Hi Viktor,
So? You seem to have 5 channels set to fxols mode OK. What exactly that
does, I am not sure. FXO operation is highly telco dependent with E1s. I
believe what is implemented in zaptel is an arrangement to work with
some E1 channel banks.
Do you have an actual question this time?
Steve
Viktor Tatianin wrote:
Hi Steve
I have next config
zttool
Current Alarms: No alarms.
Sync Source: Tormenta 2 (PCI) Quad E1 Card
IRQ Misses: 0
Bipolar Viol: 14
Tx/Rx Levels: 0/ 0
Total/Conf/Act: 31/ 6/ 6
1111111111222222222333
1234567890123456789012345789012
TxA 000000
TxB 111111
TxC 000000
TxD 111111
RxA 111111
RxB 011111
RxC 011111
RxD 111111
ztcfg -vv
Zaptel Configuration
======================
SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
SPAN 2: CAS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
Channel map:
Channel 01: Clear channel (Default) (Slaves: 01)
Channel 02: Clear channel (Default) (Slaves: 02)
Channel 03: Clear channel (Default) (Slaves: 03)
Channel 04: Clear channel (Default) (Slaves: 04)
Channel 05: Clear channel (Default) (Slaves: 05)
Channel 06: Clear channel (Default) (Slaves: 06)
Channel 07: Clear channel (Default) (Slaves: 07)
Channel 08: Clear channel (Default) (Slaves: 08)
Channel 09: Clear channel (Default) (Slaves: 09)
Channel 10: Clear channel (Default) (Slaves: 10)
Channel 11: Clear channel (Default) (Slaves: 11)
Channel 12: Clear channel (Default) (Slaves: 12)
Channel 13: Clear channel (Default) (Slaves: 13)
Channel 14: Clear channel (Default) (Slaves: 14)
Channel 15: Clear channel (Default) (Slaves: 15)
Channel 16: D-channel (Default) (Slaves: 16)
Channel 17: Clear channel (Default) (Slaves: 17)
Channel 18: Clear channel (Default) (Slaves: 18)
Channel 19: Clear channel (Default) (Slaves: 19)
Channel 20: Clear channel (Default) (Slaves: 20)
Channel 21: Clear channel (Default) (Slaves: 21)
Channel 22: Clear channel (Default) (Slaves: 22)
Channel 23: Clear channel (Default) (Slaves: 23)
Channel 24: Clear channel (Default) (Slaves: 24)
Channel 25: Clear channel (Default) (Slaves: 25)
Channel 26: Clear channel (Default) (Slaves: 26)
Channel 27: Clear channel (Default) (Slaves: 27)
Channel 28: Clear channel (Default) (Slaves: 28)
Channel 29: Clear channel (Default) (Slaves: 29)
Channel 30: Clear channel (Default) (Slaves: 30)
Channel 31: Clear channel (Default) (Slaves: 31)
Channel 32: FXO Loopstart (Default) (Slaves: 32)
Channel 33: FXO Loopstart (Default) (Slaves: 33)
Channel 34: FXO Loopstart (Default) (Slaves: 34)
Channel 35: FXO Loopstart (Default) (Slaves: 35)
Channel 36: FXO Loopstart (Default) (Slaves: 36)
Channel 37: FXO Loopstart (Default) (Slaves: 37)
37 channels configured.
this is zaptel.conf
; Zapata telephony interface
;
; Configuration file
[trunkgroups]
[channels]
language=en
context=from-isdn-external
;signalling=fxs_ks
;rxwink=300 ; Atlas seems to use long (250ms) winks
signalling=pri_cpe
switchtype=euroisdn
pridialplan=unknown
prilocaldialplan=unknown
callerid=asreceived
usedistinctiveringdetection=yes
usecallingpres=yes
; Whether or not to do distinctive ring detection on FXO lines
;
;usedistinctiveringdetection=yes
usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
echotraining=400
rxgain=0.0
txgain=0.0
group=0
callgroup=1
pickupgroup=1
immediate=no
;faxdetect=both
faxdetect=incoming
;faxdetect=outgoing
;faxdetect=no
;Include genzaptelconf configs
#include zapata-auto.conf
;Include AMP configs
#include zapata_additional.conf
channel=> 1-15,17-31
signalling=fxo_ks
context=bank
group=1
cas=32-37:1101
channel=> 32-37
This is my zapata.conf
# Global data
span=1,1,0,ccs,hdb3
bchan=1-15,17-31
dchan=16
loadzone = us
defaultzone = us
span=2,1,0,cas,hdb3
fxols=32-37
-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] Behalf Of Steve Underwood
Sent: Tuesday, February 21, 2006 2:59 PM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [Asterisk-Users] Tormenta CAS signaling
Viktor Tatianin wrote:
Hi Steve
I attempt change in zapata.conf
cas=1-15:1101 but use zttool view ABCD bits 1010
Regards,
Viktor
Have you put the E1 in CAS mode with something like:
span=1,1,0,cas,hdb3
Steve
-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] Behalf Of Steve
Underwood
Sent: Friday, February 10, 2006 3:25 PM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [Asterisk-Users] Tormenta CAS signaling
Viktor Tatianin wrote:
Hello
Can anyone know how may change(inverting) cas signaling ABCD bits at the
Tormenta 2 (four E1 ports) cards
My cards send idle code ABCD 0101 but my mux which use as channel bank
wait
ABCD 1001
The idle code is set in zapata.conf. For example:
cas=1-15:1101
Sets CAS mode for channels 1 to 15, with the idle pattern 1101.
Regards,
Steve
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
