Due to some failed hardware on another platform, I've had to move a T100P card to a different chassis. After this move was completed, I am seeing some strange results on the T100P card that do not display to me any failure mode with which I am familiar. The card comes up, and shows "good" carrier and status, but Asterisk refuses to bring the D-channel up. Calls of course do not complete, inbound or outbound. The configuration on the system is identical to what I had on the same PRI before I disconnected it. The PRI checks out clean when connected to another Asterisk system. So, it must be something with this particular motherboard or hardware configuration, but is there anything I can do to solve the problem?
Searches through the archives and Google do not show anything relevant on this error message that I was able to find.
Hardware Specs: - Intel 440GX+ motherboard - 500mhz PIII processor - 1u case (horizontal PCI card - no, it's not shorting out)
If I run asterisk -vvvvvvvvgcd I get a whole slew of these lines (all identical) in the stderr output:
DEBUG[13326]: File chan_zap.c, Line 6201 (pri_dchannel): Got event No event (0) on D-channel for span 1
From dmesg: _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users
Well, that was interesting. I suppose I won't put "." characters on a line by themselves any more, since that is the SMTP "end of file" character. I've never seen that actually chop up a message, though...
Here is the same transmission content, slightly altered:
Due to some failed hardware on another platform, I've had to move a T100P card to a different chassis. After this move was completed, I am seeing some strange results on the T100P card that do not display to me any failure mode with which I am familiar. The card comes up, and shows "good" carrier and status, but Asterisk refuses to bring the D-channel up. Calls of course do not complete, inbound or outbound. The configuration on the system is identical to what I had on the same PRI before I disconnected it. The PRI checks out clean when connected to another Asterisk system. So, it must be something with this particular motherboard or hardware configuration, but is there anything I can do to solve the problem?
Searches through the archives and Google do not show anything relevant on this error message that I was able to find.
Hardware Specs: - Intel 440GX+ motherboard - 500mhz PIII processor - 1u case (horizontal PCI card - no, it's not shorting out)
If I run asterisk -vvvvvvvvgcd I get a whole slew of these lines (all identical) in the stderr output:
DEBUG[13326]: File chan_zap.c, Line 6201 (pri_dchannel): Got event No event (0) on D-channel for span 1
From dmesg: ... Zapata Telephony Interface Registered on major 196 PCI: Assigned IRQ 5 for device 00:0b.0 Framer: DS21552, Revision: 3 (T1) Found a Wildcard: Digium Wildcard T100P T1/PRI Registered tone zone 0 (United States / North America) Using ESF/B8ZS coding/framing Calling startup (flags is 4099) Using ESF/B8ZS coding/framing Calling startup (flags is 4099) Registered tone zone 0 (United States / North America) ...
[EMAIL PROTECTED] asterisk]# grep -v "#" /etc/zaptel.conf|uniq loadzone = us defaultzone=us span=1,1,0,esf,b8zs bchan=1-23 dchan=24
[EMAIL PROTECTED] asterisk]# grep -v ";" /etc/asterisk/zapata.conf [channels] signalling=pri_cpe switchtype=national pridialplan=unknown group=1 usercallerid=yes echocancel=yes echocancelwhenbridged=yes context=pri-inbound channel => 1-23
[EMAIL PROTECTED] asterisk]# more /proc/interrupts
CPU0 0: 8800665 XT-PIC timer
1: 4944 XT-PIC keyboard
2: 0 XT-PIC cascade
5: 0 XT-PIC t1xxp
8: 1 XT-PIC rtc
10: 226264 XT-PIC usb-uhci, eth0
12: 3230 XT-PIC PS/2 Mouse
14: 81878 XT-PIC ide0
NMI: 0
ERR: 0
[EMAIL PROTECTED] asterisk]# ztcfg -vvvvvv
Zaptel Configuration ======================
SPAN 1: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1)
Channel map:
Channel 01: Individual Clear channel (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves: 02) Channel 03: Individual Clear channel (Default) (Slaves: 03) Channel 04: Individual Clear channel (Default) (Slaves: 04) Channel 05: Individual Clear channel (Default) (Slaves: 05) Channel 06: Individual Clear channel (Default) (Slaves: 06) Channel 07: Individual Clear channel (Default) (Slaves: 07) Channel 08: Individual Clear channel (Default) (Slaves: 08) Channel 09: Individual Clear channel (Default) (Slaves: 09) Channel 10: Individual Clear channel (Default) (Slaves: 10) Channel 11: Individual Clear channel (Default) (Slaves: 11) Channel 12: Individual Clear channel (Default) (Slaves: 12) Channel 13: Individual Clear channel (Default) (Slaves: 13) Channel 14: Individual Clear channel (Default) (Slaves: 14) Channel 15: Individual Clear channel (Default) (Slaves: 15) Channel 16: Individual Clear channel (Default) (Slaves: 16) Channel 17: Individual Clear channel (Default) (Slaves: 17) Channel 18: Individual Clear channel (Default) (Slaves: 18) Channel 19: Individual Clear channel (Default) (Slaves: 19) Channel 20: Individual Clear channel (Default) (Slaves: 20) Channel 21: Individual Clear channel (Default) (Slaves: 21) Channel 22: Individual Clear channel (Default) (Slaves: 22) Channel 23: Individual Clear channel (Default) (Slaves: 23) Channel 24: HDLC with FCS check (Default) (Slaves: 24)
24 channels configured.
[EMAIL PROTECTED] asterisk]#
zttool shows "no alarms" but "internally clocked" despite my configuration to take timing from the external loop. Trying to loop up the T1 from zttool results in the "Looping UP span 1..." message to simply hang on the screen, and I have to kill the process manually.
Suggestions are welcome.
JT _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users
