Hi Michael, Thanks a lot for your help. I can see the four files when i untar the iaxComm. How can i get the *CLI prompt? Is it possible to uninstall the asterisk package? If so, how can i uninstall so that i can configure asterisk with iaxComm.
Thanks & Regards, Suresh --- Michael Van Donselaar <[EMAIL PROTECTED]> wrote: > On Mon, 22 Mar 2004 06:31:00 -0800 (PST), suresh > kumar <[EMAIL PROTECTED]> > wrote: > > >Hi, > > > PLEASE STOP YELLING > > >INSTALLED ASTERISK PROPERLY AND WORKS FINE. AFTER I > >MADE A WRONG DECISION TO INSTALL iaxComm in the > >Client, it's created problem. When i type asterisk > -r > >command, Now i got display as > >[EMAIL PROTECTED] asterisk]# asterisk -r > >Asterisk CVS-03/18/04-18:01:45, Copyright (C) > >1999-2004 Digium. > >Written by Mark Spencer <[EMAIL PROTECTED]> > >========================================================================= > >Connected to Asterisk CVS-03/18/04-18:01:45 > currently > >running on edventure17 (pid = 4462) > >edventure17*CLI> > ^^^^^^^^^^^^^^^^ *is* the command prompt > > >WHY I AM NOT GETTING *CLI prompt? "edventure12" i > gave > >when registering the iaxComm. How can i get back > *CLI > >prompt? > > You *do* have a command prompt. > > "Installing" iaxComm did not break anything. When > you untar the tar file, you > get an executable, two text files called QUICKSTART > and README and a 16 bit pcm > file called ringtone.raw. No shared libraries. No > changes to any .conf files > > When run, iaxComm creates a lockfile ~/iaxComm.lock > to prevent two instances > from running at the same time. It also creates a > config file of its own, > ~/.iaxComm. Neither of these files will conflict > with asxterisk in any way. > > > > > > > > > > >I am using an on board sound card. HOW CAN I CHECK > >WHETHER IT'S CONFIGURED OR NOT? > > > > > > > > > >I'm also assuming that you still have the default > >extensions.conf. If > >so, you should be able to type dial 600 > > > > > > > > > >YES ... I didn't change the default > extensions.conf. > >If i type dial 600 in edventure17*CLI prompt, > getting > >display as " No such command 'dial' (type 'help' > for > >help)". > > I think this is a result of asterisk not recognizing > your sound card > > >So i type "reload" in edventure17*CLI prompt and > enter > >the key. Then i type dial 600 , i got > edventure17*CLI > >prompt. > >Is there anything wrong with my configuration? > >If it's wrong, How to fix that? > > > > > >Now what can i do to get back to the asterisk > solution > >part. I am not able to continue ... > >PLease advice me what can i do in this stage. > > > >Thanks & Regards, > >Suresh > > > > > >wrote: > ><snip> > >>I would like to get some help from you. > >>My server ip is 192.168.1.1 and i would like to > >>connect to another ip 192.168.1.2. So how can i > >>specify the ip 192.168.1.2 so that make a call > from > >>192.168.1.1? > > > > > > > > > >>Basic configuration is described in the QUICKSTART > >>that came with the binary. > >>But, since you want to originate calls from the > >>asterisk server, that's a bit different. > > > > > > > > > >>I'm assuming that you have asterisk installed and > >>working with your sound card. > > > > > > > > > >>I'm also assuming that you still have the default > >>extensions.conf. If so, you should be able to > type > >>dial 600 > > > > > > > > > >YES ... I didn't change the default > extensions.conf. > >If i type dial 600 in edventure17*CLI prompt, > getting > >display as " No such command 'dial' (type 'help' > for > >help)". > >So i type "reload" in edventure17*CLI prompt and > enter > >the key. Then i type dial 600 , i got > edventure17*CLI > >prompt. > >If it's wrong, How to fix that? > > > > > > > > > >>at the CLI prompt and get the echo test. If not, > >>you'll have to get that fixed before going > further. > > > > > > > > > >>If you can dial extensions from the console OK, > then > >>just > > > > > > > > > >>1. Make and iax.conf entry for an extension > > > > > > > > > >>[101] > >>type=friend > >>host=dynamic > >>secret=foo > >>context=default > >>callerid="Remote PC" <101> > >>diasallow=all > >>allow=gsm > > > > > > > > > >>2. Make an extensions.conf entry for that > extension > >>in the default context > > > > > > > > > >>exten => 101,1,Dial(IAX2/101) > > > > > > > > > >>3. Configure iaxComm on the other machine to use > the > === message truncated === __________________________________ Do you Yahoo!? Yahoo! Finance Tax Center - File online. File on time. http://taxes.yahoo.com/filing.html _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
