Scott Stingel wrote:
Sid-
Try connecting one port to another. Note that one of the ports must be set up as "cpe" and the other as "net" in zapata.conf when you loop them together like this.
A suitable crossover cable for testing can be constructed by cutting up a CAT 5 cable, and connecting:
Pin 1 <--> Pin 4 on the other end
Pin 2 <--> Pin 5
Pin 4 <--> Pin 1
Pin 5 <--> Pin 2
You should get green's on both the connected channels if your zaptel and zapata configurations are ok, and if you've run both modprobe and ztcfg as documented.
Good luck Scott Stingel President EVT, Inc.
www.evtmedia.com
Sid wrote:
Hi list,
We have been trying to configure a Quad Span T1 card in a system running RH9. We have followed the instructions in the Wiki and searched the mailing lists, but so far havent got any success. Cable is connected to the first span, and module is loaded. Without loading the module the LED glows in red colour, but the moment we load module, it goes off. (No red or green) .
We ran zttool and tried to run a loop test, but zttool simply hung with the message 'Looping UP Span 1...'. We had to terminate zttool with 'kill'. Here is the output of the lsmod command. Can someone shed some light on this?
Thanks,
-Sid
Module Size Used by Not tainted
wcusb 20128 0 (unused)
wct4xxp 54272 0 (unused)
zaptel 182432 0 [wcusb wct4xxp]
tail -f /var/log/messages
Jan 6 14:54:32 localhost kernel: TE410P: Launching card: 0
Jan 6 14:54:32 localhost kernel: TE410P: Setting up global serial parameters
Jan 6 14:54:32 localhost kernel: Found a Wildcard: Wildcard TE410P-Xilinx
Jan 6 14:54:32 localhost kernel: usb.c: registered new driver wcusb
Jan 6 14:54:32 localhost kernel: Wildcard USB FXS Interface driver registered
Jan 6 14:54:33 localhost kernel: Registered tone zone 0 (United States / North America)
Jan 6 14:54:33 localhost kernel: TE410P: Span 1 configured for ESF/B8ZS
Jan 6 14:54:33 localhost zaptel: Running ztcfg: succeeded
Jan 6 14:55:07 localhost kernel: TE410P: Span 1 configured for ESF/B8ZS
Jan 6 14:55:07 localhost kernel: Registered tone zone 0 (United States / North America)
------------------------------------------------------------------------
Do you Yahoo!?
Yahoo! Mail <http://us.rd.yahoo.com/mail_us/taglines/virus/*http://promotions.yahoo.com/new_mail/static/protection.html> - Helps protect you from nasty viruses.
------------------------------------------------------------------------
_______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Try this, Start the linux box unload zaptel driver by running modprobe -r wct4xxp and modprobe -r zaptel at this point you should see running red led (1 at the time) on all 4 ports
Config your zaptel.conf with appropriate span ( say 2) the ex below is for EUROISDN
span=1,1,0,ccs,hdb3
bchan=1-15,17-31
dchan=16
span=2,1,0,ccs,hdb3 bchan=32-46,48-62 dchan=47 --- Now reload the driver by modprobe wct4xxp ( no need to run modprobe zaptel) and run ztcfg -vvvv and check channels numbering and status
you should see red blinking light on span 1, and 2
now connect a cross cable like recommanded by Scott Stingle start asterisk with the appropriate zapata.conf you shouls see green llight if your config is correct....
Guck Jack
_______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
