On Sat, 11 Feb 2012 01:08:13 -0600 Robby Workman <[email protected]> wrote:
> On Sun, 01 Jan 2012 03:29:24 -0500 > John O'Donnell <[email protected]> wrote: > > > I upgraded from 3.1.2 to the 3.1.5 packages yesterday. Before > > attempting to compile the guruplug UAP drivers I tried to boot and > > had no luck. Hung at: > > > > > > -- ## Booting kernel from Legacy Image at 00800000 ... > > Image Name: Linux-3.1.5-kirkwood > > Image Type: ARM Linux Kernel Image (uncompressed) > > Data Size: 2090424 Bytes = 2 MiB > > Load Address: 00008000 > > Entry Point: 00008000 > > Verifying Checksum ... OK > > ## Loading init Ramdisk from Legacy Image at 01100000 ... > > Image Name: Slackware ARM Initial RAM disk f > > Image Type: ARM Linux RAMDisk Image (gzip compressed) > > Data Size: 5811263 Bytes = 5.5 MiB > > Load Address: 00000000 > > Entry Point: 00000000 > > Verifying Checksum ... OK > > Loading Kernel Image ... OK > > OK > > > > Starting kernel ... > > > > Uncompressing Linux... done, booting the kernel. > > > > > > I compiled up the modules and my own uImage with the .config that > > comes with the armedslack kernel source and the same thing happens. > > > > I set it back to 3.1.2 and it boots fine. > > > Oh bah, something definitely changed somewhere along the line :/ > > For a new project here, I need a newer kernel than the one in 13.37, > so I decided to use the 3.2.2 kernel from -current. I get the same > problem here (albeit under slightly different circumstances). > > Mine is installed to the NAND, and rootfs is on the mtd, so I don't > need an initrd at all; thus, my env settings are this: > > Marvell>> printenv > arcNumber=2659 > baudrate=115200 > bootargs_console=console=ttyS0,115200 > bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs rootfs=ubifs > bootcmd=setenv bootargs $(bootargs_console) $(bootargs_root); run > bootcmd_nand; run bootcmd_slack bootcmd_nand=nand read 0x800000 > 0x100000 0x400000 bootcmd_slack=bootm 0x800000 > bootdelay=3 > eth1addr=02:50:43:eb:75:43 > ethact=egiga0 > ethaddr=00:50:43:01:5D:EA > fileaddr=800000 > filesize=36D00 > ipaddr=192.168.13.1 > mainlineLinux=yes > nand_erasesize=20000 > nand_oobsize=40 > nand_writesize=800 > serverip=192.168.13.11 > stderr=serial > stdin=serial > stdout=serial > > > When I boot, here's what happens: > > U-Boot 2011.06 (Jul 26 2011 - 12:26:42) > Marvell-GuruPlug > > SoC: Kirkwood 88F6281_A1 > DRAM: 512 MiB > NAND: 512 MiB > In: serial > Out: serial > Err: serial > Net: egiga0, egiga1 > 88E1121 Initialized on egiga0 > 88E1121 Initialized on egiga1 > Hit any key to stop autoboot: 0 > > NAND read: device 0 offset 0x100000, size 0x400000 > 4194304 bytes read: OK > ## Booting kernel from Legacy Image at 00800000 ... > Image Name: Linux-3.2.2-kirkwood > Image Type: ARM Linux Kernel Image (uncompressed) > Data Size: 2082616 Bytes = 2 MiB > Load Address: 00008000 > Entry Point: 00008000 > Verifying Checksum ... OK > Loading Kernel Image ... OK > OK > > Starting kernel ... > > Uncompressing Linux... done, booting the kernel. > > ... nothing ... > > > I can boot the 13.37 kernel and such just fine still, but I don't > have any of the old 3.1.x kernels from -current. I guess I'll have > to compile my own, because I *really* need something newer than > 2.6.38 :/ And just found this: http://www.mail-archive.com/[email protected]/msg986288.html http://lists.denx.de/pipermail/u-boot/2012-February/117020.html So I went here: http://www.cyrius.com/debian/kirkwood/sheevaplug/uboot-upgrade.html and grabbed this: http://people.debian.org/~tbm/u-boot/2011.12-2/guruplug/u-boot.kwb Even so, this still hangs: U-Boot 2011.12 (Jan 08 2012 - 21:46:50) Marvell-GuruPlug SoC: Kirkwood 88F6281_A1 DRAM: 512 MiB WARNING: Caches not enabled NAND: 512 MiB In: serial Out: serial Err: serial Net: egiga0, egiga1 88E1121 Initialized on egiga0 88E1121 Initialized on egiga1 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x400000 4194304 bytes read: OK ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.2.2-kirkwood Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2082616 Bytes = 2 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. ... bah ... _______________________________________________ ARMedslack mailing list [email protected] http://lists.armedslack.org/mailman/listinfo/armedslack
