Hello, One problem is solved and another appears... :( I cannot receive incoming calls on trixbox. I defined one incoming route (any DID/any CID) and forwading these calls to a SIP extension. With capi and sip debug in "asterisk -r" console i dont detect any incoming activity... In xlog console i have the following debug: 0:1898:127 - SIG-R(034) 08 01 0D 05 A1 04 03 80 90 A3 18 01 81 6C 0B 00 83 39 36 33 30 34 35 37 32 33 70 02 81 30 7D 02 91 81 Q.931 CR0d SETUP Sending complete Bearer Capability 80 90 a3 Channel Id 81 Calling Party Number 00 83 '963045723' Called Party Number 81 '0' HLC 91 81 0:1898:127 - SIG-S 0->6 e:805 0:1898:130 - CREATEID ok: context:1f assigned Id:3 freeIds=ec 0:1898:130 - alloc cr in use =4 0:1898:133 - SIG-X(008) 08 01 8D 45 08 02 80 95 Q.931 CR8d DISC Cause 80 95 'Call rejected' 0:1898:133 - SIG-x(008) 08 01 8D 5A 08 02 80 D8 Q.931 CR8d REL_COM Cause 80 d8 'Incompatible destination' 0:1898:133 - SIG-S 6->0 e:8c5 0:1898:134 - D-X(012) 00 01 14 16 08 01 8D 5A 08 02 80 D8 0:1898:135 - free cr in use =3 0:1898:135 - DELETEID ok: deleted Id:4 freeIds=ec 0:1898:155 - D-R(004) 00 01 01 16
So the problem appears to be "Incompatible destination"... but is problem in asterisk or is before asterisk, on diva card...? Tanks by any possible help! Best regards, PS. 2006/10/29, Pedro Silva <[EMAIL PROTECTED]>:
Finally this works!!! :) Tanks to Alberto and Marco by your help! The problems are: - the cable was connected to the wong card port... :( - the card config needs to be: ETSI; TE; Point-to-Point (I thought that was point-to-multipoint). Best regards, PS. 2006/10/29, Pedro Silva <[EMAIL PROTECTED]>: > Hello again Alberto! > > > Anyway, to get more info, try to open a second shell > > and run /usr/lib/eicon/divas/xlog > > then on the first shell redo the telsampl test, then > > post the output of xlog off the list to my address > > (alberto at msoft-italia.com) > > This is the xlog output: > 4:1736:074 - CREATEID ok: context:1f assigned Id:6 freeIds=eb > 4:1736:074 - alloc cr in use =4 > 4:1736:076 - free cr in use =3 > 4:1736:077 - DELETEID ok: deleted Id:6 freeIds=eb > 4:1736:078 - CREATEID ok: context:1f assigned Id:6 freeIds=eb > 4:1736:078 - alloc cr in use =4 > 4:1736:080 - free cr in use =3 > 4:1736:080 - DELETEID ok: deleted Id:6 freeIds=eb > 4:1736:081 - CREATEID ok: context:1f assigned Id:6 freeIds=eb > 4:1736:081 - alloc cr in use =4 > 4:1736:083 - [1,0] dsp_assign 0016, 0, 2048 > 4:1736:083 - [1,0] CAI[00] 16 00 00 00 00 08 > 4:1736:084 - [1,0] Download 532 requested > 4:1736:084 - MORE > 4:1736:085 - SIG-X(029) 08 01 36 05 A1 04 03 80 90 A3 18 01 83 1E > 02 80 83 70 0A 80 39 36 33 30 34 35 37 32 33 > Q.931 CR36 SETUP > Sending complete > Bearer Capability 80 90 a3 > Channel Id 83 > Progress Indicator 80 83 > Called Party Number 80 '963045723' > 4:1736:085 - SIG-S 0->1 e:885 > 4:1736:087 - ACTIVATION_REQ > 4:1744:147 - L1_DOWN > 4:1744:150 - SIG-EVENT FFFF 08 > > 4:1744:150 - SIG-EVENT FFFF 08 > > 4:1744:150 - EVENT: Call failed in State 'Call initiated' > Link disconnected, Layer-1 error (cable or NT) > 4:1744:150 - SIG-S 1->0 e:ffff > 4:1744:151 - [1,0] dsp_release > 4:1744:155 - free cr in use =3 > 4:1744:156 - DELETEID ok: deleted Id:6 freeIds=eb > > I disconnect the rj45 cable from alcatel pbx and connect that to the > diva card (with alcatel pbx i can make calls normally). The green led > of the diva card is activated when i connect the cable. So i dont > understand why the message " Link disconnected, Layer-1 error (cable > or NT)"... > This debug is th same if the cable is connected to the NT or not. > Any ideas...? Thanks! > PS. >
_______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users