Hello All ,
On Thu, 27 Oct 2005, Mr. James W. Laferriere wrote:
> On Thu, 27 Oct 2005, Phil Pritchard wrote:
> > only new to asterisk, but have had some hardware exp.....
> > stay away from irq9 its tied to irq2 and will always be shared, Paul has
> > the go.. in bios disable serial and or usb (if not using) and make sure irda
> > is not enabled. another one is the lpt port if your not using that, there is
> > another irq you can steel..
> ALL & I mean all serial/parrallel/...'everything I can find'... has
> been
> turned off in the bios . And I have recompiled a kernel with those
> same
> items turned off in it . That d??ned module wants to load at irq 9 no
> matter what I do . Of course there is no way to set irq's to a
> particular pci slot in the bios .
> Does anyone now howto set irq say at the boot: or in modprobe.conf ?
> > dont share interrupts, as a rule(if you can help it)... it usually leads to
> > system instability and usually under load.
> Quite well understand this point . Have heard it on this list many
> times . And am doing my best NOT too .
> > UBCD ...(www.ultimatebootcd.com). has some nice tools that can probe a
> > system
> > to give a second appinion on interrupt conflicts, ram and hard drive
> > errors.....
> > its my best tool for hardware problems..
> IMO , The mirrors have the su??iest download schemes I have seen in
> some time .\IMO
> I have yet to burn that image but as soon as I do I'll boot it on that
> piece of junk I bought for near next to nothing . Which is almost what
> it is worth , Nothing .
> Thank you for your input , Every bit helps . JimL
Finally got that da??ed wcfxo to load on a irq by itself (*). Had to
turn off the last item of the onbord devices the ether & buy an ether
card to get connectivity . But even with the suggestion by 'Paul' to
use a two line cord & finally using a singular irq , The config's I
sent last time have not changed . The x100p/wcfxo combination see the
line ringing (**) . But asterisk does NOT see it on the console nor
does it pick up the line . Quite frustrating when everything should be
ok per every example I've seen & still nothing positive to show for it .
ANY suggestions/questions/... Please pipe up . Tia , JimL
(*)
Oct 28 09:43:47 asterisk-test kernel: Zapata Telephony Interface Registered on
major 196
Oct 28 09:43:47 asterisk-test kernel: PCI: Found IRQ 5 for device 0000:01:01.0
Oct 28 09:43:47 asterisk-test kernel: Registered Span 1 ('WCFXO/0') with 1
channels
Oct 28 09:43:47 asterisk-test kernel: Span ('WCFXO/0') is new master
Oct 28 09:43:47 asterisk-test kernel: New regoffset: 7
Oct 28 09:43:47 asterisk-test kernel: wcfxo: DAA mode is 'FCC'
Oct 28 09:43:47 asterisk-test kernel: Found a Wildcard FXO: Wildcard X101P
Oct 28 09:43:47 asterisk-test kernel: BATTERY!
Oct 28 09:43:47 asterisk-test kernel: Registered tone zone 0 (United States /
North America)
(**)
Oct 28 09:46:35 asterisk-test kernel: wcfxo: RING!
Oct 28 09:46:37 asterisk-test kernel: wcfxo: NO RING!
Oct 28 09:46:41 asterisk-test kernel: wcfxo: RING!
Oct 28 09:46:43 asterisk-test kernel: wcfxo: NO RING!
Oct 28 09:46:47 asterisk-test kernel: wcfxo: RING!
Oct 28 09:46:49 asterisk-test kernel: wcfxo: NO RING!
--
+------------------------------------------------------------------+
| James W. Laferriere | System Techniques | Give me VMS |
| Network Engineer | 3542 Broken Yoke Dr. | Give me Linux |
| [EMAIL PROTECTED] | Billings , MT. 59105 | only on AXP |
+------------------------------------------------------------------+
_______________________________________________
--Bandwidth and Colocation sponsored by Easynews.com --
Asterisk-Users mailing list
[email protected]
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
