email protected]. >>>> To view this discussion on the web visit >>>> https://groups.google.com/d/msgid/ansible-project/674592ac-b9c5-4b76-abba-7b3ebb720819n%40googlegroups.com >>>> >>>> <https://groups.google.com/d/msgid/ansible-project/674592ac-b9c5-4b76-abba-7b3ebb720819n%40googlegroups.com?utm_medium=email&utm_source=footer> >>>> . >>>> >>> -- >> You received this message because you are subscribed to the Google Groups >> "Ansible Project" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> > To view this discussion on the web visit >> https://groups.google.com/d/msgid/ansible-project/3cc4277a-a976-447d-ba2d-255a7cc9525en%40googlegroups.com >> >> <https://groups.google.com/d/msgid/ansible-project/3cc4277a-a976-447d-ba2d-255a7cc9525en%40googlegroups.com?utm_medium=email&utm_source=footer> >> . >> > -- You received this message because you are subscribed to the Google Groups "Ansible Project" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/ansible-project/a4aa1ce9-2642-4e80-bd96-cfade4b307aen%40googlegroups.com.
