On Tue, 10 Jan 2006 [EMAIL PROTECTED] wrote: > Thank you. > I already downloaded and installed it (they are dated 07-01-2006, version > 0.6.3, correct ?)
Yes. > I maked clean, make and make install. > > Nothing changed, dial out perfect, dial in: (capi debug on) > > asteriskge03*CLI> capi info > Contr1: 2 B channels total, 2 B channels free. > asteriskge03*CLI> > asteriskge03*CLI> > -- CONNECT_IND > (PLCI=0x101,DID=104695467,CID=108680550,CIP=0x1,CONTROLLER=0x1) > == BRI1: Interface cleanup PLCI=0x101 > > BRI1 is the name of my interface > > could it be a kernel issue ?? I am using SUSE Linux 10; I don't think so. Please increase the the verbose level to 5 (set verbose 5) in addition to 'capi debug'. Armin > kernel : 2.6.13-15.7-smp > > Andrea > > > > > Armin Schindler > <[EMAIL PROTECTED] > > To > Sent by: Asterisk Users Mailing List - > asterisk-users-bo Non-Commercial Discussion > [EMAIL PROTECTED] <[email protected]> > m.com cc > > Subject > 10/01/2006 18.29 Re: [Asterisk-Users] CHAN_CAPI > problem > > Please respond to > Asterisk Users > Mailing List - > Non-Commercial > Discussion > <[EMAIL PROTECTED] > ists.digium.com> > > > > > > > I suggest you use the newer chan_capi-cm (loadable from sourceforge.net). > > Armin > > On Tue, 10 Jan 2006 [EMAIL PROTECTED] wrote: > > Hi all, > > I installed asterisk stable cvs 1.2 and chan_capi 0.4.0 PRE1, with one > AVM > > Fritz Card ISDN connected to a Telecom NT1 Plus > > > > I configured asterisk via AMP. > > No problem in making calls. > > If I try to ring the ISDN Phone Number, I don't see anything on the > > asterisk Console, > > I I activate the capi debug , I see the ring on the capi channel. > > If the context were wrong , I anyway should see some line about this.... > > > > Why I cannot see anything on asterisk ,nor in the /var/log/asterisk/full > ? > > > > here is my /etc/asterisk/capi.conf > > > > asteriskge03:/etc/asterisk # cat capi.conf > > ; > > ; CAPI config > > ; > > ; > > > > ; general section > > > > [general] > > nationalprefix=0 > > internationalprefix=00 > > rxgain=0.8 > > txgain=0.8 > > ;ulaw=yes ;set this, if you live in u-law world instead of a-law > > > > ; interface sections ... > > > > [BRI1] ;this example interface gets name 'ISDN1' and may be any > > ;name not starting with 'g' or 'contr'. > > ;ntmode=yes ;if isdn card operates in nt mode, set this to yes > > isdnmode=msn ;'MSN' (point-to-multipoint) or 'DID' (direct inward > dial) > > ;when using NT-mode, 'DID' should be set in any case > > incomingmsn=* ;allow incoming calls to this list of MSNs/DIDs, * = any > > ;defaultcid=123 ;set a default caller id to that interface for dial-out, > > ;this caller id will be used when dial option 'd' is > set. > > ;controller=0 ;ISDN4BSD default > > ;controller=7 ;ISDN4BSD USB default > > controller=1 ;capi controller number to use > > group=1 ;dialout group > > ;prefix=0 ;set a prefix to calling number on incoming calls > > softdtmf=on ;enable/disable software dtmf detection, recommended for > > AVM cards > > relaxdtmf=on ;in addition to softdtmf, you can use relaxed dtmf > > detection > > accountcode= ;Asterisk accountcode to use in CDRs > > context=from-pstn ;context for incoming calls > > holdtype=hold ;when Asterisk puts the call on hold, ISDN HOLD will be > > used. If > > ;set to 'local' (default value), no hold is done and > > Asterisk may > > ;play MOH. > > ;immediate=yes ;DID: immediate start of pbx with extension 's' if no > > digits were > > ; received on incoming call (no destination number > > yet) > > ;MSN: start pbx on CONNECT_IND and don't wait for > > SETUP/SENDING-COMPLETE. > > ; info like REDIRECTINGNUMBER may be lost, but this > is > > necessary for > > ; drivers/pbx/telco which does not send SETUP or > > SENDING-COMPLETE. > > ;echosquelch=1 ;_VERY_PRIMITIVE_ echo suppression > > ;echocancel=yes ;EICON DIVA SERVER (CAPI) echo cancelation > > ;(possible values: 'no', 'yes', 'force', 'g164', 'g165') > > echocancelold=yes;use facility selector 6 instead of correct 8 (necessary > > for older eicon drivers) > > ;echotail=64 ;echo cancel tail setting > > ;bridge=yes ;native bridging (CAPI line interconnect) if available > > ;callgroup=1 ;Asterisk call group > > devices=2 ;number of concurrent calls on this controller > > ;(2 makes sense for single BRI, 30 for PRI) > > > > thanks in advance, > > Andrea > > > > Chi ricevesse questa mail per errore e' gentilmente pregato di > cancellarla. > > > > Visitate il sito http://www.frameweb.it > > > > _______________________________________________ > > --Bandwidth and Colocation provided by Easynews.com -- > > > > Asterisk-Users mailing list > > To UNSUBSCRIBE or update options visit: > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > Asterisk-Users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > Asterisk-Users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
