Is there some place to watch for that build, or is this list the best place?
On Mon, Mar 24, 2014 at 1:05 PM, Peter Robinson <[email protected]>wrote: > On Sun, Mar 23, 2014 at 9:46 PM, Jason Porter <[email protected]> > wrote: > > Hey Peter, hope this is a bit more helpful: > > Looks good, the next release of arm-boot-config will add the needed > support. > > Thanks for the details, > > Peter > > > U-Boot 2013.10-rc3 (Jan 20 2014 - 13:33:34) > > > > CPU: Freescale i.MX6Q rev1.2 at 792 MHz > > Reset cause: POR > > Board: UDOO > > DRAM: 1 GiB > > MMC: FSL_SDHC: 0 > > *** Warning - bad CRC, using default environment > > > > auto-detected panel HDMI > > Display: HDMI (1024x768) > > In: serial > > Out: serial > > Err: serial > > Net: using phy at 6 > > FEC [PRIME] > > Hit any key to stop autoboot: 0 > > UDOO board => help > > ? - alias for 'help' > > base - print or set address offset > > bdinfo - print Board Info structure > > boot - boot default, i.e., run 'bootcmd' > > bootd - boot default, i.e., run 'bootcmd' > > bootm - boot application image from memory > > bootp - boot image via network using BOOTP/TFTP protocol > > bootz - boot Linux zImage image from memory > > clocks - display clocks > > clrlogo - fill the boot logo area with black > > cmp - memory compare > > coninfo - print console devices and information > > cp - memory copy > > crc32 - checksum calculation > > dcache - enable or disable data cache > > dhcp - boot image via network using DHCP/TFTP protocol > > echo - echo args to console > > editenv - edit environment variable > > env - environment handling commands > > erase - erase FLASH memory > > exit - exit script > > ext2load- load binary file from a Ext2 filesystem > > ext2ls - list files in a directory (default /) > > false - do nothing, unsuccessfully > > fatinfo - print information about filesystem > > fatload - load binary file from a dos filesystem > > fatls - list files in a directory (default /) > > fdt - flattened device tree utility commands > > flinfo - print FLASH memory information > > go - start application at address 'addr' > > hdmidet - detect HDMI monitor > > help - print command description/usage > > icache - enable or disable instruction cache > > iminfo - print header information for application image > > imxtract- extract a part of a multi-image > > itest - return true/false on integer compare > > loadb - load binary file over serial line (kermit mode) > > loads - load S-Record file over serial line > > loadx - load binary file over serial line (xmodem mode) > > loady - load binary file over serial line (ymodem mode) > > loop - infinite loop on address range > > md - memory display > > mdio - MDIO utility commands > > mii - MII utility commands > > mm - memory modify (auto-incrementing address) > > mmc - MMC sub system > > mmcinfo - display MMC info > > multiboot- manage a multiboot startup > > mw - memory write (fill) > > nfs - boot image via network using NFS protocol > > nm - memory modify (constant address) > > ping - send ICMP ECHO_REQUEST to network host > > plotmsg - Plot text message on current display (HDMI or LVDS). > > -r Overwrite last message. > > -u Start writing just under Logo. > > printenv- print environment variables > > protect - enable or disable FLASH write protection > > reset - Perform RESET of the CPU > > run - run commands in an environment variable > > sata - SATA sub system > > saveenv - save environment variables to persistent storage > > setenv - set environment variables > > setexpr - set environment variable as the result of eval expression > > showvar - print local hushshell variables > > sleep - delay execution for some time > > source - run script from memory > > test - minimal test like /bin/sh > > tftpboot- boot image via network using TFTP protocol > > true - do nothing, successfully > > version - print monitor, compiler and linker version > > UDOO board => printenv > > baudrate=115200 > > boot_fdt=try > > bootcmd=mmc dev ${mmcdev}; if mmc rescan; then if run loadbootscript; > then > > run bootscript; else if run loaduimage; then run mmcbooi > > bootdelay=5 > > bootscript=echo Running bootscript from mmc ...; source > > console=ttymxc1 > > ethact=FEC > > ethaddr=00:c0:08:88:a2:a2 > > ethprime=FEC > > fdt_addr=0x11000000 > > fdt_file=imx6q-udoo.dtb > > fdt_high=0xffffffff > > initrd_high=0xffffffff > > ip_dyn=yes > > loadaddr=0x12000000 > > loadbootscript=ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script}; > > loadfdt=ext2load mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file} > > loaduimage=ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage} > > mmcargs=setenv bootargs console=${console},${baudrate} root=${mmcroot} > > ${hdmi_patch} fbmem=24M video=mxcfb0:dev=hdmi,1920x1080M@602 > > mmcboot=echo Booting from mmc ...; run mmcargs; if test ${boot_fdt} = > yes || > > test ${boot_fdt} = try; then if run loadfdt; then boo; > > mmcdev=0 > > mmcpart=1 > > mmcroot=/dev/mmcblk0p1 rootwait rw > > netargs=setenv bootargs console=${console},${baudrate} root=/dev/nfs > > ${hdmi_patch} ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp > > netboot=echo Booting from net ...; run netargs; if test ${ip_dyn} = yes; > > then setenv get_cmd dhcp; else setenv get_cmd tftp; fi; $; > > script=boot.scr > > splashpos=m,m > > uimage=/boot/uImage > > update_sd_firmware=if test ${ip_dyn} = yes; then setenv get_cmd dhcp; > else > > setenv get_cmd tftp; fi; if mmc dev ${mmcdev}; then if i > > update_sd_firmware_filename=u-boot.imx > > > > Environment size: 2075/8188 bytes > > UDOO board => iminfo > > > > ## Checking Image at 12000000 ... > > Unknown image format! > > UDOO board => md > > md - memory display > > > > Usage: > > md [.b, .w, .l] address [# of objects] > > UDOO board => mmcinfo > > Device: FSL_SDHC > > Manufacturer ID: 3 > > OEM: 5344 > > Name: SU16G > > Tran Speed: 50000000 > > Rd Block Len: 512 > > SD version 3.0 > > High Capacity: Yes > > Capacity: 14.8 GiB > > Bus Width: 4-bit > > UDOO board => showvar > > HUSH_VERSION=0.01 > > UDOO board => > > > > > > > > On Sun, Mar 23, 2014 at 7:41 AM, Peter Robinson <[email protected]> > > wrote: > >> > >> On Sat, Mar 22, 2014 at 2:25 AM, Jason Porter <[email protected]> > >> wrote: > >> > Trying to boot the Fedora-Minimal-armhfp-rawhide-20140320-sda image I > >> > downloaded from koji today, looked like the 20140321 builds failed > just > >> > gives me a blank screen. Here's the console output from booting their > >> > Ubuntu > >> > image: > >> > >> Not much help. Can you interrupt the boot during the uboot phase (ie > >> before it says "Booting kernel from Legacy Image") and then at the > >> uboot prompt type: > >> help <press enter> > >> printenv <press enter> > >> > >> And the take a copy of all the output for us. The above is using an > >> ancient kernel without DT support and is ancient history ;-) > >> > >> Peter > > > > > > > > > > -- > > Jason Porter > > http://en.gravatar.com/lightguardjp > -- Jason Porter http://en.gravatar.com/lightguardjp
_______________________________________________ arm mailing list [email protected] https://admin.fedoraproject.org/mailman/listinfo/arm
