Thanks a billion. Outbound bluetooth dialling on the lines of Dial(BLT/DevName/8005551212) worked for me.
Still trying out the inbound route. Before I created the [bluetooth] context, it tried to reach the [default] context but then I began by creating a new context [bluetooth] in extensions.conf and got my internal SIP phone to ring when I received a call on my SE T616 cell phone. However, I could not get the inbound line answered and I will continue to work on this over the weekend and report back my progress. On 1/25/06, Joseph Tanner <[EMAIL PROTECTED]> wrote: > Again, my documentation is still sparse. I should have noted that the > phone will recognize asterisk and connect even if the channel in > bluetooth.conf is configured wrong. You'll just get no audio, or > disconnects, or what-not until it's set correctly. So realize that > later on when you're testing. Also the usb dongle must have a CSR > chipset, else it won't work (well, at least probably won't work, I'll > provide instructions on how to tell if it should work or not later). > > Here's the relevant instructions on > http://www.crazygreek.co.uk/content/chan_bluetooth for how to dial > out: Send a call out by using Dial(BLT/DevName/0123456). > > As far as dialing in, there's a special context (I think [bluetooth] > maybe? I'll have to get back to you on that). I know that it should > work fine, because I tried dialing the phone, asterisk picked it up > then immediately disconnected because there was no context for it to > go to (I think it tried to fall back on [default], which I didn't have > configured to accept an incoming call). > > Good luck! > > Joseph Tanner > > On 1/26/06, Nilesh Londhe <[EMAIL PROTECTED]> wrote: > > Thanks a lot. I succeeded in pairing my Sony Ericson T616 using your > > instructions at > > http://www.thetechguide.com/howto/asterisk/chanbluetooth.html without > > any problems. I rebooted and the phone prompted me to connect to > > asterisk. I provided the pin 1234 and voila it connected... > > > > Couple of observations: > > > > I started off with clean slate and booted off from [EMAIL PROTECTED] 2.2 CD. > > skipped the initial yum -u update part to save some time. > > > > When I ran the "sdptool search --bdaddr MACADDRESS 0x111F" command, > > below is what I got: > > > > Class 0x111F > > Searching on MACADDRESS > > Service Name: HF Voice Gateway > > Service RecHandle: 0x10007 > > Service Class ID List: > > "" (0x111f) > > "Generic Audio" (0x1203) > > Protocol Descriptor List: > > "L2CAP" (0x0100) > > "RFCOMM" (0x0003) > > Channel: 6 > > Profile Descriptor List > > "" 0x111e > > Version 0x0100 > > > > Note that in /etc/asterisk/bluetooth.conf, I kept Channel = 3 (did not > > change it to 6) and it paired my tooth in the first attempt after I > > rebooted asterisk box. > > > > Now, I want to get rid of my Doc-N-Talk that I currently connect my > > T616 to and the other end of Doc-N-Talk goes to x100p. > > > > Although I have worked with linux a bit, I am basically an ASTERISK > > NEWBIE so please pardon my ignorane but I don't know what to do > > next...that is.. how to define this bluetooth channel to make and > > receive calls using this setup... > > > > Appreciate your help. > > > > > > On 1/25/06, Joseph Tanner <[EMAIL PROTECTED]> wrote: > > > Please note this is a work in progress: > > > > > > http://www.thetechguide.com/howto/asterisk/chanbluetooth.html > > > > > > Basically the bluetoothfiles.tar.gz has the cvs code with the Makefile > > > that worked for me, plus the edited Makefile in > > > /usr/src/asterisk/channels, and the bluez edits I needed (hcid.conf > > > with the correct profile, the files needed for the pin which is set to > > > 1234, etc.). The guide is supposed to walk a person through the > > > entire process of getting an Asterisk box setup and bluetooth working, > > > but it's grossly incomplete. Maybe it'll help you out. > > > > > > Joseph Tanner > > > > > > On 1/25/06, Nilesh Londhe <[EMAIL PROTECTED]> wrote: > > > > Hi Joseph: > > > > > > > > >>I still couldn't compile the newest cvs version of chan_bluetooth, so > > > > >>I again tried my trick of using the Makefile from an older version > > > > >>(which used .tmp to compile) and it worked! > > > > > > > > Can you please point to the cvs you used, the location and content of > > > > pin files you created and paste a copy of the make file that worked > > > > for you? > > > > > > > > Appreciate you sharing this information. Thanks. > > > > > > > > On 1/20/06, Joseph Tanner <[EMAIL PROTECTED]> wrote: > > > > > Ok, I did get this going (somewhat), and in case someone else has the > > > > > same issues I'll detail what I had to do. > > > > > > > > > > First, I was using the instructions at > > > > > http://mundy.org/blog/index.php?p=79. They stated that [EMAIL > > > > > PROTECTED] > > > > > 2.2 already had all the rpms necessary for bluetooth and that I could > > > > > skip the yum install step. I did, however, run the command anyways > > > > > after a few failed attempts. There's an error in the rpm name, they > > > > > tell you to install bluez-libs, the correct name is bluez-libs-devel > > > > > (at least, that's what I needed to install). > > > > > > > > > > I still couldn't compile the newest cvs version of chan_bluetooth, so > > > > > I again tried my trick of using the Makefile from an older version > > > > > (which used .tmp to compile) and it worked! Once compiled, I > > > > > installed and started up asterisk. I then received a message on my > > > > > phone asking if I wanted to allow asterisk to connect, and then asked > > > > > for a pin. This took a bit of figuring out, but I got passed that. > > > > > In /etc/bluetooth/hcid.conf, there's a line that says "pin_helper > > > > > /usr/bin/bluepin;" (it may have a different path, the important thing > > > > > is the pin_helper part). Now backup the script in question, i.e. in > > > > > my case mv /usr/bin/bluepin /usr/bin/bluepin.bak. Use your editor of > > > > > choice to create a new file with the same name, and in it enter: > > > > > > > > > > > > > > > #!/bin/sh -e > > > > > echo "PIN:1234" > > > > > > > > > > Replace the 1234 with whatever you want your pin to be. I don't know > > > > > if this is necessary, but I also edited /etc/bluetooth/pin to read: > > > > > > > > > > 1234 > > > > > > > > > > Again, 1234 should be whatever you want your pin to be. I then > > > > > stopped asterisk, stopped the bluetooth service, started the bluetooth > > > > > service back up, started asterisk, then when my phone asked for a pin > > > > > I put in 1234, and it worked! > > > > > > > > > > You may also need to make another edit to hcid.conf, under Local > > > > > Device Class change it to read class "0x200404;" or possibly "class > > > > > 0x700408;". This makes your bluetooth dongle look like a headset, and > > > > > not a data device (I experienced some flakiness until I changed this). > > > > > > > > > > Now, I edited /etc/asterisk/bluetooth.conf appropriately (changed the > > > > > channel for the phone to 7, it's a Motorola V551), started it all up, > > > > > made some test calls and...no audio! The cellphone works great > > > > > otherwise. It'll connect, stay connected as long as I want it to, and > > > > > when I hang up the asterisk extension the cellphone will disconnect > > > > > too. Too bad I didn't realize 611 was a free call until after I made > > > > > a lot of test calls (it's a prepaid phone). I did call our home > > > > > number directly to see if maybe I just had a one-way audio problem, > > > > > but nobody could hear a thing on either end. I will continue to > > > > > troubleshoot this before I ask another question about it, but it's not > > > > > looking good. BTW, the usb dongle I'm using is a Linksys USBBT100. > > > > > _______________________________________________ > > > > > --Bandwidth and Colocation provided by Easynews.com -- > > > > > > > > > > Asterisk-Users mailing list > > > > > To UNSUBSCRIBE or update options visit: > > > > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > > > > > > > _______________________________________________ > > > > --Bandwidth and Colocation provided by Easynews.com -- > > > > > > > > Asterisk-Users mailing list > > > > To UNSUBSCRIBE or update options visit: > > > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > > > > > _______________________________________________ > > > --Bandwidth and Colocation provided by Easynews.com -- > > > > > > Asterisk-Users mailing list > > > To UNSUBSCRIBE or update options visit: > > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > > > _______________________________________________ > > --Bandwidth and Colocation provided by Easynews.com -- > > > > Asterisk-Users mailing list > > To UNSUBSCRIBE or update options visit: > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > Asterisk-Users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
