Thanks for the additional comments, I though the timing was odd as well as I had thought it would be the provider that set the timing but it is currently working here and apparently at other sites.
I'll let everyone know if it turns out to be incorrect somehow. -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Tzafrir Cohen Sent: September 28, 2010 11:06 AM To: [email protected] Subject: Re: [asterisk-users] TELUS British Columbia PRI Settings On Tue, Sep 28, 2010 at 11:23:16AM -0500, [email protected] wrote: > I'd just like to thank everyone that helped me get this running. I thought I had a FAS PRI but it turns out it was NFAS so there was no dchannel on the second PRI. When getting the 2nd PRI changed, I received an email containing the cheat sheet TELUS employees use which I thought I should share, though quite a few settings will be obvious to Asterisk gurus. > > The TELUS cheat sheet > ________________________________________________________ > > Asterisk PRI provisioning > ========================= > > T1 span timing is provisioned in /etc/zaptel.conf or /etc/dahdi/system.conf > ------------------------------------------------------------------------ --- > > For syntax see [system.conf.sample](http://svn.digium.com/svn/dahdi/tools/trunk/system. conf.sample) > > ### Defining a span as esf/b8zs > span=1,0,0,esf,b8zs > > ### Defining a span as sf/ami > span=1,0,0,d4,ami Both have timing=0 . That is: that device sets the timing on the T1 line. Shouldn't it be '1' instead? > > > PRI B/D channels are provisioned in /etc/zaptel.conf or /etc/dahdi/system.conf > ------------------------------------------------------------------------ ------ > > For syntax see [system.conf.sample](http://svn.digium.com/svn/dahdi/tools/trunk/system. conf.sample) > > bchan=1-23 > dchan=24 > > PRI interface options are provisioned in /etc/asterisk/zapata.conf or /etc/asterisk/chan_dahdi.conf > ------------------------------------------------------------------------ --------------------------- > > For syntax see [chan_dahdi.conf.sample](http://svn.digium.com/svn/asterisk/trunk/config s/chan_dahdi.conf.sample) > > [channels] > ;--- PRI interface options > ; Switchtype: Only used for PRI. > ; > ; national: National ISDN 2 (default) > ; dms100: Nortel DMS100 > ; 4ess: AT&T 4ESS > ; 5ess: Lucent 5ESS > ; euroisdn: EuroISDN (common in Europe) > ; ni1: Old National ISDN 1 > ; qsig: Q.SIG > > switchtype=national > context=incoming-from-dahdi ; defined in extensions.conf > signalling=pri_cpe ; should be pri-cpe for customer side > > ### Defining channel groups for selection > > Once you've defined groups in chan_dahdi.conf.sample they can be referenced in extensions.conf > > [channels] > ;--- PRI interface options > . . . > group=1 ; reference for hunting method in extensions.conf > channel=>1-23 ; follows b-channel provisioning Note that anything after that 'channel=>' line has no effect on those channels. > > ### TON / NPI > For syntax see [chan_dahdi.conf.sample](http://svn.digium.com/svn/asterisk/trunk/config s/chan_dahdi.conf.sample) > ; unknown: Unknown > ; private: Private ISDN > ; local: Local ISDN > ; national: National ISDN > ; international: International ISDN > ; dynamic: Dynamically selects the appropriate dialplan > ; redundant: Same as dynamic, except that the underlying number is not > ; changed (not common) > > #### pridialplan > For syntax see [chan_dahdi.conf.sample](http://svn.digium.com/svn/asterisk/trunk/config s/chan_dahdi.conf.sample) > > * "national" : Interpret the digits as a national number. > * "international" : A fully formed E.164 phone number. > > [channels] > . . . > ; PRI Dialplan: The ISDN-level Type Of Number (TON) or numbering plan, used for > ; the dialed number. For most installations, leaving this as 'unknown' (the > ; default) works in the most cases. In some very unusual circumstances, you > ; may need to set this to 'dynamic' or 'redundant'. Note that if you set one > ; of the others, you will be unable to dial another class of numbers. For > ; example, if you set 'national', you will be unable to dial local or > ; international numbers. > pridialplan=unknown ; Asterisk default As of 1.6.0 . On 1.4 the default is 'national'. -- Tzafrir Cohen icq#16849755 jabber:[email protected] +972-50-7952406 mailto:[email protected] http://www.xorcom.com iax:[email protected]/tzafrir -- _____________________________________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs: http://www.asterisk.org/hello asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users -- _____________________________________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs: http://www.asterisk.org/hello asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
