[Asterisk-Users] spandsp/rxfax terminates asterisk

[Martin Christian Koch]

Initial handshake sounds fine, but asterisks dies before receive of the fax. Here is the log :   Changed from phase 0 to 1 Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Start receiving document Changed from phase 1 to 4 Sending ident >>> CSI: 40 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 DIS: Preferred octets: 256 Can receive fax Supported data signalling rates: V.27ter and V.29 R8x7.7lines/mm and/or 200x200pels/25.4mm OK 2D coding OK Scan line length: 215mm Recording length: A4 (297mm) Receiver's minimum scan line time: 0ms at 3.85 l/mm: T7.7 = T3.85 R8x15.4lines/mm OK Minimum scan line time for higher resolutions: T15.4 = T7.7 >>> DIS: 80 00 ce f0 80 80 01 HDLC underflow in state 9 Changed from phase 4 to 3 Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down T4 timeout in state 9 Changed from phase 3 to 4 Sending ident >>> CSI: 40 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 DIS: Preferred octets: 256 Can receive fax Supported data signalling rates: V.27ter and V.29 R8x7.7lines/mm and/or 200x200pels/25.4mm OK 2D coding OK Scan line length: 215mm Recording length: A4 (297mm) Receiver's minimum scan line time: 0ms at 3.85 l/mm: T7.7 = T3.85 R8x15.4lines/mm OK Minimum scan line time for higher resolutions: T15.4 = T7.7 >>> DIS: 80 00 ce f0 80 80 01 T2 timeout Start receiving document Sending ident >>> CSI: 40 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 DIS: Preferred octets: 256 Can receive fax Supported data signalling rates: V.27ter and V.29 R8x7.7lines/mm and/or 200x200pels/25.4mm OK 2D coding OK Scan line length: 215mm Recording length: A4 (297mm) Receiver's minimum scan line time: 0ms at 3.85 l/mm: T7.7 = T3.85 R8x15.4lines/mm OK Minimum scan line time for higher resolutions: T15.4 = T7.7 >>> DIS: 80 00 ce f0 80 80 01 HDLC underflow in state 9 Changed from phase 4 to 3 Slow carrier up <<< TSI: 43 30 36 37 37 36 31 36 35 20 35 34 2b 20 20 20 20 20 20 20 20 TSI without final frame tag Remote fax gave TSI as: "+45 56167760" <<< DCS: 83 00 46 20 DCS with final frame tag In state 9 DCS: Can receive fax Selected data signalling rate: V.29, 9600bps R8x7.7lines/mm and/or 200x200pels/25.4mm OK Scan line length: 215mm Recording length: A4 (297mm) Minimum scan line time: 10ms Get at 9600 Changed from phase 3 to 5 Fast carrier up Fast carrier down Fast carrier up Coarse carrier frequency 1700.00 (64) Training error 29.095569 Training succeeded (constellation mismatch 25.504344) Fast carrier trained Fast carrier down Changed from phase 5 to 4 Start rx document - compression 1 Start rx page asterisk in realloc(): warning: junk pointer, too high to make sense Oh dear! >>> CFR: 84 HDLC underflow in state 5 Post trainability Changed from phase 4 to 5 Fast carrier up Coarse carrier frequency 1700.04 (64) Training error 26.487284 Training succeeded (constellation mismatch 27.123313) Fast carrier trained Segmentation fault (core dumped)   Anyone ?   Thanks, Martin Min mail er beskyttet af SPAMfighter 3174 spam mails er blokeret indtil videre. Hent gratis SPAMfighter i dag!