Some more info in case anyone else hits this. "Unable , to create channel of type 'Zap' (cause 66 - Channel not implemented)"
I hit this error again setting up another system. So, not only does it appear if you have more daughter boards than you have configured in zaptel.conf; you will also get it if you define a channel in zapata.conf which refers to a daughter board which is not fitted :-) Most of the search engine results for this error seem to suggest that a recompilation of the code is needed. Obviously for Astlinux this is not genrerally the case. Mart Martin Rogers wrote: > Hi > > I have resolved this issue now, and thought I would share it in case > anyone hits this. > > After the upgrade all the original files were restored to the keydisk > except for the rc.conf and the zaptel.conf which I created by hand. > > When I configured the latter I setup the file as : > > fxsks=3 > fxsks=4 > loadzone=uk > defaultzone=uk > > which ztcfg seemed quite happy about. However what I had forgotten was I > have an FXS module in port 1 which I no longer use (I use just sip > extensions). I added configuration for this module as follows : > > fxoks=1 > fxsks=3 > fxsks=4 > loadzone=uk > defaultzone=uk > > and PSTN is all up and running again. > > The bottom line is that it seems you need zaptel.conf entries for every > module on the card regardless of whether or not you are using it. > > regards > Mart > > Martin Rogers wrote: >> Hi >> >> I have just upgraded a Wyse Winterm box which was running an old >> Astlinux (Asterisk v1.2) to 0.6.1-via. >> >> The box is connected to two PSTN lines via a TDM400 card and has worked >> fine. >> >> I backed up all the config from my key disk and did a physdiskwrite of >> the new image onto the CF. I then scratched the keydisk and ran keygen. >> Finally I copied over my old config. >> >> All went well except that I have no PSTN access. >> >> ztcfg and zttools report back favorably and I have two leds on the back >> of the card. My original dialplan is in place and works fine for my >> SIP-SIP calls, but if I try to call out on a PSTN number I get : >> >> "dial_exec_full: Unable to create channel of type 'Zap' (cause 66 - >> Channel not implemented) " >> >> I would be grateful for any comments. >> >> Thanks >> Mart >> >> ------------------------------------------------------------------------- >> This SF.Net email is sponsored by the Moblin Your Move Developer's challenge >> Build the coolest Linux based applications with Moblin SDK & win great prizes >> Grand prize is a trip for two to an Open Source event anywhere in the world >> http://moblin-contest.org/redirect.php?banner_id=100&url=/ >> _______________________________________________ >> Astlinux-users mailing list >> Astlinux-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/astlinux-users >> >> Donations to support AstLinux are graciously accepted via PayPal to >> pay...@krisk.org. >> > > ------------------------------------------------------------------------- > This SF.Net email is sponsored by the Moblin Your Move Developer's challenge > Build the coolest Linux based applications with Moblin SDK & win great prizes > Grand prize is a trip for two to an Open Source event anywhere in the world > http://moblin-contest.org/redirect.php?banner_id=100&url=/ > _______________________________________________ > Astlinux-users mailing list > Astlinux-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/astlinux-users > > Donations to support AstLinux are graciously accepted via PayPal to > pay...@krisk.org. > ------------------------------------------------------------------------------ _______________________________________________ Astlinux-users mailing list Astlinux-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/astlinux-users Donations to support AstLinux are graciously accepted via PayPal to pay...@krisk.org.
