On Sat, 4 Dec 2004 21:18:50 -0600, Rich Adamson [email protected] wrote: > Help me understand what you mean by "neither is providing clock". > > By definition, every single T1 provides clocking within the transmit > side of a T1. Its embedded in the data stream and you can't turn it off. > > Are you talking about clock "sync"?
First, In reply to Lyle, framing/line coding match, and the span 5 is in the dmesg, but the wct1xxp doesn't spit out "SPAN x" and it's mixed in: Found a Wildcard: Digium Wildcard T100P T1/PRI ...Using ESF/B8ZS coding/framing You're absolutely right, so I must be thinking of clock sync, and I'm not clear on recall what I saw from the channel bank. From the T100P though I am sure I saw zero hertz rx. I'll verify again Monday. Anyway, I'll be wrangling Digium again Monday (support was unresponsive Friday). Regardless of other issues, I expect it should be clearing alarms when I stick a loopback plug in. ztcfg (snipped a bit): pbx:~# ztcfg -vv Zaptel Configuration ====================== SPAN 1: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 2: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 3: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 4: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 5: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) Channel map: (snipped out 24,48,72 = D, 1-23,25-47,49-71, 73-94 = B) Channel 95: Individual Clear channel (Default) (Slaves: 95) Channel 96: D-channel (Default) (Slaves: 96) Channel 97: FXO Kewlstart (Default) (Slaves: 97) Channel 98: FXO Kewlstart (Default) (Slaves: 98) Channel 99: FXO Kewlstart (Default) (Slaves: 99) Channel 100: FXO Kewlstart (Default) (Slaves: 100) Channel 101: FXO Kewlstart (Default) (Slaves: 101) Channel 102: FXO Kewlstart (Default) (Slaves: 102) Channel 103: FXO Kewlstart (Default) (Slaves: 103) Channel 104: FXO Kewlstart (Default) (Slaves: 104) Channel 105: FXO Kewlstart (Default) (Slaves: 105) Channel 106: FXO Kewlstart (Default) (Slaves: 106) Channel 107: FXO Kewlstart (Default) (Slaves: 107) Channel 108: FXO Kewlstart (Default) (Slaves: 108) 108 channels configured. zttool (sucky paste): x OK TE410P (PCI) Card 0 Span 1 a x x OK TE410P (PCI) Card 0 Span 2 # x x OK TE410P (PCI) Card 0 Span 3 a x x OK TE410P (PCI) Card 0 Span 4 a x x RED Digium Wildcard T100P T1/PRI Card 0 a x x x Current Alarms: Red Alarm x x x x Sync Source: Internally clocked x a x x x IRQ Misses: 0 x a x x x Bipolar Viol: 0 x a x x x Tx/Rx Levels: 0/ 0 x a x x x Total/Conf/Act: 24/ 12/ 0 x a x x x 111111111122222 lqqqqqqk x a x x x 123456789012345678901234 x Back x x a x x x TxA 000000000000 mqqqqqqj x a x x x TxB 111111111111 x a x x x TxC 000000000000 x # x x x TxD 111111111111 x x x x lqqqqqqk x x x x RxA 000000000000 x Loop x x x x x RxB 000000000000 mqqqqqqj x x x x RxC 000000000000 x x x x RxD 000000000000 x _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users