Trying to boot the Fedora-Minimal-armhfp-rawhide-20140320-sda image I downloaded from koji today, looked like the 20140321 builds failed just gives me a blank screen. Here's the console output from booting their Ubuntu image:
U-Boot 2013.10-rc3 (Jan 20 2014 - 13:33:34) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Board: UDOO DRMMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment Display: HDMI (1024x768) using phy at 6 0 mmc0 is current device ** File not found boot.scr ** ** File not found imx6q-udoo.dtb ** ## Booting kernel from Legacy Image at 12000000 ... Image Name: Linux-3.0.35 ImaOK Loading Kernel Image ... OK [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.0.35 (udoo@ubuntu) (gcc version 4.4.4 (4.4.4_09.0.MX6Q, silicon rev 1.2 [ 0.000000] PERCPU: Embedded 7 pages/cpu @8c008000 s5504 r8192 d14976 u32768 [ 0.000000] Built 1-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 640MB 256MB = 896MB total [ 0.000000] Mem] lowmem : 0x80000000 - 0xc0000000 (1024 MB) [ 0.000000] pkmap : 0x7fe00000 - 0x80000000 ( 2 MB) [ 0.0jects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:624 [ 0.00000_max_freq=1GHz [ 0.000000] MXC_Early serial console at MMIO 0x21e8000 (options '115200') [ 0.000000] bootconsole [ttymx1581.05 BogoMIPS (lpj=7905280) [ 0.306189] pid_max: default: 32768 minimum: 301 [ 0.311083] Mount-cache hash table entries: 512 [ 0.316337] Initializing cgroup subsys cpuacct [ 0.320836] Initializing cgroup subsys devices [ 0.325295] Initializi[ 0.339285] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available [ 0.661960] devtmpfs: initialized [ 0.682033] print_constraints: dummy: [ 0.694875] print_constraints: vddpu: 725 <--> 1300 mV at 1150 mV fast normal [ 0.710201] print_constraints: vddsoc: 725 <--> 1300 mV at 1200 mV fast normal [ 0.717873] print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal [ 0.725645] print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal [ 0.742432] [ 0.742439] > UDOO quad [ 0.746211] > rev C Called set_gpios_direction [ 0.750892] Test and set gpi[ 0.782777] Resetting ethernet physical layer. [ 1.152507] PMU: registered new PMU device of type 0 [ 1.271940] mxc_hdmi mxc_hdmi: Detected HDMI controller 0x13:0xa:0xa0:0xc1 [ 1.278864] fbcvt: 1920x1080@60: CVT Name - 2[ 1.302489] imx-ipuv3 imx-ipuv3.0: WARNING: adapt panel end blank lines [ 1.317514] imx-ipuv3 imx-ipuv3.0: IPU DMFC DP H[ 1.823568] request BOSSA_CLK IRQ [ 1.826889] registering IRQ 419 for BOSSAC Arduino erase/reset operation [ 1.991597] add wake up source irq 72 [ 1.995294] fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller [ 2.00[ 2.077455] fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00 [ 2.096694] usbcore: registered new interface driver usb-storage [ 2.102746] USB Mass Storage support registered. [ 2.129807] USB Serial support registered for debug [ 2.146599] g_ether gadget: using random self ethernet address [ 2.152460] g_ether gadget: using random host ethernet adal Day 2008 [ 2.182562] g_ether gadget: g_ether ready [ 2.186609] Suspend udc for OTG auto detect [ 2.207546] fsl-usb2-udc: bind to driver g_ether [ 2.218789] usbcore: registered new interface driver usbtouchscreen [ 2.225485] Sitronix touch driver 2.9.1 [ 2.229338] Release date: 20120507 [ 2.233124] sitronix_reset_ic [ 2.356326] send status reg command error (-5) [ 2.360793] sitronix: probe of 2-0055 failed with error -5 [ 2.366715] i2c-core: driver [isl29023] using legacy suspend method [ 2.373002] i2c-core: driver [isl29023] using legacy[ 2.386555] i2c /dev entries driver [ 2.390859] Linux video capture interface: v2.00 [ 2.427478] usb 2-1: new high speed USB device number 2 using fsl-ehci [ 2.527550] ov5640_read_reg:write reg error:reg=300a [ 2.532517] camera ov5640_mipi is not found [ 2.544781] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video17 [ 2.552426] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video18 [ 2.567722] mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video20 [ 2.589851] usbcore: registered new interface driver uvcvideo [ 2.595615] USB Video Class driver (v1.1.0) [ 2.621197] imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1) [ 2.634366] Bluetooth: HCI UART driver ver 2.2 [ 2.638828] Bluetooth: HCIATH3K protocol initialized [ 2.643794] Blue[ 2.655170] sdhci: Secure Digital Host Controller Interface driver [ 2.661366] sdhci: Copyright(c) Pierre Ossman [ 2.666036] mmc0: SDHCI controller on platform [sdhci-esdhc-imx.2] using DMA [ 2.673376] mxc_vdoa mxc_vdoa: i.MX Video Data Order Adapter(VDOA) driver probed [ 2.684594] VPU initialized [ 2.712865] Thermal calibration data is 0x5534be69 [ 2.717679] Thermal sensor with ratio = 175 [ 2.737465] Anatop Thermal registered as thermal_zone0 [ 2.751946] usbcore: registered new interface driver usbhid [ 2.757638] usbhid: USB HID core driver [ 2.761989] usbcore: registered new interface driver snd-usb-audio [ 2.768746] mxc_hdmi_soc mxc_hdmi_soc.0: MXC HDMI Audio [ 2.779478] i2c-core: driver [cs42888] using legacy suspend method [ 2.785661] i2c-core: driver [cs42888] using legacy r[ 2.829740] mmcblk0: mmc0:e624 SU16G 14.8 GiB [ 2.838731] mmcblk0: p1 p2 < p5 > [ 2.927910] usb 2-1.1: new full speed USB device number 3 using fsl-ehci [ 2.960034] Found Audio codec AC97 vt1613, [ID = 5649 - 4123] [ 2.984600] imx_3stack asoc driver [ 2.996289] ALSA device list: [ 3.010720] TCP cubic registered [ 3.013952] NET: Registered protocol family 17 [ 3.018451] can: controller area net[ 3.039209] Bluetooth: RFCOMM TTY layer initialized [ 3.044096] Bluetooth: RFCOMM socket layer initialized [ 3.04924sl-ehci.1-1.1/input0 [ 3.066827] input: Logitech USB Receiver as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.1/2-1.1:1.1/inpuhci.1-1.1/input1 [ 3.071063] generic-usb 0003:046D:C52B.0003: hidraw2: USB HID v1.11 Device [Logitech USB Receiver] on usb-[ 3.125305] lib8 0211: common routines for IEEE802.11 drivers [ 3.131006] Registering the dns_resolver key type [ 3.1[ 3.143816] Bus freq driver module loaded [ 3.147886] Bus freq driver Enabled [ 3.153165] mxc_dvfs_core_probe [ 3.161847] snvs_rtc snvs_rtc.0: setting system clock to 1970-01-01 00:00:00 UTC (0) On Fri, Mar 21, 2014 at 12:03 PM, Peter Robinson <[email protected]>wrote: > On Thu, Mar 20, 2014 at 7:28 AM, Jason Porter <[email protected]> > wrote: > > I received an UDOO today (looking through the list, it looks like I would > > have been better off with a Wandboard for the power (except for the > Arduino > > stuff, so that's good) oh well :) Anyway, I tried their Ubuntu images and > > I'm simply not happy with them. It's been a while since I've used Ubuntu > > (been using Fedora pretty much since I started at Red Hat), things are > > unfamiliar and honestly they don't quite work right. I'd like to use > Fedora, > > but it looks like support is only in Rawhide at the moment. I'm really > not > > all that concerned with using Rawhide (though if I could backport > support to > > Fedora 20 that would be awesome), I just don't know where to start. Could > > anyone give me any pointers or some links on how to get started, please? > > Just to cover this here for reference too (also discussed on G+) > > The rawhide nightlies should work with the UDOO, it's possible we > might need to poke a few bits to ensure it gets the right DT blob. If > it doesn't boot straight off can you get all of the console output of > uboot plus the output of the printenv and help commands and we'll add > the bits needed. The dtb is imx6q-udoo.dtb > > Peter > -- Jason Porter http://en.gravatar.com/lightguardjp
_______________________________________________ arm mailing list [email protected] https://admin.fedoraproject.org/mailman/listinfo/arm
