Have you loaded the zaptel drivers yet? Until you load the wcfxo module you will see nothing in /proc/interrupts.
Cheers, Peter -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of 163 Sent: Friday, 5 August 2005 12:35 PM To: [email protected] Subject: [Asterisk-Users] HELP! X100P IRQ conflict w/ USB PC: HP Vetra VL400 Mainbood: Intel815 BIOS: Phonix 4.0 release 6.0 OS: REDHAT 9.0 I installed the X100P in PCI slot 2 and disable the USB port, serial-port and parallel-port in BIOS. I can't found the X100P card in " cat interrupts" But I can found the card in the "cat ioports" use "lspci" I found the X100Pcard use the interrupts 11 too. Who can help me to solve this problem? ----------------------------------------------- [EMAIL PROTECTED] proc]# cat interrupts CPU0 0: 28561 XT-PIC timer 1: 6 XT-PIC keyboard 2: 0 XT-PIC cascade 5: 2954 XT-PIC eth0 8: 1 XT-PIC rtc 11: 0 XT-PIC usb-uhci 12: 29 XT-PIC PS/2 Mouse 14: 7199 XT-PIC ide0 15: 1 XT-PIC ide1 NMI: 0 ERR: 0 ------------------------------------------------- ------------------------------------------------- [EMAIL PROTECTED] proc]# cat ioports 0000-001f : dma1 0020-003f : pic1 0040-005f : timer 0060-006f : keyboard 0070-007f : rtc 0080-008f : dma page reg 00a0-00bf : pic2 00c0-00df : dma2 00f0-00ff : fpu 0170-0177 : ide1 01f0-01f7 : ide0 0376-0376 : ide1 0378-037a : parport0 037b-037f : parport0 03c0-03df : vga+ 03f6-03f6 : ide0 0cf8-0cff : PCI conf1 1800-180f : Intel Corp. 82801AA IDE 1800-1807 : ide0 1808-180f : ide1 1810-181f : Intel Corp. 82801AA SMBus 1820-183f : Intel Corp. 82801AA USB 1820-183f : usb-uhci 2000-20ff : Tiger Jet Network Inc. Model 300 128k 2400-247f : 3Com Corporation 3c905C-TX/TX-M [Tornado] 2400-247f : 01:04.0 ------------------------------------------------------ ---------------------------------------------------------------------------- ---- [EMAIL PROTECTED] sbin]# ./lspci -vvv 00:00.0 Host bridge: Intel Corp. 82815 815 Chipset Host Bridge and Memory Contr) Subsystem: Intel Corp. 82815 815 Chipset Host Bridge and Memory Controlb Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Ste- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-- Latency: 0 Capabilities: [88] #09 [f104] 00:02.0 VGA compatible controller: Intel Corp. 82815 CGC [Chipset Graphics Cont) Subsystem: Hewlett-Packard Company: Unknown device 1245 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Ste- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbor- Latency: 0 Interrupt: pin A routed to IRQ 10 Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M] Region 1: Memory at ec000000 (32-bit, non-prefetchable) [size=512K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3ho) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:1e.0 PCI bridge: Intel Corp. 82801AA PCI Bridge (rev 02) (prog-if 00 [Normal) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Ste- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 00002000-00002fff Memory behind bridge: ec100000-ec1fffff Prefetchable memory behind bridge: fff00000-000fffff BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- 00:1f.0 ISA bridge: Intel Corp. 82801AA ISA Bridge (LPC) (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Ste- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbor- Latency: 0 00:1f.1 IDE interface: Intel Corp. 82801AA IDE (rev 02) (prog-if 80 [Master]) Subsystem: Intel Corp. 82801AA IDE Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Ste- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbor- Latency: 0 Region 4: I/O ports at 1800 [size=16] 00:1f.2 USB Controller: Intel Corp. 82801AA USB (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corp. 82801AA USB Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Ste- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbor- Latency: 0 Interrupt: pin D routed to IRQ 11 Region 4: I/O ports at 1820 [size=32] 00:1f.3 SMBus: Intel Corp. 82801AA SMBus (rev 02) Subsystem: Intel Corp. 82801AA SMBus Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Ste- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbor- Interrupt: pin B routed to IRQ 9 Region 4: I/O ports at 1810 [size=16] 01:01.0 Communication controller: Tiger Jet Network Inc. Intel 537 Subsystem: Unknown device 8085:0003 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Ste- Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Ste- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbor- Latency: 64 (250ns min, 32000ns max) Interrupt: pin A routed to IRQ 5 Region 0: I/O ports at 2000 [size=256] Region 1: Memory at ec100000 (32-bit, non-prefetchable) [size=4K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA PME(D0+,D1-,D2+,D3h) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 01:04.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78) Subsystem: Hewlett-Packard Company: Unknown device 1246 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Ste- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbor- Latency: 80 (2500ns min, 2500ns max), cache line size 08 Interrupt: pin A routed to IRQ 5 Region 0: I/O ports at 2400 [size=128] Region 1: Memory at ec101000 (32-bit, non-prefetchable) [size=128] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3ho) Status: D0 PME-Enable- DSel=0 DScale=2 PME- ---------------------------------------------------------------------------- --------- _______________________________________________ Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
