On 14.02.2011 12:17, Sébastien BERGER wrote: > As I know it's only telco who provide the clock. Then you must configure > your span with 1,1,0 > 1 is as TE (terminal equipment) > 0 is as NT (network termination) > > So, configure your span as TE, be sure telco not use crc4. > If already yellow, call your telco and ask him if he provide clock or not.
This is what i am doing now, span in configured to obtain timiing from telco. (span=1,1,0,ccs,hdb3) > > Just to be sure, verify your E1 cable. It's a crossover ? It's out remote location so i dont have direct connection. But thanks for hint, i will also check on that. > > Regards, > Sebastien BERGER > > AB2L > +33 (0)367100783 > [email protected] > > > Le 14/02/2011 11:50, Albert a écrit : >> Hi, >> >> span 1 - e1 line (15 channels) >> span 2 - nothing is connected to 2nd span >> >> below is also status from proc fs >> >> ps. i was also trying with timing provided by card (0) >> span=1,1,0,ccs,hdb3 >> ... >> but result was the same >> >> >> voice:/tmp# cat /proc/dahdi/1 >> Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER) HDB3/CCS YELLOW >> >> 1 TE2/0/1/1 Clear YELLOW(SWEC: MG2) >> 2 TE2/0/1/2 Clear YELLOW(SWEC: MG2) >> 3 TE2/0/1/3 Clear YELLOW(SWEC: MG2) >> 4 TE2/0/1/4 Clear YELLOW(SWEC: MG2) >> 5 TE2/0/1/5 Clear YELLOW(SWEC: MG2) >> 6 TE2/0/1/6 Clear YELLOW(SWEC: MG2) >> 7 TE2/0/1/7 Clear YELLOW(SWEC: MG2) >> 8 TE2/0/1/8 Clear YELLOW(SWEC: MG2) >> 9 TE2/0/1/9 Clear YELLOW(SWEC: MG2) >> 10 TE2/0/1/10 Clear YELLOW(SWEC: MG2) >> 11 TE2/0/1/11 Clear YELLOW(SWEC: MG2) >> 12 TE2/0/1/12 Clear YELLOW(SWEC: MG2) >> 13 TE2/0/1/13 Clear YELLOW(SWEC: MG2) >> 14 TE2/0/1/14 Clear YELLOW(SWEC: MG2) >> 15 TE2/0/1/15 Clear YELLOW(SWEC: MG2) >> 16 TE2/0/1/16 HDLCFCS YELLOW >> 17 TE2/0/1/17 Clear YELLOW(SWEC: MG2) >> 18 TE2/0/1/18 Clear YELLOW(SWEC: MG2) >> 19 TE2/0/1/19 Clear YELLOW(SWEC: MG2) >> 20 TE2/0/1/20 Clear YELLOW(SWEC: MG2) >> 21 TE2/0/1/21 Clear YELLOW(SWEC: MG2) >> 22 TE2/0/1/22 Clear YELLOW(SWEC: MG2) >> 23 TE2/0/1/23 Clear YELLOW(SWEC: MG2) >> 24 TE2/0/1/24 Clear YELLOW(SWEC: MG2) >> 25 TE2/0/1/25 Clear YELLOW(SWEC: MG2) >> 26 TE2/0/1/26 Clear YELLOW(SWEC: MG2) >> 27 TE2/0/1/27 Clear YELLOW(SWEC: MG2) >> 28 TE2/0/1/28 Clear YELLOW(SWEC: MG2) >> 29 TE2/0/1/29 Clear YELLOW(SWEC: MG2) >> 30 TE2/0/1/30 Clear YELLOW(SWEC: MG2) >> 31 TE2/0/1/31 Clear YELLOW(SWEC: MG2) >> >> voice:/tmp# cat /proc/dahdi/2 >> Span 2: TE2/0/2 "T2XXP (PCI) Card 0 Span 2" HDB3/CCS RED >> >> 32 TE2/0/2/1 Clear RED(SWEC: MG2) >> 33 TE2/0/2/2 Clear RED(SWEC: MG2) >> 34 TE2/0/2/3 Clear RED(SWEC: MG2) >> 35 TE2/0/2/4 Clear RED(SWEC: MG2) >> 36 TE2/0/2/5 Clear RED(SWEC: MG2) >> 37 TE2/0/2/6 Clear RED(SWEC: MG2) >> 38 TE2/0/2/7 Clear RED(SWEC: MG2) >> 39 TE2/0/2/8 Clear RED(SWEC: MG2) >> 40 TE2/0/2/9 Clear RED(SWEC: MG2) >> 41 TE2/0/2/10 Clear RED(SWEC: MG2) >> 42 TE2/0/2/11 Clear RED(SWEC: MG2) >> 43 TE2/0/2/12 Clear RED(SWEC: MG2) >> 44 TE2/0/2/13 Clear RED(SWEC: MG2) >> 45 TE2/0/2/14 Clear RED(SWEC: MG2) >> 46 TE2/0/2/15 Clear RED(SWEC: MG2) >> 47 TE2/0/2/16 HDLCFCS RED >> 48 TE2/0/2/17 Clear RED(SWEC: MG2) >> 49 TE2/0/2/18 Clear RED(SWEC: MG2) >> 50 TE2/0/2/19 Clear RED(SWEC: MG2) >> 51 TE2/0/2/20 Clear RED(SWEC: MG2) >> 52 TE2/0/2/21 Clear RED(SWEC: MG2) >> 53 TE2/0/2/22 Clear RED(SWEC: MG2) >> 54 TE2/0/2/23 Clear RED(SWEC: MG2) >> 55 TE2/0/2/24 Clear RED(SWEC: MG2) >> 56 TE2/0/2/25 Clear RED(SWEC: MG2) >> 57 TE2/0/2/26 Clear RED(SWEC: MG2) >> 58 TE2/0/2/27 Clear RED(SWEC: MG2) >> 59 TE2/0/2/28 Clear RED(SWEC: MG2) >> 60 TE2/0/2/29 Clear RED(SWEC: MG2) >> 61 TE2/0/2/30 Clear RED(SWEC: MG2) >> 62 TE2/0/2/31 Clear RED(SWEC: MG2) >> >> >> >> Albert >> >> On 14.02.2011 11:39, Sébastien BERGER wrote: >>> Hello, >>> >>> Can you say us what is connected in which span ? >>> >>> span 1 = >>> span 2 = >>> >>> Yellow would say that the span did not receive external clock >>> >>> Sebastien >>> >>> AB2L >>> +33 (0)367100783 >>> [email protected] >>> >>> >>> Le 14/02/2011 11:34, Albert a écrit : >>>> Hi guys, >>>> >>>> I am getting YELLOW alarm on my span with E1 line. Anyone knows what >>>> could be the problem ? Below is my config and status... >>>> >>>> voice:/etc/dahdi# dahdi_hardware -v >>>> pci:0000:02:08.0 wct4xxp+ d161:1220 Wildcard TE220 (5th Gen) >>>> >>>> >>>> voice:/etc/dahdi# dahdi_scan >>>> [1] >>>> active=yes >>>> alarms=YEL >>>> description=T2XXP (PCI) Card 0 Span 1 >>>> name=TE2/0/1 >>>> manufacturer=Digium >>>> devicetype=Wildcard TE220 (5th Gen) (VPMOCT064) >>>> location=Board ID Switch 0 >>>> basechan=1 >>>> totchans=31 >>>> irq=16 >>>> type=digital-E1 >>>> syncsrc=0 >>>> lbo=0 db (CSU)/0-133 feet (DSX-1) >>>> coding_opts=AMI,HDB3 >>>> framing_opts=CCS,CRC4 >>>> coding=HDB3 >>>> framing=CCS >>>> [2] >>>> <cut> ....</cut> >>>> >>>> voice:/etc/dahdi# cat system.conf >>>> # Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER) >>>> span=1,1,0,ccs,hdb3 >>>> bchan=1-15,17-31 >>>> dchan=16 >>>> echocanceller=mg2,1-15,17-31 >>>> >>>> # Span 2: TE2/0/2 "T2XXP (PCI) Card 0 Span 2" >>>> # span=2,0,0,ccs,hdb3,crc4,yellow >>>> span=2,0,0,ccs,hdb3 >>>> bchan=32-46,48-62 >>>> dchan=47 >>>> echocanceller=mg2,32-46,48-62 >>>> >>>> # Global data >>>> >>>> loadzone = uk >>>> defaultzone = uk >>>> >>>> >>>> >>>> >>>> >>>> ps1. I am using DAHDI drivers in version 2.4.0 >>>> >>>> ps2. in attachment screen from dahdi_tool >>>> >>>> Any help will do. >>>> >>>> Thanks, >>>> Alebert >>>> >>>> >>>> -- >>>> _____________________________________________________________________ >>>> -- Bandwidth and Colocation Provided by http://www.api-digital.com -- >>>> New to Asterisk? Join us for a live introductory webinar every Thurs: >>>> http://www.asterisk.org/hello >>>> >>>> asterisk-users mailing list >>>> To UNSUBSCRIBE or update options visit: >>>> http://lists.digium.com/mailman/listinfo/asterisk-users >>> >>> >>> -- >>> _____________________________________________________________________ >>> -- Bandwidth and Colocation Provided by http://www.api-digital.com -- >>> New to Asterisk? Join us for a live introductory webinar every Thurs: >>> http://www.asterisk.org/hello >>> >>> asterisk-users mailing list >>> To UNSUBSCRIBE or update options visit: >>> http://lists.digium.com/mailman/listinfo/asterisk-users >> >> -- >> _____________________________________________________________________ >> -- Bandwidth and Colocation Provided by http://www.api-digital.com -- >> New to Asterisk? Join us for a live introductory webinar every Thurs: >> http://www.asterisk.org/hello >> >> asterisk-users mailing list >> To UNSUBSCRIBE or update options visit: >> http://lists.digium.com/mailman/listinfo/asterisk-users >> > > > -- > _____________________________________________________________________ > -- Bandwidth and Colocation Provided by http://www.api-digital.com -- > New to Asterisk? Join us for a live introductory webinar every Thurs: > http://www.asterisk.org/hello > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > > -- _____________________________________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs: http://www.asterisk.org/hello asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
