Hello! Just got my Pinebook Pro. What a beauty! And I am forced to stay at home because of SARS-COV-II/COVID-19.
This lucky coincidence is dulled by my incapability to install OpenBSD on the Pinebook Pro. I've tried everything I could find, from: https://ftp.openbsd.org/pub/OpenBSD/snapshots/arm64/INSTALL.arm64 "Install on systems without a supported miniroot:" ... to various hints on forums.pine64.org, which mostly relate to the pinebook (w/o "pro"). Initially OpenBSD -current install ran ok until the point where the firmware for the bwfm(4) wifi was not found. I then used the upgrade script that comes with the original OS. Afterwards I only ever got to the boot> prompt where it never finds anything to boot/install from. I have the output from serial saved, see below. Has anyone got a hint for me? Thanks, Marcus $ cu -s 1500000 -l /dev/cuaU0 -d -- boot from sdcard -- Connected to /dev/cuaU0 (speed 1500000) DDR Version 1.20 20190314 In channel 0 CS = 0 MR0=0x98 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 1 CS = 0 MR0=0x98 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x1 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 0 training pass! channel 1 training pass! change freq to 400MHz 0,1 channel 0 CS = 0 MR0=0x98 MR4=0x81 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x81 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 1 CS = 0 MR0=0x98 MR4=0x81 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 M0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x1 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 0 training pass! channel 1 training pass! change freq to 800MHz 1,0 Channel 0: LPDDR4,800MHz Bus Width=32 Col=10 nk=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB Channel 1: LPDDR4,800MHz Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB 256B stride ch 0 ddrconfig = 0x101, ddrsize = 0x2020 ch 1 ddrconfig = 0x101, ddrsize = 0x2020 pmugrf_os_r= 0x3AA1FAA1, stride = 0xD OUT Boot1: 2019-03-14, version: 1.19 CPUId = 0x0 ChipType = 0x10, 250 SdmmcInit=2 0 BootCapSize=100000 UserCapSize=59640MB FwPartOffset=2000 , 100000 mmc0:cmd5,20 mmc0:cmd7,10 mmc0:cmd5,20 mmc0:cmd7,10 mmc0:cmd5,20 mmc0:cmd7,10 SdmmcInit=0 1 StorageInit ok = 355218 SecureMode = 0 SecureInit read PBA: 0x4 SecureInit read PBA: 0x404 SecureInit read PBA: 0x804 SecureInit read PBA: 0xc04 SecureInit read PBA: 0x1004 SecureInit read PBA: 0x1404 SecureInit read PBA: 0x1804 SecureInit read PBA: 0x1c04 SecureInit ret = 0, SecuMode = 0 atags_set_bootdev: ret:(0) GPT 0x3380ec0 signature is wrong recovery gpt... GPT 0x3380ec0 signature is wrong recovery gpt fail! LoadTrust Addr:0x4000 No find bl30.bin No find bl32.bin Load uboot, ReadLba = 2000 Load OK, addr=0x200000, size=0xe5970 RunBL31 0x10000 NOTICE: BL31: v1.3(debug):22b599a NOTICE: BL31: Built : 11:03:32, Jul 10 2019 NOTICE: BL31: Rockchip release version: v1.1 INFO: GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3 INFO: Using opteed sec cpu_context! INFO: boot cpu mask: 0 INFO: plat_rockchip_pmu_init(1181): pd status 3e INFO: BL31: Initializing runtime services WARNING: No OPTEE provideting device without OPTEE initialization. SMC`s destine d for OPTEE will return SMC_UNK ERROR: Error initializing runtime service opteed_fast INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x200000 INFO: SPSR =fdtdec_get_addr_size_fixed: reg: addr=ff770000, size=10000 fdtdec_get_addr_size_fixed: reg: addr=ff320000, size=1000 U-Boot 2017.09-04112-gb8e0774-dirty (Feb 07 2020 - 12:45:13 -0500) Model: Pine64 RK3399 Pinebook Pro PreSerial: 2 DRAM: 3.9 GiB Sysmem: init Relocation Offset: f5be7000, fdt: f3dd2238 I2c0 speed: 400000Hz PMIC: RK808 vdd_center 900000 uV vdd_log init 900000 uV rk_board_init PWM2 pinctrl init fail! rk_board_init: vcc3v0_sdio cannot set regulator value -38 vdd_center 900000 uV DCDC_REG1@ vdd_center: 750000uV <-> 1400000uV, set 900000u V, enabling | suspend -61uV, disabled DCDC_REG4@ vcc_1v8: 1800000uV 00uV, set 1800000uV, enabli ng | suspend 1800000uV, enabling LDO_REG1@ vcc1v8_dvp: 1800000uV <-> 1800000uV, set 1800000u V, enabling | suspend 1800000uV, enabling LDO_REG4@ vcc_sd: 3300000uV <-> 3300000uV, set nd 33000 00uV, enabling LDO_REG5@ vcca3v0_codec: 3000000uV <-> 3000000uV, set 3000000u V, enabling | suspend 3000000uV, enabling LDO_REG7@ vcca1v8_codec: 1800000uV <-> 1800000uV, set 1800000u V, enabling | suspend 18000008@ vcc_3v0: 3000000uV <-> 3000000uV, set 300 0000uV, enabling | suspend 3000000uV, enabling SWITCH_REG2@ vcc3v3_s0: -61uV <-> -61uV, set 0u V, enabling | suspend -61uV, disabled dc-12v@ -38) vcc3v3-sys@ vcc3v3_sys: 3300000uV <-> 3300000uV, set 3300000u V, enabling | suspend -61uV, enabling (ret: -38) vcc-phy-regulator@ vcc_phy: -61uV <-> -61uV, set -61u V, enabling | suspend -61uV, enauV <-> -61uV, set -61uV, enabling | suspend -61uV, enabling vcc5v0-host-en@ vcc5v0_host: 5000000uV <-> 5000000uV, set 5000000u V, enabling | suspend -61uV, enabling (ret: -38) vcc5v0-usb3-host-regulator@vcc5v0_usb3_host: 1uV, enabling | suspend -61 uV, enabling vcc5v0-typec0-en@ vcc5v0_typec0: -61uV <-> -61uV, set -61u V, enabling | suspend -61uV, enabling vcc3v3-pcie-regulator@ vcc3v3_pcie: 3300000uV <-> 3300000uV, set 3300000u V, disabnabling vcc1v8-sdio@ vcc1v8_sdio: 1800000uV <-> 1800000uV, set 1800000u V, enabling | suspend -61uV, enabling (ret: -38) vcc3v0-sdio@ vcc3v0_sdio: 3000000uV <-> 3000000uV, set 3000000u V, enabling | suspend -61uV, 8) vdd_log init 900000 uV vdd_log@ vdd_log: 800000uV <-> 1400000uV, set 900000u V, enabling | suspend -61uV, enabling ; init 900000uV MMC: dwmmc@fe310000: 2, sdhci@fe330000: 0, dwmmc@fe320000: 1 Invalid bus 0 (err=-19) *** Warning - spi_flash_probe_bus_cs() failed, using default environment In: serial Out: serial Err: serial Model: Pine64 RK3399 Pinebook Pro RKPARM: Invalid parameter part table Bootdev(atags): mmc 0 PartType: DOS rockchip_get_boot_mode: Could not found misc partition boot mode: None init_resource_list: failed to get resource part, ret=-1 Can't find file:logo.bmp failed to display uboot logo CLK: (uboot. arml: enter 816000 KHz, init 816000 KHz, kernel 0N/A) CLK: (uboot. armb: enter 816000 KHz, init 816000 KHz, kernel 0N/A) aplll 816000 KHz apllb 816000 KHz dpll 800000 KHz cpll 24000z vpll 24000 KHz aclk_perihp 133333 KHz hclk_perihp 66666 KHz pclk_perihp 33333 KHz aclk_perilp0 266666 KHz hclk_perilp0 88888 KHz pclk_perilp0 44444 KHz hclk_perilp1 100000 KHz pclk_perilp1 50000 KHz Net: No ethernet found. Hit key to stop autoboot('CTRL+C'): 0 do_boot_rockchip: Could not find mmcsda2 part Checking for mmc dev 1... RKPARM: Invalid parameter part table switch to partitions #0, OK mmc1 is current device Scanning mmc 1 for bootable partitions... Scanning mmc 1:1 for extlinux or boot scripts... Found EFI removable media binary efi/boot/bootaa64.efi reading efi/boot/bootaa64.efi 168758 bytes read in 14 ms (11.5 MiB/s) libfdt fdt_check_header(): FDT_ERR_BADMAGIC ## Starting EFI application at 00280000 ... Card did not respond to voltage select! mmc_init: -95, time 50 Scanning disk dw...@fe310000.blk... MMC: block number 0x1 exceeds max(0x0) MMC: block number 0x2080 exceeds max(0x0) rkparm_init_param_from_storage param read fail RKPARM: Invalid parameter part table MMC: block number 0x1 exceeds max(0x0) MMC: blocnning disk sd...@fe330000.blk... Scanning disk dw...@fe320000.blk... Found 3 disks Adding bank: 0x00200000 - 0xf8000000 (size: 0xf7e00000) disks: sd0 sd1 sd2 sd3 sd4 >> OpenBSD/arm64 BOOTAA64 0.20 open(tftp0a:/etc/boot.conf): Operation not permitted boot> set device hd0a boot> ls stat(hd0a:/.): Device not configured -- boot from usb3: Checking for mmc dev 1... Card did not respond to voltage select! mmc_init: -95, time 9 Checking for nvme dev 0... Device 0: unknown device starting USB... Bus usb@fe380000: USB EHCI 1.00 Bus usb@fe3a0000: USB OHCI 1.0 Bus usb@fe3c0000: USB EHCI 1.00 Bus usb@fe3e0000: USB OHCI 1.0 Bus usb@fe800000: device name usb@fe800000 Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 Bus usb@fe900000: device name usb@fe900000 Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 scanning bus usb@fe380000 for devices... 1 USB Device(s) found scanning bus usb@fe3a0000 for devices... 2 USB Device(s) found scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found scanning bus usb@fe3e0000 for devices... 1 USB Device(s) found scanning bus usb@fe800000 for devices... 1 USB Device(s) found scanning bus usb@fe900000 for devices... RKPARM: Invalid parameter part table 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Checking for usb dev 0... Device 0: Vendor: SanDisk Rev: 0001 Prod: Extreme Type: Hard Disk Capacity: 15272.0 MB = 14.9 GB (31277232 x 512) ... is now current device Scanning usb 0 for bScanning usb 0:1 for extlinux or boot scripts... Found EFI removable media binary efi/boot/bootaa64.efi reading efi/boot/bootaa64.efi 168758 bytes read in 69 ms (2.3 MiB/s) libfdt fdt_check_header(): FDT_ERR_BADMAGIC ## Starting EFI application at 00280000 ... Card did not respond to voltage select! mmc_init: -95, time 50 Scanning disk dw...@fe310000.blk... MMC: block number 0x1 exceeds max(0x0) MMC: block number 0x2080 exceeds max(0x0) rkparm_init_param_from_storage param read fail RKPARM: Invalid parameter part table MMC: block number 0x1 exceeds max(0x0) MMC: blocScanning disk sd...@fe330000.blk... Card did not respond to voltage select! mmc_init: -95, time 9 Scanning disk dw...@fe320000.blk... MMC: block number 0x1 exceeds max(0x0) MMC: block number 0x2080 exceeds max(0x0) rkparm_init_param_from_storage param read fail RKPARM: Invalid parameter part table MMC: block number 0x1 exceeds max(0x0) MMC: blockanning disk usb_mass_storage.lun0... Found 4 disks Adding bank: 0x00200000 - 0xf8000000 (size: 0xf7e00000) disks: sd0 sd1 sd2 sd3 sd4 >> OpenBSD/arm64 BOOTAA64 0.20 open(tftp0a:/etc/boot.conf): Operation not permitted boot> alan01...@gmail.com (Alan Corey), 2020.03.18 (Wed) 14:38 (CET): > OK, thanks, I'll just leave room for it on my SSD and try 6.7 when it > comes out. I'm not in any rush for it. > > On 3/18/20, Otto Moerbeek <o...@drijf.net> wrote: > > On Wed, Mar 18, 2020 at 02:08:07PM +0100, Mark Kettenis wrote: > > > >> You'll need -current on this hardware. > > > > To elaborate a bit: several developers have one and good progress has > > been made. You'll need a very recent snap though and I'm not sure if > > the wifi firmware package needed has been updated already. To be able > > to boot from NVMe you'll need an updated u-boot. But e.g. X works > > already. > > > > -Otto > > > > OpenBSD 6.6-current (GENERIC.MP) #29: Tue Mar 17 09:39:57 CET 2020 > > o...@pbp.intra.drijf.net:/usr/src/sys/arch/arm64/compile/GENERIC.MP > > real mem = 4027723776 (3841MB) > > avail mem = 3831341056 (3653MB) > > mainbus0 at root: Pine64 Pinebook Pro > > cpu0 at mainbus0 mpidr 0: ARM Cortex-A53 r0p4 > > cpu0: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache > > cpu0: 512KB 64b/line 16-way L2 cache > > efi0 at mainbus0: UEFI 2.0.5 > > efi0: Das U-boot rev 0x0 > > apm0 at mainbus0 > > psci0 at mainbus0: PSCI 1.0 > > agintc0 at mainbus0 sec shift 3:4 nirq 288 nredist 6 ipi: 0, 1: > > "interrupt-controller" > > agintcmsi0 at agintc0 > > syscon0 at mainbus0: "qos" > > syscon1 at mainbus0: "qos" > > syscon2 at mainbus0: "qos" > > syscon3 at mainbus0: "qos" > > syscon4 at mainbus0: "qos" > > syscon5 at mainbus0: "qos" > > syscon6 at mainbus0: "qos" > > syscon7 at mainbus0: "qos" > > syscon8 at mainbus0: "qos" > > syscon9 at mainbus0: "qos" > > syscon10 at mainbus0: "qos" > > syscon11 at mainbus0: "qos" > > syscon12 at mainbus0: "qos" > > syscon13 at mainbus0: "qos" > > syscon14 at mainbus0: "qos" > > syscon15 at mainbus0: "qos" > > syscon16 at mainbus0: "qos" > > syscon17 at mainbus0: "qos" > > syscon18 at mainbus0: "qos" > > syscon19 at mainbus0: "qos" > > syscon20 at mainbus0: "qos" > > syscon21 at mainbus0: "qos" > > syscon22 at mainbus0: "qos" > > syscon23 at mainbus0: "qos" > > syscon24 at mainbus0: "qos" > > syscon25 at mainbus0: "power-management" > > "power-controller" at syscon25 not configured > > syscon26 at mainbus0: "syscon" > > "io-domains" at syscon26 not configured > > rkclock0 at mainbus0 > > rkclock1 at mainbus0 > > syscon27 at mainbus0: "syscon" > > "io-domains" at syscon27 not configured > > "usb2-phy" at syscon27 not configured > > "usb2-phy" at syscon27 not configured > > rkemmcphy0 at syscon27 > > "pcie-phy" at syscon27 not configured > > rkpinctrl0 at mainbus0: "pinctrl" > > rkgpio0 at rkpinctrl0 > > rkgpio1 at rkpinctrl0 > > rkgpio2 at rkpinctrl0 > > rkgpio3 at rkpinctrl0 > > rkgpio4 at rkpinctrl0 > > pwmreg0 at mainbus0 > > rkdrm0 at mainbus0 > > drm0 at rkdrm0 > > "pmu_a53" at mainbus0 not configured > > "pmu_a72" at mainbus0 not configured > > agtimer0 at mainbus0: tick rate 24000 KHz > > "xin24m" at mainbus0 not configured > > simplebus0 at mainbus0: "amba" > > "dma-controller" at simplebus0 not configured > > "dma-controller" at simplebus0 not configured > > rkpcie0 at mainbus0 > > pci0 at rkpcie0 > > ppb0 at pci0 dev 0 function 0 "Rockchip RK3399 Root Complex" rev 0x00: msi > > pci1 at ppb0 bus 1 > > nvme0 at pci1 dev 0 function 0 vendor "Intel", unknown product 0xf1a8 rev > > 0x03: msix, NVMe 1.3 > > nvme0: INTEL SSDPEKNW512G8, firmware 002C, serial BTNH907209AN512A > > scsibus0 at nvme0: 2 targets, initiator 0 > > sd0 at scsibus0 targ 1 lun 0: <NVMe, INTEL SSDPEKNW51, 002C> > > sd0: 488386MB, 512 bytes/sector, 1000215216 sectors > > dwmmc0 at mainbus0: 50 MHz base clock > > sdmmc0 at dwmmc0: 4-bit, sd high-speed, dma > > dwmmc1 at mainbus0: 50 MHz base clock > > sdmmc1 at dwmmc1: 4-bit, sd high-speed, mmc high-speed, dma > > sdhc0 at mainbus0 > > sdhc0: SDHC 3.0, 18 MHz base clock > > sdmmc2 at sdhc0: 8-bit, sd high-speed, mmc high-speed, dma > > ehci0 at mainbus0 > > usb0 at ehci0: USB revision 2.0 > > uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev > > 2.00/1.00 addr 1 > > ohci0 at mainbus0: version 1.0 > > ehci1 at mainbus0 > > usb1 at ehci1: USB revision 2.0 > > uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev > > 2.00/1.00 addr 1 > > ohci1 at mainbus0: version 1.0 > > rkdwusb0 at mainbus0: "usb" > > xhci0 at rkdwusb0, xHCI 1.10 > > usb2 at xhci0: USB revision 3.0 > > uhub2 at usb2 configuration 1 interface 0 "Generic xHCI root hub" rev > > 3.00/1.00 addr 1 > > rkdwusb1 at mainbus0: "usb" > > xhci1 at rkdwusb1, xHCI 1.10 > > usb3 at xhci1: USB revision 3.0 > > uhub3 at usb3 configuration 1 interface 0 "Generic xHCI root hub" rev > > 3.00/1.00 addr 1 > > "dp" at mainbus0 not configured > > "saradc" at mainbus0 not configured > > rkiic0 at mainbus0 > > iic0 at rkiic0 > > "everest,es8316" at iic0 addr 0x11 not configured > > rkiic1 at mainbus0 > > iic1 at rkiic1 > > com0 at mainbus0: ns16550, no working fifo > > com1 at mainbus0: ns16550, no working fifo > > com1: console > > "spi" at mainbus0 not configured > > "thermal-zones" at mainbus0 not configured > > rktemp0 at mainbus0 > > rkiic2 at mainbus0 > > iic2 at rkiic2 > > rkpmic0 at iic2 addr 0x1b: RK808 > > fanpwr0 at iic2 addr 0x40: SYR827, 1.00 VDC > > fanpwr1 at iic2 addr 0x41: SYR828, 1.00 VDC > > rkiic3 at mainbus0 > > iic3 at rkiic3 > > fusbtc0 at iic3 addr 0x22 > > "cellwise,cw201x" at iic3 addr 0x62 not configured > > rkpwm0 at mainbus0 > > rkpwm1 at mainbus0 > > "video-codec" at mainbus0 not configured > > "iommu" at mainbus0 not configured > > "rga" at mainbus0 not configured > > "efuse" at mainbus0 not configured > > "phy" at mainbus0 not configured > > "phy" at mainbus0 not configured > > "watchdog" at mainbus0 not configured > > "rktimer" at mainbus0 not configured > > "i2s" at mainbus0 not configured > > rkvop0 at mainbus0: RK3399 VOPL > > "iommu" at mainbus0 not configured > > rkvop1 at mainbus0: RK3399 VOPB > > "iommu" at mainbus0 not configured > > "iommu" at mainbus0 not configured > > "iommu" at mainbus0 not configured > > "hdmi-sound" at mainbus0 not configured > > rkanxdp0 at mainbus0: eDP TX > > "gpu" at mainbus0 not configured > > "opp-table0" at mainbus0 not configured > > "opp-table1" at mainbus0 not configured > > "opp-table2" at mainbus0 not configured > > simplepanel0 at mainbus0 > > "leds" at mainbus0 not configured > > "reserved-memory" at mainbus0 not configured > > "gpio-keys" at mainbus0 not configured > > pwmbl0 at mainbus0 > > "sdio-pwrseq" at mainbus0 not configured > > "wireless-wlan" at mainbus0 not configured > > "es8316-sound" at mainbus0 not configured > > "speaker-amplifier" at mainbus0 not configured > > "vcc-sysin" at mainbus0 not configured > > "vcc-12v" at mainbus0 not configured > > "vcc3v3-sys" at mainbus0 not configured > > "vcc5v0-usb-regulator" at mainbus0 not configured > > "vcc-0v9" at mainbus0 not configured > > "vcc1v8-s3" at mainbus0 not configured > > "vcc3v0-sd" at mainbus0 not configured > > "vcc3v3-panel" at mainbus0 not configured > > "vcc3v3-ssd" at mainbus0 not configured > > "vcc5v0-otg" at mainbus0 not configured > > "vbus-5vout" at mainbus0 not configured > > "dc-charger" at mainbus0 not configured > > "usb-charger" at mainbus0 not configured > > "framebuffer" at mainbus0 not configured > > cpu1 at mainbus0 mpidr 1: ARM Cortex-A53 r0p4 > > cpu1: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache > > cpu1: 512KB 64b/line 16-way L2 cache > > cpu2 at mainbus0 mpidr 2: ARM Cortex-A53 r0p4 > > cpu2: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache > > cpu2: 512KB 64b/line 16-way L2 cache > > cpu3 at mainbus0 mpidr 3: ARM Cortex-A53 r0p4 > > cpu3: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache > > cpu3: 512KB 64b/line 16-way L2 cache > > cpu4 at mainbus0 mpidr 100: ARM Cortex-A72 r0p2 > > cpu4: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache > > cpu4: 1024KB 64b/line 16-way L2 cache > > cpu5 at mainbus0 mpidr 101: ARM Cortex-A72 r0p2 > > cpu5: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache > > cpu5: 1024KB 64b/line 16-way L2 cache > > usb4 at ohci0: USB revision 1.0 > > uhub4 at usb4 configuration 1 interface 0 "Generic OHCI root hub" rev > > 1.00/1.00 addr 1 > > usb5 at ohci1: USB revision 1.0 > > uhub5 at usb5 configuration 1 interface 0 "Generic OHCI root hub" rev > > 1.00/1.00 addr 1 > > bwfm0 at sdmmc0 function 1 > > manufacturer 0x02d0, product 0xa9bf at sdmmc0 function 2 not configured > > manufacturer 0x02d0, product 0xa9bf at sdmmc0 function 3 not configured > > scsibus1 at sdmmc2: 2 targets, initiator 0 > > sd1 at scsibus1 targ 1 lun 0: <Sandisk, DA4064, 0000> removable > > sd1: 59640MB, 512 bytes/sector, 122142720 sectors > > uhub6 at uhub1 port 1 configuration 1 interface 0 "Genesys Logic USB2.0 Hub" > > rev 2.00/85.36 addr 2 > > uvideo0 at uhub6 port 2 configuration 1 interface 0 "Sonix Technology Co., > > Ltd. USB Camera" rev 2.00/0.00 addr 3 > > video0 at uvideo0 > > uhidev0 at uhub4 port 1 configuration 1 interface 0 "HAILUCK CO.,LTD USB > > KEYBOARD" rev 1.10/1.00 addr 2 > > uhidev0: iclass 3/1 > > ukbd0 at uhidev0: 8 variable keys, 6 key codes > > wskbd0 at ukbd0 mux 1 > > uhidev1 at uhub4 port 1 configuration 1 interface 1 "HAILUCK CO.,LTD USB > > KEYBOARD" rev 1.10/1.00 addr 2 > > uhidev1: iclass 3/0, 35 report ids > > umt0 at uhidev1: clickpad, 4 contacts > > wsmouse0 at umt0 mux 0 > > vscsi0 at root > > scsibus2 at vscsi0: 256 targets > > softraid0 at root > > scsibus3 at softraid0: 256 targets > > bootfile: sd0a:/bsd > > boot device: sd0 > > root on sd0a (affd0af770a51ab1.a) swap on sd0b dump on sd0b > > rkvop0: using CRTC 0 for RK3399 VOPL > > rkvop1: using CRTC 1 for RK3399 VOPB > > rkdrm0: 1920x1080, 32bpp > > wsdisplay0 at rkdrm0 mux 1 > > wskbd0: connecting to wsdisplay0 > > wsdisplay0: screen 0-5 added (std, vt100 emulation) > > bwfm0: address c0:84:7d:25:a1:f2
