Scott Thanks for that , being new to this i did not really know what to ask / search for . I have now asked my telco and am waiting for a reply.
Thanks again Simon -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Scott Stingel Sent: 04 June 2004 16:35 To: [EMAIL PROTECTED] Subject: RE: [Asterisk-Users] TE410P Q.931 Hi Simon- Just to speed things along, have you see the earlier post regarding Marconi by Darren Storer on this topic? Here it is: "Are you sure that NTL have provided you with a true Q.931 EuroISDN PRI circuit? If the circuit was supplied some time ago for use with existing equipment it may not be fully EuroISDN compliant. When connecting to Telcos that use Marconi (GPT) System X switches you must make sure that the circuit is using ISDN 110 and not ISDN 85. ISDN 85 is an older implementation of Q.931 in the UK and it does not work with Asterisk E100P or TE410P in my experience. When checking with NTL ask if your circuit is ISDN 110 or Q.931e or ETSI; these are the three names that are commonly used by UK carriers for full spec. EuroISDN PRI. " Regards Scott Stingel (who has also had this problem in the UK) Scott M. Stingel President, Emerging Voice Technology, Inc. Palo Alto California & London England www.evtmedia.com -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Simon Sent: Friday, June 04, 2004 7:46 AM To: [EMAIL PROTECTED] Subject: RE: [Asterisk-Users] TE410P Q.931 Darren Thanks for the info , i have made the changes and my telco says he is seeing BUFFER CONTENSIONS on one of the two circuit's ( cct ) . cct 1 is performing correctly cct 2 is not. My telco is providing me with plain Q.931 not Q.931e ( euro ) he has mentioned that my sync settings may not be correct. Being very new to * i am struggling with this now. The telco is providing the sync for me and i am connected to a Marconi System X with a time slot of 16. Is this enough info to get some HELP ???? -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Storer, Darren Sent: 03 June 2004 16:32 To: [EMAIL PROTECTED] Subject: RE: [Asterisk-Users] TE410P Q.931 Hi Simon, the following changes are important: /etc/asterisk/zapata.conf switchtype=euroisdn /* (uncomment this line) pridialplan=local and /etc/zaptel.conf span=1,1,0,ccs,hdb3,crc4 span=2,2,0,ccs,hdb3,crc4 span=3,3,0,ccs,hdb3,crc4 span=4,4,0,ccs,hdb3,crc4 (The lines above assume that all your PRIs will come from a Telco's switch) After you make the changes don't forget to 'init 6' the box. HTH Darren -- Comgate Telco>Internet<Broadcast -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Simon Sent: 03 June 2004 15:43 To: [EMAIL PROTECTED] Subject: RE: [Asterisk-Users] TE410P Q.931 Got this in /etc/asterisk/zapata.conf [channels] context=default signalling=pri_cpe ;switchtype=euroisdn rxwink=300 ; Atlas seems to use long (250ms) winks usecallerid=yes hidecallerid=no callwaiting=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes cancallforward=yes echocancel=yes rxgain=0.0 txgain=0.0 immediate=no musiconhold=default pridialplan=international ; Channels inherit configuration above them ; Span 1 group=1 channel => 1-15 channel => 17-31 signalling=pri_cpe ;switchtype=euroisdn group=2 channel => 32-46 channel => 48-62 signalling=pri_cpe ;switchtype=euroisdn group=3 channel => 63-77 channel => 79-93 signalling=pri_cpe ;switchtype=euroisdn group=4 channel => 94-108 channel => 110-124 and this in etc/zaptel.conf span=1,0,0,ccs,hdb3,crc4 span=2,0,0,ccs,hdb3,crc4 span=3,0,0,ccs,hdb3,crc4 span=4,0,0,ccs,hdb3,crc4 bchan=1-15 bchan=17-31 bchan=32-46 bchan=48-62 bchan=63-77 bchan=79-93 bchan=94-108 bchan=110-124 dchan=16 dchan=47 dchan=78 dchan=109 loadzone = uk defaultzone=uk would this look right ? using zttool i am seeing span 1 OK span 2 YELLOW only got 1 & 2 plugged in Simon -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Apollon Koutlides Sent: 03 June 2004 14:17 To: [EMAIL PROTECTED] Subject: Re: [Asterisk-Users] TE410P Q.931 Simon wrote: >Can anyone help i have * running on debian with a te410p , my telco >tells me >i need it to run in Q.931 anyone know how to make this happen ? > > That's the Layer 2 protocol, PRI signalling. You would obviously do CPE signalling (insert a line signalling=pri_cpe in /etc/asterisk/zaptel.conf) - first you need to get Layer 1 up, of course, and define which channel to be used for signalling in /etc/zapata.conf ( dchan=XX ). Apollon Koutildes _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
