Thanks a lot for you help first. I tried to load the drivers, but failed. -------------------------------------------------------------------- [EMAIL PROTECTED] voicepet-single-x100p]# /sbin/modprobe zaptel modprobe: Can't locate module zaptel [EMAIL PROTECTED] voicepet-single-x100p]# pwd /home/shengl/voicepet-single-x100p -------------------------------------------------------------------- > > Have you loaded the zaptel drivers yet? Until you load the wcfxo module you > will see nothing in /proc/interrupts. > > Cheers, > Peter > > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] On Behalf Of 163 > Sent: Friday, 5 August 2005 12:35 PM > To: [email protected] > Subject: [Asterisk-Users] HELP! X100P IRQ conflict w/ USB > > > PC: HP Vetra VL400 > Mainbood: Intel815 > BIOS: Phonix 4.0 release 6.0 > OS: REDHAT 9.0 > I installed the X100P in PCI slot 2 and disable the USB port, serial-port > and parallel-port in BIOS. I can't found the X100P card in " cat interrupts" > But I can found the card in the "cat ioports" use "lspci" I found the > X100Pcard use the interrupts 11 too. Who can help me to solve this problem? > > ----------------------------------------------- > [EMAIL PROTECTED] proc]# cat interrupts > CPU0 > 0: 28561 XT-PIC timer > 1: 6 XT-PIC keyboard > 2: 0 XT-PIC cascade > 5: 2954 XT-PIC eth0 > 8: 1 XT-PIC rtc > 11: 0 XT-PIC usb-uhci > 12: 29 XT-PIC PS/2 Mouse > 14: 7199 XT-PIC ide0 > 15: 1 XT-PIC ide1 > NMI: 0 > ERR: 0 > ------------------------------------------------- > > ------------------------------------------------- > [EMAIL PROTECTED] proc]# cat ioports > 0000-001f : dma1 > 0020-003f : pic1 > 0040-005f : timer > 0060-006f : keyboard > 0070-007f : rtc > 0080-008f : dma page reg > 00a0-00bf : pic2 > 00c0-00df : dma2 > 00f0-00ff : fpu > 0170-0177 : ide1 > 01f0-01f7 : ide0 > 0376-0376 : ide1 > 0378-037a : parport0 > 037b-037f : parport0 > 03c0-03df : vga+ > 03f6-03f6 : ide0 > 0cf8-0cff : PCI conf1 > 1800-180f : Intel Corp. 82801AA IDE > 1800-1807 : ide0 > 1808-180f : ide1 > 1810-181f : Intel Corp. 82801AA SMBus > 1820-183f : Intel Corp. 82801AA USB > 1820-183f : usb-uhci > 2000-20ff : Tiger Jet Network Inc. Model 300 128k > 2400-247f : 3Com Corporation 3c905C-TX/TX-M [Tornado] > 2400-247f : 01:04.0 > ------------------------------------------------------ > > ---------------------------------------------------------------------------- > ---- > [EMAIL PROTECTED] sbin]# ./lspci -vvv > 00:00.0 Host bridge: Intel Corp. 82815 815 Chipset Host Bridge and Memory > Contr) > Subsystem: Intel Corp. 82815 815 Chipset Host Bridge and Memory > Controlb > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Ste- > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- > <TAbort-- > Latency: 0 > Capabilities: [88] #09 [f104] > > 00:02.0 VGA compatible controller: Intel Corp. 82815 CGC [Chipset Graphics > Cont) > Subsystem: Hewlett-Packard Company: Unknown device 1245 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Ste- > Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbor- > Latency: 0 > Interrupt: pin A routed to IRQ 10 > Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M] > Region 1: Memory at ec000000 (32-bit, non-prefetchable) [size=512K] > Capabilities: [dc] Power Management version 2 > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA > PME(D0-,D1-,D2-,D3ho) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 00:1e.0 PCI bridge: Intel Corp. 82801AA PCI Bridge (rev 02) (prog-if 00 > [Normal) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Ste- > Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- > <TAbort-- > Latency: 0 > Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 > I/O behind bridge: 00002000-00002fff > Memory behind bridge: ec100000-ec1fffff > Prefetchable memory behind bridge: fff00000-000fffff > BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- > > 00:1f.0 ISA bridge: Intel Corp. 82801AA ISA Bridge (LPC) (rev 02) > Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- > Ste- > Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbor- > Latency: 0 > > 00:1f.1 IDE interface: Intel Corp. 82801AA IDE (rev 02) (prog-if 80 > [Master]) > Subsystem: Intel Corp. 82801AA IDE > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Ste- > Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbor- > Latency: 0 > Region 4: I/O ports at 1800 [size=16] > > 00:1f.2 USB Controller: Intel Corp. 82801AA USB (rev 02) (prog-if 00 [UHCI]) > Subsystem: Intel Corp. 82801AA USB > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Ste- > Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbor- > Latency: 0 > Interrupt: pin D routed to IRQ 11 > Region 4: I/O ports at 1820 [size=32] > > 00:1f.3 SMBus: Intel Corp. 82801AA SMBus (rev 02) > Subsystem: Intel Corp. 82801AA SMBus > Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- > Ste- > Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbor- > Interrupt: pin B routed to IRQ 9 > Region 4: I/O ports at 1810 [size=16] > > 01:01.0 Communication controller: Tiger Jet Network Inc. Intel 537 > Subsystem: Unknown device 8085:0003 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Ste- > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Ste- > Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbor- > Latency: 64 (250ns min, 32000ns max) > Interrupt: pin A routed to IRQ 5 > Region 0: I/O ports at 2000 [size=256] > Region 1: Memory at ec100000 (32-bit, non-prefetchable) [size=4K] > Capabilities: [40] Power Management version 2 > Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA > PME(D0+,D1-,D2+,D3h) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 01:04.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev > 78) > Subsystem: Hewlett-Packard Company: Unknown device 1246 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- > Ste- > Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbor- > Latency: 80 (2500ns min, 2500ns max), cache line size 08 > Interrupt: pin A routed to IRQ 5 > Region 0: I/O ports at 2400 [size=128] > Region 1: Memory at ec101000 (32-bit, non-prefetchable) [size=128] > Expansion ROM at <unassigned> [disabled] [size=128K] > Capabilities: [dc] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA > PME(D0+,D1+,D2+,D3ho) > Status: D0 PME-Enable- DSel=0 DScale=2 PME- > ---------------------------------------------------------------------------- > --------- > > _______________________________________________ > Asterisk-Users mailing list > [email protected] > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users >
_______________________________________________ Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
