Hey, Thanks for the suggestion. I did but couldnt understand any of it. Here is the link if anyone wants to try.
http://pastebin.ca/33394 Iam trying the suggested hardware hdlc patch. Will keep you guys posted. dushyanth > Try PRI debug span 1 and see if that sheds any light on the problem. > > Thanks, > Steve > > > >>Hello, >> >>Iam trying to configure asterisk with a PRI E1 line. I got to a point >>where incoming calls on PRI is landing on asterisk and asterisk >>immediately starts throwing the below errors on the console. The call > > is > >>dropped at this point somehow. >> >>Dec 12 15:02:57 NOTICE[5783]: chan_zap.c:7437 pri_dchannel: PRI got >>event: HDLC Bad FCS (8) on Primary D-channel of span 1 >>Dec 12 15:02:58 NOTICE[5783]: chan_zap.c:7437 pri_dchannel: PRI got >>event: HDLC Bad FCS (8) on Primary D-channel of span 1 >>Dec 12 15:02:59 NOTICE[5783]: chan_zap.c:7437 pri_dchannel: PRI got >>event: HDLC Abort (6) on Primary D-channel of span 1 >>Dec 12 15:03:00 NOTICE[5783]: chan_zap.c:7437 pri_dchannel: PRI got >>event: HDLC Bad FCS (8) on Primary D-channel of span 1 >>Dec 12 15:03:02 NOTICE[5783]: chan_zap.c:7437 pri_dchannel: PRI got >>event: HDLC Bad FCS (8) on Primary D-channel of span 1 >>Dec 12 15:03:03 NOTICE[5783]: chan_zap.c:7437 pri_dchannel: PRI got >>event: HDLC Abort (6) on Primary D-channel of span 1 >>Dec 12 15:03:04 NOTICE[5783]: chan_zap.c:7437 pri_dchannel: PRI got >>event: HDLC Abort (6) on Primary D-channel of span 1 >>Dec 12 15:03:04 NOTICE[5783]: chan_zap.c:7437 pri_dchannel: PRI got >>event: HDLC Abort (6) on Primary D-channel of span 1 >> >>*CLI> show version >>Asterisk CVS-v1-0-11/08/05-01:22:43 built by [EMAIL PROTECTED] on a i686 >>running Linux >> >> >>>>/etc/zaptel.conf >> >>span=1,1,0,cas,ami >>;span=1,0,0,cas,ami ; have tried this too >>bchan=1-15 >>dchan=16 >>bchan=17-31 >> >> >>>>/etc/asterisk/zapata.conf >> >>; T110P - PRI Configuration >>signalling=pri_cpe >>;switchtype=national >>;switchtype=5ess >>switchtype=euroisdn >>callerid=asreceived >>group=1 >>context=di_mainmenu >>channel => 1-15,17-31 >> >> >>>>cat /proc/zaptel/1 >> >>Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0" AMI/ >> >> 1 WCT1/0/1 Clear (In use) >> 2 WCT1/0/2 Clear (In use) >> 3 WCT1/0/3 Clear (In use) >> 4 WCT1/0/4 Clear (In use) >> 5 WCT1/0/5 Clear (In use) >> 6 WCT1/0/6 Clear (In use) >> 7 WCT1/0/7 Clear (In use) >> 8 WCT1/0/8 Clear (In use) >> 9 WCT1/0/9 Clear (In use) >> 10 WCT1/0/10 Clear (In use) >> 11 WCT1/0/11 Clear (In use) >> 12 WCT1/0/12 Clear (In use) >> 13 WCT1/0/13 Clear (In use) >> 14 WCT1/0/14 Clear (In use) >> 15 WCT1/0/15 Clear (In use) >> 16 WCT1/0/16 HDLCFCS (In use) >> 17 WCT1/0/17 Clear (In use) >> 18 WCT1/0/18 Clear (In use) >> 19 WCT1/0/19 Clear (In use) >> 20 WCT1/0/20 Clear (In use) >> 21 WCT1/0/21 Clear (In use) >> 22 WCT1/0/22 Clear (In use) >> 23 WCT1/0/23 Clear (In use) >> 24 WCT1/0/24 Clear (In use) >> 25 WCT1/0/25 Clear (In use) >> 26 WCT1/0/26 Clear (In use) >> 27 WCT1/0/27 Clear (In use) >> 28 WCT1/0/28 Clear (In use) >> 29 WCT1/0/29 Clear (In use) >> 30 WCT1/0/30 Clear (In use) >> 31 WCT1/0/31 Clear (In use) >> >> >>>>/etc/asterisk/extensions.conf >> >>[di_mainmenu] >>exten => s,1,Answer ; Answer the line >>exten => s,2,SetVar(mloop=0) ; main menu loop count >>exten => s,3,SetVar(mloop=$[${mloop} + 1]) ; increment by 1 , first > > run > >>exten => s,4,DigitTimeout,5 ; Set Digit Timeout to 5 seconds >>exten => s,5,ResponseTimeout,8 ; Set Response Timeout to 8 seconds >>exten => s,6,(di_welcome) >>exten => 1,1,Goto(di_sales,s,1) >>exten => 2,1,Goto(di_techsupport,s,1) >>exten => 3,1,Goto(di_hostingsupport,s,1) >>exten => 4,1,Goto(di_billing,s,1) >>exten => 5,1,Directory(default) >>exten => 9,1,Goto(operator,0,1) >>include => internal >> >>Iam based in India and the PRI line is from TATA indicom. The switch > > iam > >>connected to is a Lucent 5ess. I have tried 5ess as the switchtype too >>in zapata.conf and same errors. >> >>I also get the below warning if i remove and put the PRI line into the >>T110p. >> >>Dec 12 14:26:30 WARNING[5783]: No D-channels available! Using Primary >>channel 16 as D-channel anyway! >> >>zttool shows the PRI status as ok and there are no alarms. >> >>Interrupts details are below. X server is not installed and i have >>disabled dma on my disk. >> >>[EMAIL PROTECTED] ~]# cat /proc/interrupts >> CPU0 CPU1 >> 0: 751204 690283 IO-APIC-edge timer >> 1: 9 0 IO-APIC-edge i8042 >> 8: 1 0 IO-APIC-edge rtc >> 9: 0 0 IO-APIC-level acpi >> 14: 6203 1100 IO-APIC-edge ide0 >>169: 0 0 IO-APIC-level uhci_hcd >>177: 682240 672161 IO-APIC-level uhci_hcd, wctdm >>185: 0 0 IO-APIC-level uhci_hcd >>193: 102135 1252274 IO-APIC-level wcte11xp >>201: 1257747 100020 IO-APIC-level wctdm >>217: 94 6793 IO-APIC-level eth0 >>225: 8722 0 IO-APIC-level eth1 >>NMI: 0 0 >>LOC: 1441441 1441440 >>ERR: 0 >>MIS: 0 >> >> >># hdparm -v /dev/hda >> >>/dev/hda: >> multcount = 16 (on) >> IO_support = 0 (default 16-bit) >> unmaskirq = 1 (on) >> using_dma = 1 (on) >> keepsettings = 0 (off) >> readonly = 0 (off) >> readahead = 256 (on) >> geometry = 16383/255/63, sectors = 40020664320, start = 0 >> >>Wat could cause this problem ? >> >>TIA >>dushyanth _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
