Corrected:
# more /etc/hostname.dwxe0
inet 192.168.1.9 255.255.255.0
#
Now:
dwxe0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr 02:81:b1:07:76:5e
index 1 priority 0 llprio 3
groups: egress
media: Ethernet none (none loopback)
status: active
inet 192.168.1.9 netmask 0xffffff00 broadcast 192.168.1.255
But if I try to set media options I get a media error.
From: Stephen Graf [mailto:[email protected]]
Sent: Wednesday, September 27, 2017 9:55 AM
To: '[email protected]' <[email protected]>
Subject: help with setting up dwxe on orange pi one (h3)
I am trying to test the dwxe driver on my orange pi one, an Allwinner h3
device. Any help is appreciated.
I took the dtb entries from an Armbian system that runs on this device:
ethernet@1c30000 {
compatible = "allwinner,sun8i-h3-emac";
syscon = <0x6>;
reg = <0x1c30000 0x104>;
interrupts = <0x0 0x52 0x4>;
resets = <0x2 0xc>;
reset-names = "ahb";
clocks = <0x2 0x1b>;
clock-names = "ahb";
#address-cells = <0x1>;
#size-cells = <0x0>;
status = "okay";
phy-handle = <0x7>;
phy-mode = "mii";
allwinner,leds-active-low;
linux,phandle = <0x31>;
phandle = <0x31>;
mdio {
#address-cells = <0x1>;
#size-cells = <0x0>;
linux,phandle = <0x32>;
phandle = <0x32>;
ethernet-phy@1 {
reg = <0x1>;
clocks = <0x2 0x43>;
resets = <0x2 0x27>;
linux,phandle = <0x47>;
phandle = <0x47>;
};
};
};
pinctrl@01c20800 {
emac0 {
pins = "PD0", "PD1", "PD2", "PD3", "PD4",
"PD5", "PD7", "PD8", "PD9", "PD10", "PD12", "PD13", "PD15", "PD16", "PD17";
function = "emac";
drive-strength = <0x28>;
};
The device is recognized at boot time:
dwxe0 at simplebus0: address 02:81:b1:07:76:5e
ukphy0 at dwxe0 phy 0: Generic IEEE 802.3u media interface, rev. 4: OUI
0x1e7a40, model 0x0004
ukphy1 at dwxe0 phy 1: Generic IEEE 802.3u media interface, rev. 4: OUI
0x1e7240, model 0x0004
ifmedia_set: no match for 0x100/0xffffffffffffffff
The orange pi one does not support 1000 Mhz.
I set up
# more /etc/hostname.dwxe0
ifconfig dwxe0 192.168.1.9 up netmask 255.255.255.0 media 100baseTX
but on boot get:
ifconfig: ifconfig: bad value
dhclient turns on the yellow LAN connector status light:
# dhclient dwxe0
dwxe0: DHCPDISCOVER - interval 1
dwxe0: DHCPDISCOVER - interval 1
dwxe0: DHCPDISCOVER - interval 2
dwxe0: DHCPDISCOVER - interval 4
dwxe0: DHCPDISCOVER - interval 6
dwxe0: DHCPDISCOVER - interval 8
dwxe0: DHCPDISCOVER - interval 9
dwxe0: no acceptable DHCPOFFERS received
dwxe0: no working leases in persistent database sleeping
# ifconfig dwxe0
dwxe0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr 02:81:b1:07:76:5e
index 1 priority 0 llprio 3
media: Ethernet none (none loopback)
status: active
