Anton Krall wrote:
Zttool shows nothing inside thebox.
I have had similar problems with a TDM400 and CERTAIN Motherboards which are
PCI 2.2 but the TDM400 is not seen, in my case, AT ALL
The one I have reports it as an E/F but the silk-screen clearly says H, Digium contends
there is no problem with the card, the reporting of different version numbers is a
"known bug" but doesn't
prevent the card from working, and because I can place it in another machine
and get it working, they refuse to acknowledge there is any defect in the board.
Perhaps a different motherboard? That is Digium's answer.
Just keep going through hardware that otherwise meets published specs
until you find one that works.
I have to conclude that, due to Digiums refusal to acknowledge there are
problems with the design, ( and there are more I won't bore you with ) and no
willingness to address the issues that have been raised on this list time and
time again, that the TDM400
should be considered a "card of last resort" when absolutely nothing else will
work.
Seems their IAXy falls into that same classification.
Can't say about their T1/E1 cards
JMO
John Novack
I tried removing the x100 cards, moving the tdm card around, disabled all
usb and unnecessary stuff still, kudzu when booting up shows the card and
the card shows up on /etc/sysconfig/hwconf but I wonder why it shows 2 of
these and I only have 1 tdm400p card with 1 module
class: MODEM
bus: PCI
detached: 1
driver: hisax
desc: "Tiger Jet Network Inc.|Intel 537"
vendorId: e159
deviceId: 0001
subVendorId: 8086
subDeviceId: 0003
pciType: 1
-
class: MODEM
bus: PCI
detached: 1
driver: hisax
desc: "Tiger Jet Network Inc.|Intel 537"
vendorId: e159
deviceId: 0001
subVendorId: 8086
subDeviceId: 0003
pciType: 1
Still, interrupts doesn't show the card
[EMAIL PROTECTED] root]# cat /proc/interrupts
CPU0
0: 3994353 XT-PIC timer
1: 2 XT-PIC keyboard
2: 0 XT-PIC cascade
8: 1 XT-PIC rtc
10: 95510 XT-PIC eth0
14: 129871 XT-PIC ide0
NMI: 0
ERR: 0
And when trying to load the drvier
[EMAIL PROTECTED] root]# modprobe zaptel
[EMAIL PROTECTED] root]# modprobe wctdm
/lib/modules/2.4.20-8/misc/wctdm.o: init_module: No such device
Hint: insmod errors can be caused by incorrect module parameters, including
invalid IO or IRQ parameters.
You may find more information in syslog or the output from dmesg
/lib/modules/2.4.20-8/misc/wctdm.o: insmod
/lib/modules/2.4.20-8/misc/wctdm.o failed
/lib/modules/2.4.20-8/misc/wctdm.o: insmod wctdm failed
You have new mail in /var/spool/mail/root
I tried using diff. modules with no luck.,..... Could be the mobo itself?
|-----Original Message-----
|From: [EMAIL PROTECTED]
|[mailto:[EMAIL PROTECTED] On Behalf Of
|Rich Adamson
|Sent: Viernes, 29 de Abril de 2005 08:59 a.m.
|To: Asterisk Users Mailing List - Non-Commercial Discussion
|Subject: Re: [Asterisk-Users] Problems with TDM400P card
|
|> I have a problem getting a TDM400P card to go.
|>
|> It has 4 FXS ports (green modules) and I get this error:
|>
|> [EMAIL PROTECTED] root]# ztcfg -vvvvv
|>
|> Zaptel Configuration
|> ======================
|>
|>
|> Channel map:
|>
|> Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS
|> Kewlstart (Default) (Slaves: 02) Channel 03: FXO Kewlstart (Default)
|> (Slaves: 03) Channel 04: FXO Kewlstart (Default) (Slaves:
|04) Channel
|> 05: FXO Kewlstart (Default) (Slaves: 05) Channel 06: FXO Kewlstart
|> (Default) (Slaves: 06)
|>
|> 6 channels configured.
|>
|> ZT_CHANCONFIG failed on channel 3: Invalid argument (22) Did you
|> forget that FXS interfaces are configured with FXO
|signalling and that
|> FXO interfaces use FXS signalling?
|>
|> My zaptel.conf reads:
|>
|> [EMAIL PROTECTED] root]# more /etc/zaptel.conf
|> fxsks=1
|> fxsks=2
|> fxoks=3-6
|> loadzone=us
|> defaultzone=us
|>
|> And my rc.local loads:
|>
|> /sbin/modprobe zaptel
|> /sbin/modprobe wcfxo
|> /sbin/modprobe wctdm
|>
|> The 2 100p cards load perfectly but the TDM is not.
|>
|> Any ideas?
|
|What does zttool indicate?
|
|Have you tried moving the cards around in different slots?
|
|Any shared interrupt issues?
|
|Try loading wctdm before wcfxo.
|
|Try removing the x100p's and loading the TDM card only. Any issues?
_______________________________________________
Asterisk-Users mailing list
[email protected]
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
