Thanks Michael. It does look that way.
Hmm thanks for pointing out the error.
I realise that I am now confused about sensors.conf for the Jetway NF9HG-2930 &
Qotom Q190G4N-S07 & Qotom Q530G6.
Is the file empty with just comments or does the # mean something?
# libsensors configuration file
# -----------------------------
# Qotom Q530G6
# coretemp CPU sensor
Regards
Michael Knill
On 17/8/19, 6:48 pm, "Michael Keuter" <li...@mksolutions.info> wrote:
> Am 17.08.2019 um 05:16 schrieb Michael Knill
<michael.kn...@ipcsolutions.com.au>:
>
> Hi Group
>
> I have an APU2 installed running version 1.3.6. Due to a UPS battery
change, they powered down the APU but had problems with the system on powerup.
> Symptoms were that you could not web or SSH into box. Attended site and
plugged in a serial cable and found that the flash could not be read or there
were errors (logs attached).
> I rebooted the box and it went into a Memory test for some reason which
was taking AGES to complete:
>
> Memtest86+ 5.01 coreboot 001| AMD GX-412TC SOC
> CLK: 998.2MHz (X64 Mode) | Pass 4% #
> L1 Cache: 32K 17824 MB/s | Test 42% ################
> L2 Cache: 2048K 5145 MB/s | Test #5 [Moving inversions, 8 bit pattern]
> L3 Cache: None | Testing: 1024K - 1920M 1919M of 1919M
> Memory : 1919M 1547 MB/s | Pattern: 20202020 | Time:
0:01:08
>
------------------------------------------------------------------------------
> Core#: 0 (SMP: Disabled) | CPU Temp | RAM: 666 MHz (DDR3-1333) - BCLK:
100
> State: - Running... | 59 C | Timings: CAS 9-9-10-24 @ 64-bit
Mode
> Cores: 1 Active / 1 Total (Run: All) | Pass: 0 Errors:
0
>
------------------------------------------------------------------------------
>
> I got sick of waiting so I rebooted again and it all came up fine.
> I have attached a file with all the logs from these steps.
>
> The reason I am concerned is that I had another one of my APU boxes
running 1.3.6 just lock up for some reason and was also fixed with a reboot. I
could not find any logs for that one and it may not be related.
> So my questions are:
> • Is this just an unlucky flash problem or could there be something
more sinister?
> • Why did it need to do a Memtest when it rebooted. Is this a BiOS
thing?
Hi Michael,
to me it looks as the mSATA had an issue. Maybe the APU couldn't boot from
the mSATA and ran into memtest (but that is speculation).
I would replace the mSATA.
BTW: Though unrelated, there was a error message regarding
"/etc/sensors3.conf".
Error: File /etc/sensors3.conf, line 5: Invalid keyword
Mine looks like this:
----
# libsensors configuration file
# -----------------------------
# PC Engines APU2
# k10temp CPU sensor
----
> Thanks all.
>
> Regards
> Michael Knill
> <Astlinux error log.txt>
Michael
http://www.mksolutions.info
_______________________________________________
Astlinux-users mailing list
Astlinux-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/astlinux-users
Donations to support AstLinux are graciously accepted via PayPal to
pay...@krisk.org.
_______________________________________________
Astlinux-users mailing list
Astlinux-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/astlinux-users
Donations to support AstLinux are graciously accepted via PayPal to
pay...@krisk.org.
