Thomas Bächler wrote:
> Good morning,
>
> just a few minutes ago, the 2.6.22 kernel has been submitted to the
> testing repository. Please test it and report any bugs that might occur,
> so we hopefully can move it to current within a week.
> This kernel will also be the basis of the "Archlinux 2007.07 Don't
> panic" snapshot.
>
I gave it a shot last night and got an error irq 10: nobody cared.
trying the suggested irqpoll option didn't make a difference either.
One of my drives didn't have dma and the usb mouse was screwy for lack
of a better word. I guess that makes sense since the ide and usb
controllers are on that irq. I made no changes to the bios etc.
----------------------------------------------------------------
Dmesg:
Linux version 2.6.22-ARCH ([EMAIL PROTECTED]) (gcc version 4.2.1 20070704
(prerelease)) #1 SMP PREEMPT Mon Jul 9 23:34:30 CEST 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000027ff0000 (usable)
BIOS-e820: 0000000027ff0000 - 0000000027ff3000 (ACPI NVS)
BIOS-e820: 0000000027ff3000 - 0000000028000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
639MB LOWMEM available.
Entering add_active_range(0, 0, 163824) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 163824
HighMem 163824 -> 163824
early_node_map[1] active PFN ranges
0: 0 -> 163824
On node 0 totalpages: 163824
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1247 pages used for memmap
Normal zone: 158481 pages, LIFO batch:31
HighMem zone: 0 pages used for memmap
DMI 2.2 present.
ACPI: RSDP 000F76C0, 0014 (r0 VIA694)
ACPI: RSDT 27FF3000, 0028 (r1 VIA694 AWRDACPI 42302E31 AWRD 0)
ACPI: FACP 27FF3040, 0074 (r1 VIA694 AWRDACPI 42302E31 AWRD 0)
ACPI: DSDT 27FF30C0, 244C (r1 VIA694 AWRDACPI 1000 MSFT 100000C)
ACPI: FACS 27FF0000, 0040
ACPI: PM-Timer IO Port: 0x4008
Allocating PCI resources starting at 30000000 (gap: 28000000:d7ff0000)
Built 1 zonelists. Total pages: 162545
Kernel command line: root=/dev/disk/by-label/root ro irqpoll
Misrouted IRQ fixup and polling support enabled
This may significantly impact system performance
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (0150f000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1399.655 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 644268k/655296k available (2380k kernel code, 10376k reserved,
787k data, 304k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfff82000 - 0xfffff000 ( 500 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xe8800000 - 0xff7fe000 ( 367 MB)
lowmem : 0xc0000000 - 0xe7ff0000 ( 639 MB)
.init : 0xc041f000 - 0xc046b000 ( 304 kB)
.data : 0xc03533df - 0xc04181bc ( 787 kB)
.text : 0xc0100000 - 0xc03533df (2380 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2807.52 BogoMIPS
(lpj=4677635)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff c1c3f9ff 00000000 00000000
00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383f9ff c1c3f9ff 00000000 00000420 00000000
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 11k freed
Early unpacking initramfs... done
ACPI: Core revision 20070126
ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
ACPI: setting ELCR to 0020 (from 1e20)
CPU0: AMD Athlon(tm) XP 1600+ stepping 02
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb240, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Disabling VIA memory write queue (PCI ID 0305, rev 03): [55] 89 & 1f -> 09
PCI quirk: region 6000-607f claimed by vt82c686 HW-mon
PCI quirk: region 5000-500f claimed by vt82c686 SMB
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *9
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 12 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:00: iomem range 0xcd600-0xcffff has been reserved
pnp: 00:00: iomem range 0xf0000-0xf7fff could not be reserved
pnp: 00:00: iomem range 0xf8000-0xfbfff could not be reserved
pnp: 00:00: iomem range 0xfc000-0xfffff could not be reserved
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: dc000000-ddffffff
PREFETCH window: d0000000-d7ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 600k freed
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Applying VIA southbridge workaround.
PCI: VIA PCI bridge detected. Disabling DAC.
PCI: Disabling Via external APIC routing
Boot video device is 0000:01:00.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: module loaded
input: Macintosh mouse button emulation as /class/input/input0
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
Switched to high resolution mode on CPU 0
input: AT Translated Set 2 keyboard as /class/input/input1
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
Freeing unused kernel memory: 304k freed
libata version 2.21 loaded.
pata_via 0000:00:07.1: version 0.3.1
scsi0 : pata_via
scsi1 : pata_via
ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001c000
irq 14
ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001c008
irq 15
ata1.00: ATAPI: PLEXTOR CD-R PX-W2410A, 1.02, max UDMA/33
ata1.01: ATAPI: E-IDE 10X DVD-ROM DRIVE 0125, E1.25, max UDMA/33
ata1.00: configured for UDMA/33
ata1.01: configured for UDMA/33
ata2.00: ATA-5: WDC WD400BB-00CAA1, 17.07W17, max UDMA/100
ata2.00: 78165360 sectors, multi 16: LBA
ata2.00: limited to UDMA/33 due to 40-wire cable
ata2.00: configured for UDMA/33
scsi 0:0:0:0: CD-ROM PLEXTOR CD-R PX-W2410A 1.02 PQ: 0 ANSI: 5
scsi 0:0:1:0: CD-ROM IDE 10X DVD-ROM 1.25 PQ: 0 ANSI: 5
scsi 1:0:0:0: Direct-Access ATA WDC WD400BB-00CA 17.0 PQ: 0 ANSI: 5
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
CMD649: IDE controller at PCI slot 0000:00:10.0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKD] -> GSI 10 (level,
low) -> IRQ 10
CMD649: chipset revision 2
CMD649: 100% native mode on irq 10
ide0: BM-DMA at 0xe400-0xe407, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xe408-0xe40f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: WDC WD1600JB-00GVA0, ATA DISK drive
hda: selected mode 0x45
ide0 at 0xd400-0xd407,0xd802 on irq 10
Probing IDE interface ide1...
hdc: WDC WD1600JB-00GVA0, ATA DISK drive
hdc: selected mode 0x45
ide1 at 0xdc00-0xdc07,0xe002 on irq 10
hda: max request size: 512KiB
hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63,
UDMA(100)
hda: cache flushes supported
hda: hda1
sd 1:0:0:0: [sda] 78165360 512-byte hardware sectors (40021 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 1:0:0:0: [sda] 78165360 512-byte hardware sectors (40021 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sda:<6>hdc: max request size: 512KiB
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sda1 sda2 sda3
hdc: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63,
UDMA(100)
sr 0:0:0:0: Attached scsi CD-ROM sr0
sd 1:0:0:0: [sda] Attached SCSI disk
hdc: cache flushes supported
hdc: hdc1
sr1: scsi3-mmc drive: 0x/0x cd/rw xa/form2 cdda tray
sr 0:0:1:0: Attached scsi CD-ROM sr1
irq 10: nobody cared (try booting with the "irqpoll" option)
[<c0157434>] __report_bad_irq+0x24/0x80
[<c01576f1>] note_interrupt+0x261/0x2a0
[<e886a9d0>] ide_dma_intr+0x0/0xc0 [ide_core]
[<c01582b1>] handle_level_irq+0xa1/0x110
[<c0106f4b>] do_IRQ+0x3b/0x70
[<e882d568>] ata_interrupt+0xe8/0x220 [libata]
[<c02b4498>] i8042_interrupt+0x1e8/0x260
[<c0104da3>] common_interrupt+0x23/0x28
[<c01309f0>] __do_softirq+0x60/0x110
[<c0130af5>] do_softirq+0x55/0x60
[<c0130d79>] irq_exit+0x79/0x90
[<c0106f50>] do_IRQ+0x40/0x70
[<c014251e>] ktime_get_ts+0x1e/0x60
[<c0104da3>] common_interrupt+0x23/0x28
[<c0120692>] native_safe_halt+0x2/0x10
[<c0102c1d>] default_idle+0x3d/0x60
[<c0102433>] cpu_idle+0x73/0xe0
[<c041fa75>] start_kernel+0x315/0x3a0
[<c041f1f0>] unknown_bootoption+0x0/0x260
=======================
handlers:
[<e8862c70>] (ide_intr+0x0/0x210 [ide_core])
[<e8862c70>] (ide_intr+0x0/0x210 [ide_core])
Disabling IRQ #10
hdc: dma_timer_expiry: dma status == 0x24
hdc: DMA timeout error
hdc: dma timeout error: status=0x50 { DriveReady SeekComplete }
ide: failed opcode was: unknown
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Linux agpgart interface v0.102 (c) Dave Jones
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 12
PCI: setting IRQ 12 as level-triggered
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 12 (level,
low) -> IRQ 12
NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-9639 Mon Apr 16
20:20:06 PDT 2007
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 2 throttling states)
Marking TSC unstable due to: possible TSC halt in C2.
Time: acpi_pm clocksource has been installed.
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 10 (level,
low) -> IRQ 10
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 10, io base 0x0000c400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI 10 (level,
low) -> IRQ 10
uhci_hcd 0000:00:07.3: UHCI Host Controller
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:07.3: irq 10, io base 0x0000c800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-1: new full speed USB device using uhci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378 (0x778), irq 7, using FIFO
[PCSPP,TRISTATE,COMPAT,ECP]
parport_pc: VIA parallel port: io=0x378, irq=7
sr 0:0:0:0: Attached scsi generic sg0 type 5
sr 0:0:1:0: Attached scsi generic sg1 type 5
sd 1:0:0:0: Attached scsi generic sg2 type 0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
natsemi dp8381x driver, version 2.1, Sept 11, 2006
originally by Donald Becker <[EMAIL PROTECTED]>
2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKB] -> GSI 11 (level,
low) -> IRQ 11
natsemi eth0: NatSemi DP8381[56] at 0xdf000000 (0000:00:0a.0),
00:40:f4:4c:f3:cb, IRQ 11, port TP.
agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
agpgart: AGP aperture is 64M @ 0xd8000000
rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k
PPP generic driver version 2.4.2
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LNKC] -> GSI 11 (level,
low) -> IRQ 11
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
usbcore: registered new interface driver hiddev
input: PC Speaker as /class/input/input4
input: Logitech USB Gaming Mouse as /class/input/input5
input: USB HID v1.11 Mouse [Logitech USB Gaming Mouse] on usb-0000:00:07.2-1
hiddev0: USB HID v1.11 Device [Logitech USB Gaming Mouse] on
usb-0000:00:07.2-1
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
hdc: dma_timer_expiry: dma status == 0x24
hdc: DMA timeout error
hdc: dma timeout error: status=0x50 { DriveReady SeekComplete }
ide: failed opcode was: unknown
hdc: dma_timer_expiry: dma status == 0x24
hdc: DMA timeout error
hdc: dma timeout error: status=0x50 { DriveReady SeekComplete }
ide: failed opcode was: unknown
EXT3 FS on sda3, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with journal data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdc1, internal journal
EXT3-fs: mounted filesystem with journal data mode.
Adding 262576k swap on /dev/sda2. Priority:-1 extents:1 across:262576k
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
eth0: no IPv6 routers present
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
sr1: CDROM not ready. Make sure there is a disc in the drive.
_______________________________________________
arch mailing list
[email protected]
http://archlinux.org/mailman/listinfo/arch
