CountryCode: 1 AreaCode: 800 FAXNumber: +3705203230 LongDistancePrefix: 1 InternationalPrefix: 011 DialStringRules: etc/dialrules ServerTracing: 0xFFF SessionTracing: 0xFFF RecvFileMode: 0600 LogFileMode: 0600 DeviceMode: 0600 RingsBeforeAnswer: 1 SpeakerVolume: off GettyArgs: "-h %l dx_%s" LocalIdentifier: "Giedrius Augys" TagLineFont: etc/lutRS18.pcf TagLineFormat: "Nuo %%l|%c|Page %%P of %%T" MaxRecvPages: 200 # # # Modem-related stuff: should reflect modem command interface # and hardware connection/cabling (e.g. flow control). # ModemType: Class1 # use this to supply a hint
# # Enabling this will use the hfaxd-protocol to set Caller*ID # #ModemSetOriginCmd: AT+VSID="%s","%d" # # If "glare" during initialization becomes a problem then take # the modem off-hook during initialization, and then place it # back on-hook when done. # #ModemResetCmds: "ATH1\nAT+VCID=1" # enables CallID display #ModemReadyCmds: ATH0 Class1AdaptRecvCmd: AT+FAR=1 Class1TMConnectDelay: 400 # counteract quick CONNECT response # # If you have trouble with V.17 receiving or sending, # you may want to enable one of these, respectively. # #Class1RMQueryCmd: "!24,48,72,96" # enable this to disable V.17receiving #Class1TMQueryCmd: "!24,48,72,96" # enable this to disable V.17sending # # You'll likely want Caller*ID display (also displays DID) enabled. # ModemResetCmds: AT+VCID=1 # enables CallID display # # The pty does not support changing parity. # PagerTTYParity: none # # If you are "missing" Caller*ID data on some calls (but not all) # and if you do not have adequate glare protection you may want to # not answer based on RINGs, but rather enable the CallIDAnswerLength # for NDID, disable AT+VCID=1 and do this: # #RingsBeforeAnswer: 0 #ModemRingResponse: AT+VRID=1 # Uncomment DATE and TIME if you really want them, but you probably don't. #CallIDPattern: "DATE=" #CallIDPattern: "TIME=" CallIDPattern: "NMBR=" CallIDPattern: "NAME=" CallIDPattern: "ANID=" #CallIDPattern: "USER=" # username provided by call #CallIDPattern: "PASS=" # password provided by call #CallIDPattern: "CDID=" # DID context in call CallIDPattern: "NDID=" #CallIDAnswerLength: 4 2007/10/17, Jonn R Taylor <[EMAIL PROTECTED]>: > > Giedrius Augys wrote: > > Hi, > > I have problems with asterisk and hylafax+ iaxmodem. I can successfully > > send faxes to Panasonic KX-FT932 fax, but with Xerox WorkCentre M20i I > > have problems: No carrier. This is hylafax log, maybe you can suggest > > me where to find ... > > > > Oct 17 07:38:48.22: [22428]: SESSION BEGIN 000000041 180037052390906 > > Oct 17 07:38:48.22: [22428]: HylaFAX (tm) Version 4.4.2 > > Oct 17 07:38:48.22: [22428]: SEND FAX: JOB 27 DEST 37052390906 COMMID > > 000000041 DEVICE '/dev/ttyIAX0' FROM 'root < [EMAIL PROTECTED]>' USER root > > Oct 17 07:38:48.22: [22428]: STATE CHANGE: RUNNING -> SENDING > > Oct 17 07:38:48.22: [22428]: <-- [12:AT+FCLASS=1\r] > > Oct 17 07:38:48.22: [22428]: --> [2:OK] > > Oct 17 07:38:48.22 : [22428]: MODEM set XON/XOFF/FLUSH: input ignored, > > output disabled > > Oct 17 07:38:48.22: [22428]: DIAL 37052390906 > > Oct 17 07:38:48.22: [22428]: <-- [16:ATDT37052390906\r] > > Oct 17 07:39:30.86: [22428]: --> [10:NO CARRIER] > > Oct 17 07:39:30.86: [22428]: SEND FAILED: JOB 27 DEST 37052390906 ERR > > [2] No carrier detected > > Oct 17 07:39:30.86: [22428]: SEND FAILED: JOB 27 DEST 37052390906 ERR > > [333] No carrier detected; too many attempts to dial > > Oct 17 07:39:31.86: [22428]: <-- [5:ATH0\r] > > Oct 17 07:39:31.86: [22428]: --> [2:OK] > > Oct 17 07:39:31.86: [22428]: MODEM set DTR OFF > > Oct 17 07:39:31.86: [22428]: MODEM set baud rate: 0 baud (flow control > > unchanged) > > Oct 17 07:39:31.86: [22428]: STATE CHANGE: SENDING -> MODEMWAIT (timeout > 5) > > Oct 17 07:39:31.86: [22428]: SESSION END > > > > > > -- > > Pagarbiai / Best Regards, > > Giedrius Augys > > > > > > ------------------------------------------------------------------------ > > > > _______________________________________________ > > --Bandwidth and Colocation Provided by http://www.api-digital.com-- > > > > asterisk-users mailing list > > To UNSUBSCRIBE or update options visit: > > http://lists.digium.com/mailman/listinfo/asterisk-users > Please post your iaxmodem config file. > > Jonn > > _______________________________________________ > --Bandwidth and Colocation Provided by http://www.api-digital.com-- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > -- Pagarbiai / Best Regards, Giedrius Augys
_______________________________________________ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
